• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.11
• /
• pp.731-738
• /
• 2015

This study proposed the method of the multi-crack detection using the sensitivity coefficient matrix which is calculated from the change of eigenvalues and eigenvectors before and after the crack. Each crack is modeled by a rotational springs. The method is applied to the cantilever beam with miulti-crack. The eigenvalues and eigenvectors are determined for different crack locations and depths. The prediction of multi-crack detection are in good agreement with the results of structural reanalysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.887-887
• /
• 2004

The areal density of the hard disk drive(HDD) has been increased due to technological advances recently. To achieve the high areal density magnetic recording requires an extremely small gap between the air-bearing surface (ABS) and disk. At the same time, the slider mass and size should be reduced to minimize the physical contact under the operational and environmental conditions. Almost all of 2.5＂HDD companies will get ready for adoption of FEMTO slider and already utilized the small slider. FEMTO and small size slider will be mainstream in the 2.5" and other small form factor HDD in the near future. In this study, the flying characteristic of FEMTO slider was examined. Based on the simulation, FEMTO slider is very stable in flying dynamic under the disk modulation, however the flying height sensitivity of the manufacturing tolerances is much bigger than PICO slider. And the other characteristics like impulse response and load/unload dynamic were also examined in this study.tudy.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.888-893
• /
• 2004

This paper proposed a dual actuator using bimorph PZT for information storage device based on prove array NSOM(Near-field Scanning Optical Microscopy). The gap between the media and the optical head should be maintained within the optical tolerance. Therefore, a new actuator having high sensitivity is required. Bimorph PZT, which has fast access time and high sensitivity characteristic, is suitable for this precise actuating system. This paper is focused on derivation of mathematical model of dual bimorph PZT actuator and control algorithm. Hamilton's principle was used for mathematical model. The model is verified by FEA(Finite Element Analysis), and compared with experimental results. Different control algorithms were used f3r two bimorph PZT actuating same direction and opposite direction. The gap between recording media and optical head was controlled within 20nm in experiment.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.556-562
• /
• 2000

This paper presents new sensitivity analysis algorithm for the dynamic response of three dimensional rectilinear type structure. This method is derived from a combination of the transfer stiffness coefficient method(TSCM) and the Newmark method. We developed dynamic response analysis algorithm by TSCM. This method has more safe computational precision and time than transfer matrix method(TMM). We defined new design variable and object function, and computated simple three dimensional computation model by TSCM. The presented analysis algorithm was validated by results of changing design variable.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.472-478
• /
• 2000

The vibration of the hard disk drive (HDD) systems, which comprises flexible disks, flexible shafts, bearings, and base structures, are analyzed by a finite element method (FEM) to cope with complicated coupling effects between them. The natural frequencies and mode shapes of the uncoupled, axial and bending coupled vibrations are calculated. Modal testing of the HDD systems is performed to validate the finite element analysis (FEA) results. Good agreement was obtained between the computed and experimental results. Sizing design sensitivity analysis (DSA) of the system was performed with the thickness of base structure and bearing stiffness as design variables. The DSA results tell how can I increase or decrease eigenvalue of the system effectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1633-1640
• /
• 2000

The finite element analysis (FEA) is widely used in modem structural dynamics because the performance of structure can be predicted in early stage. However, due to the difficult in determination of various uncertain parameters, it is not be easy to obtain a reliable finite element model. To overcome these difficulties, updating program of FE model is developed by consisting of pretest, correlation and updating. In correlation, it calculates modal assurance criteria, cross orthogonality, mixed orthogonality and coordinate modal assurance criteria. For the model updating, the continuum sensitivity analysis and design optimization tool (DOT) are used. The SENSUP program is developed for model updating to obtain physical parameter sensitivity. The developed program is applied to practical examples such as the base plate of HDD, BLDC spindle motor, and upper housing of induction motor. And the sensor placement for the square plate is compared using several methods.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1675-1680
• /
• 2000

Recently the uncertainty has been made rapid progress in various fields of industry but the uncertainty measurement method of acoustical test (i.e. Insertion loss, Absorption ratio, Transmission loss etc,) hasn't been established. In this study, the uncertainty of measurement method for ducted silencers is carried out according to ISO 7235. The standard uncertainty factors are composed of sound pressure level, microphone sensitivity and pistonphone calibration in this measurement. Sound pressure level is type A evaluation of uncertainty, microphone sensitivity and pistonphone calibration are type B evaluation of uncertainty. The combined standard uncertainty is calculated by two type evaluation. The expanded uncertainty is expressed by the combined standard uncertainty multiply k value which is yield the effective degree of freedom.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.2
• /
• pp.106-111
• /
• 2011

In this paper, assumed mode method on Euler beam theory is employed and signal distortion is considered to obtain the performances of a MEMS accelerometer which are a sensitivity and measurable frequency range(MFR). Not only the sensitivities and MFR but also the variations of dynamic responses and natural frequencies of the MEMS accelerometer are investigated for several sets of beam properties such as length, width, thickness and Young's modulus. It is stated that the variations of beam properties significantly influence the performances of the MEMS accelerometer and the relationship between sensitivities and MFR is inversely proportional to each other.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.208-213
• /
• 2003

A note-book PC has become thinner in recent years. And optical disc drives are required to have high memory capacity. Therefore, the actuator of optical disc drives must be thinner and have disc tilt compensation function for high density memory. In this paper, the hybrid type actuator is investigated for 3-axis ultra-slim actuator. A 3-axis ultra-slim actuator is designed by using the modal analysis of the actuator and the electromagnetic analysis of magnetic circuit to achieve dynamic characteristics and magnetic flux density for high sensitivity, respectively. Also, magnetic force between tilt magnet and tilt yoke is investigated to find the influence on the DC sensitivity in the focus and track directions.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.226-233
• /
• 2003

There are many researches going on to develop the information storage devices using Blue-ray disc and DVD as a demand for high-density information storage devices is highly increasing. This high-density information storage device requires a short-wave laser and objective lens of high numerical aperture set in fer its operation. And, that brings out rapid decrease of tilt tolerance. Therefore, it is necessary that an actuator should control tilt motions to get a stable signal. In this paper, a new mathematical form of 3-D.O.F coupled model is formulated and magnetic circuit in constraints is most effectively designed with the use of the moving coil type actuator in higher sensitivity. Further, this paper presents a tilt coil whose rotational center point is put on that of the lens through the variation of tilt coil and proposes a 3-axis actuator with high sensitivity improved in its dynamic property through its structure analysis.