• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.4
• /
• pp.360-368
• /
• 1988

A 14 to 14.5 GHz low noise MIC amplifier is designed on the $Al_2$$O_3$ substrate. The amplifier which uses a GaAsMESFET developed at COMSAT Laboratories has been designed and optivized to have gain greater than 7dB and noise figure less than 2dB using Super-Compact program. Experimental results show that the gain of the amplifier is 7 to 7.7 dB, while noise figure is 3.8 to 4.3dB through the desired band.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.1
• /
• pp.41-48
• /
• 2002

This paper presents a 18-mW, 2.5-㎓ fractional-N frequency synthesizer with l-bit $4^{th}$-order interpolative delta-sigma ($\Delta{\;}$\sum$)modulator to suppress fractional spurious tones while reducing in-band phase noise. A fractional-N frequency synthesizer with a quadruple prescaler has been designed and implemented in a $0.5-\mu\textrm{m}$ 15-GHz $f_t$ BiCMOS. Synthesizing 2.1 GHzwith less than 200 Hz resolution, it exhibits an in-band phase noise of less than -85 dBc/Hz at 1 KHz offset frequency with a reference spur of -85 dBc and no fractional spurs. The synthesizer also shows phase noise of -139 dBc/Hz at an offset frequency of 1.2 MHz from a 2.1GHz center frequency.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.200-201
• /
• 2002

Recently, a countermeasure for the electromagnetic noise emission on RF integrated transmission line using the loss generation of ferromagnetic thin films is briefly suggested$\^$1,2/. Without the magnetic film, the noise harmonics of the signal pass through the transmission line with only a little attenuation. The ideal role of magnetic film is not to raise insertion losses in the pass-band and to give as large attenuation as possible to eliminate the noise harmonics at the stop-band, the frequency range higher than the meaningful signal as shown in Fig. 1. and Fig. 2. (omitted)

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.713-717
• /
• 2014

This paper presents a beamforming technique for locating impulsive sound source. The conventional frequency-domain beamformer is advantageous for localizing noise sources for a certain frequency band of concern, but the existence of many frequency components in the wide-band spectrum of impulsive noise makes the beamforming image less clear. In contrast to a frequency-domain beamformer, it has been reported that a time-domain beamformer can be better suited for transient signals. Although both frequency- and time-domain beamformers produce the same result for the beamforming power, which is defined as the RMS value of its output, we can use alternative directional estimators such as the peak value and crest factor to enhance the performance of a time-domain beamformer. In this study, the performance of three different directional estimators, the peak, crest factor and RMS output values, are investigated and compared with the incoherent interfering noise embedded in multiple microphone signals. The proposed formula is verified via experiments in an anechoic chamber using a uniformly spaced linear array. The results show that the peak estimation of beamformer output determines the location with better spatial resolution and a lower side lobe level than crest factor and RMS estimation in noise free condition, but it is possible to accurately estimate the direction of the impulsive sound source using crest factor estimation in noisy environment with stationary interfering noise.

• Journal of Advanced Navigation Technology
• /
• v.8 no.2
• /
• pp.176-183
• /
• 2004

In this paper, two-stage low noise amplifier(LNA) for S-band is designed and implemented using ATF54143 HEMT of HP CO. In order to get noise figure and input VSWR to be wanted, it is considered input VSWR and noise figure simultaneously in matching-circuit designing. The fabricated two-stage low noise amplifier has the gain of 27.8dB, input VSWR and output VSWR under 1.5.

• Korean Journal of Metals and Materials
• /
• v.49 no.4
• /
• pp.329-333
• /
• 2011

To develop wide-band noise absorbers with a special design for low-frequency performance, this study proposes a tin oxide (Sn-O) thin films as the noise absorbing materials in a microstrip line. Sn-O thin films were deposited on polyimide film substrates by reactive sputtering of the Sn target under flowing $O_{2}$ gas, exhibiting a wide variation of surface resistance (in the range of $10^{0}-10^{5}{\Omega}$) depending on the oxygen partial pressure during deposition. The microstrip line with characteristic impedance of $50\Omega$ was used for the measurement of noise absorption by the Sn-O films. The reflection parameter $(S_{11})$ increased with a decrease of surface resistance due to an impedance mismatch at the boundary between the film and the microstrip line. Meanwhile, the transmission parameter $(S_{21})$ diminished with a decrease of surface resistance resulting from an Ohmic loss of the Sn-O films. The maximum noise absorption predicted at an optimum surface resistance of the Sn-O films was about $150{\Omega}$. For this film, greater power absorption is predicted in the lower frequency region (about 70% at 1 GHz) than in conventional magnetic sheets of high magnetic loss, indicating that Ohmic loss is the predominant loss parameter for the conduction noise absorption in the low frequency band.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.5A
• /
• pp.484-491
• /
• 2004

C-band pumping effect appears in L-band EDFA because the absorption in C-band occurs dominant under the condition of such a low average population inversion. In this paper, we show how the C-band pumping effect depends on 980nm pump power, the C-band wavelength, and its input power. The C-band pumping is caused by absorbing C-band injection or backward spontaneous emission power through EDF. If the same small signal condition is given by a C-band pump, the C-band pump of a long wavelength is good for the saturation and noise characteristics of L-band signal. Finally, it is considered that in the aspect of saturation characteristics, C-band compensation is not so much efficient as L-band in Gain-Clamped L-band EDFA having a lossy resonator.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.330-331
• /
• 2009

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.534-537
• /
• 2011

This Paper present prediction Vehicle Interior Noise using ATF(Acoustic Transfer Function) and engine radiated sound power. This is useful tool to qualifying the effectiveness of Air-borne noise Path. Furthermore This method provide acoustic package performance of the vehicle and able to prepare frequency band to same segment or benchmarking vehicle.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.1157-1160
• /
• 2002

This paper describes an investigative study for Wind Noise of Passenger Cars. Using statistical method of analyzing jury preference data, we extract important sound quality metrics for subjective feeling and also md important frequency band. It will be helpful for development of wind Noise improvement.