• Journal of the Korean Society of Combustion
• /
• v.12 no.2
• /
• pp.26-33
• /
• 2007

To reveal the newly found liftoff height behavior of hydrogen jet, we have experimentally studied the stabilization mechanism of turbulent, lifted jet flames in a non-premixed condition. The objectives of the present research are to report the phenomenon of a liftoff height decreasing as increasing fuel velocity, to analyse the flame structure and behavior of the lifted jet, and to explain the mechanisms of flame stability in hydrogen turbulent non-premixed jet flames. The velocity of hydrogen was varied from 100 to 300m/s and a coaxial air velocity was fixed at 16m/s with a coflow air less than 0.1m/s. For the simultaneous measurement of velocity field and reaction zone, PIV and OH PLIF technique was used with two Nd:Yag lasers and CCD cameras. As results, it has been found that the stabilization of lifted hydrogen diffusion flames is related with a turbulent intensity, which means that combustion occurs at the point where the local flow velocity is balanced with the turbulent flame propagation velocity.

• Structural Engineering and Mechanics
• /
• v.62 no.6
• /
• pp.739-748
• /
• 2017

Notches such as slots are typical geometric features on mechanical components that promote fatigue crack initiation. Unlike for components with open hole type notches, there are no conventional treatments to enhance fatigue behavior of components with slots. In this work we evaluate the viability of applying laser shock peening (LSP) to extend the fatigue life of 6061-T6 aluminum components with slots. The feasibility of using LSP is evaluated not only on damage free notched specimens, but also on samples with previous fatigue damage. For the LSP treatment a convergent lens was used to deliver 0.85 J and 6 ns laser pulses 1.5 mm in diameter by a Q-switch Nd: YAG laser, operating at 10 Hz with 1064 nm of wavelength. Residual stress distribution was assessed by the hole drilling method. A fatigue analysis of the notched specimens was conducted using the commercial code FE-Safe and different multiaxial fatigue criteria to predict fatigue lives of samples with and without LSP. The residual stress field produced by the LSP process was estimated by a finite element simulation of the process. A good comparison of the predicted and experimental fatigue lives was observed. The beneficial effect of LSP in extending fatigue life of notched components with and without previous damage is demonstrated.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.112-114
• /
• 1999

Superconducting multiplexer consisting of hairpin type filters has been designed for the reduction of the physical size of the device. Pulsed laser deposition with a Nd:YAG laser has been used to grow high quality YBCO superconducting films on MgO substrates. Multiplexer has been designed to have the center frequencies at 13.6 CHz and 13.9 GHz on MgO substrate with the size of 20 ${\times}$ 20 ${\times}$ 0.5mm$^3$. It is possible to implement superconducting multiplexer having two passbands on the limited 20 ${\times}$ 20 ${\times}$ 0.5mm$^3$ MgO substrate by adopting hairpin type filters. This type of superconducting device will be useful for the integration of microwave subsystem.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.253-255
• /
• 2006

Grey relational analysis has been carried out to develop a new approach for optimization of Nd:YAG laser and MIG hybrid welding parameters. The quality of welded material depends on welding parameters. The parameters chosen for current study include wire type, shielding gas, laser energy, laser focus, traveling speed, and wire feed rate. The welding experiments were performed on 6K21-T4 aluminum alloy sheet. Functional demands on products may vary widely depending on their use. The ultimate tensile stress, width, and penetration were chosen as the optimization criterion. Practice based on an orthogonal array which is following Taguchi's method has been progressed. Base on the results of grey relational analysis, the optimal process parameters were obtained. This integrated work was judged and it is observed that the results obtained by using the optimal parameters are much improved compared to those obtained through initial setting.

• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.285-290
• /
• 1995

High quality $Y_{1}$Ba$_{2}$Cu$_{3}$$O_{7-x}$ thin films have been fabricated by pulsed Nd:YAG laser deposition using an unusual 'off-axis' target-substrate geometry. Various properties of superconducting $Y_{1}$Ba$_{2}$Cu$_{3}$$O_{7-x}$ thin films have been studied systematically as a function of oxygen pressure during the deposition, in both 'on-axis' and the unusual 'off-axis' target substrate geometries. In the 'off-axis' geometry, one can completely eliminate the so-called 'laser droplets' from the film surface and thus obtain smooth high quality films. It is found that films with optimum structural and electrical properties are obtained at a lower oxygen pressure range during the 'off-axis' deposition when compared with that required in the 'on-axis' deposition geometry.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.598-602
• /
• 2004

Organic light entitling diode panel was fabricated using pulsed laser deposition (PLD) method Nd-YAG laser with Q-Switched and 355 nm pulse was used for the PLD. While TPD(N,N'-Di-[naphthaleny]-N, N'-diphenyl-benzidine) was used as a HTL(Hole transport layer), $Alq_3$(8-Hydroxyquinoline, Aluminum Salt) was used as EML/ETL(Emitting Layer/Electron Transport Layer) Organic pellet was fabricated and employed for the PLD method. The absorbances of the organic films were investigated and the measured absorbance values of TPD and $Alq_3$ films was 362 nm and 399 nm, respectively. The turn-on voltage of the OLED panel was 7.5 V and its luminance was $90\;cd/m^2$

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1033-1036
• /
• 2004

Si nanocrystallites thin films on p-type (100) Si substrate have been fabricated by pulsed laser deposition using a Nd:YAG laser. After deposition, samples were annealed at the temperatures of 400 to $800^{\circ}C$. Hydrogen passivation was then performed in the forming gas (95% $N_2$ + 5% $H_2$) for 1 hr. Strong violet-indigo photoluminescence has been observed at room temperature from nitrogen ambient-annealed Si nanocrystallites. The variation of photoluminescence (PL) Properties of Si nanocrystallites thin films has been investigated depending on annealing temperatures with hydrogen passivation. From the results of PL, Fourier transform infrared (FTIR), and high-resolution transmission electron microscopy (HRTEM) measurements, it is observed that the origin of violet-indigo PL from the nanocrystalline silicon in the silicon oxide film is related to the quantum size effect of Si nanocrystallites and oxygen vacancies in the SiOx(x : 1.6-1.8) matrix affects the emission intensity.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1549-1551
• /
• 1998

We have designed and developed narrow bandpass multipole filters for satellite communication using $YBa_2Cu_3O_{7-x}$(YBCO) thin films on MgO substrates. The superconducting film used in this study was prepared by laser ablation on one side polished MgO (100) substrates. A Nd:YAG laser was used to fabricate YBCO thin films. The wave length of the laser was 355 nm. The laser beam was focused onto a YBCO target rotating linearly to avoid deep craters that may eject macroscopic YBCO particles. The YBCO films were grown at $750^{\circ}C$ in the oxygen partial pressure of 200 mTorr. The deposited YBCO thin films were patterned by conventional wet-etching method. The transition temperatures of YBCO thin films were 85 - 88 K and the film thicknesses were about 5,000 $\AA$. By comparing the performances of normal-metal filters and YBCO filters, we observed that superconducting YBCO multipole filters have been showed superior performances at 77 K.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.200-200
• /
• 2008

This paper reports on electrical characterization by IDC pattern using BST$(Ba_{0.5}Sr_{0.5}TiO_3)$ thin film. BST thin films have been deposited on $Al_2O_3$ Substrates by Nd-YAG pulsed laser deposition with a 355nm wavelength at $700^{\circ}C$. The post deposition annealing at $750^{\circ}C$ in flowing $O_2$ atmosphere for I hours. The capacitance of IDC patterns have been measured from 1 to 10 GHz as a function fo electric field (${\pm}40$ KV/cm) at room temperature using interdiigitated Au electrodes deposited on top of BST. The IDC patterns have three type of fingers number. For the finger paris was increased onto $Al_2O_3$, the capacitance increased. The capacitance of 5 pairs finger was 0.3pF and 10 pairs finger was 0.9pF.

• Journal of computational fluids engineering
• /
• v.15 no.3
• /
• pp.39-45
• /
• 2010

The turbulent flows in a tunnel mock-up($10L{\times}0.5W{\times}0.25H$ m3 : scale reduction 1/20) with rectangular cross section were investigated. The instantaneous velocity fields of Re = 49,029, 89,571 were measured by the 2-D PIV system which is consisted of double pulsed Nd:Yag laser and the tracer particles in the straight-duct mock-up where the flows were fully developed. The mean velocity profiles were taken from the ensemble averages of 1,000 instantaneous velocity fields. Simultaneously, numerical simulations(RANS) were performed to compare with experimental data using STREAM code. Non-linear eddy viscosity model (NLEVM : Abe-Jang-Leschziner Eddy Viscosity Model) was employed to resolve the turbulent flows in the duct. The calculated mean velocity profiles were well compared with PIV results. In the log-law profiles, the experimental data were in good agreement with numerical simulations all the way to the wake region except the viscous sub-layer (near wall region).