• 한국결정성장학회지
• /
• 제10권3호
• /
• pp.233-238
• /
• 2000

생체적합성과 상 안정성이 우수한 t-$ZrO_2/Al_2O_3$복합체에 $Eu_2O_3$을 0~4 mol%첨가한 복합체를 $1600^{\circ}C$ 온도에서 1 시간 소결하여 상 안정성, 색상변화, 기계적 특성을 조사하였다. $180^{\circ}C$, 3.5MPa의 수증기 압력 하에서 20시간 열처리 후 X-선 회절법으로 관찰한 결과 $Eu_2O_3$가 첨가된 (Y,Nb,Eu)-TZP/$Al_2O_3$복합체는 우수한 상 안정성이 유지되었다. $Eu_2O_3$의 양이 증가함에 따라 백색계통의 상아색에서 미색의 핑크색으로 서서히 변화하였다 $Eu_2O_3$가 3 mol%까지 첨가된 복합체의 경우 620MPa, 7.6MPa.$m^{1/2}$ 이상의 강도와 인성값이 관찰되었다.

• 대한금속재료학회지
• /
• 제48권8호
• /
• pp.741-748
• /
• 2010

We studied the corrosion and oxidation properties of Fe-18Cr-0.4Nb-(0.1~0.6)Ti-(1~3)Si-(0.5~2)Mo stainless steel. The resistance to general and pitting corrosion was evaluated and the results were analyzed by Response Surface Methodology (RSM) as a function of alloy composition. The effects of alloy composition and heat treatment on the oxidation resistance were also examined. Mo increased both general corrosion resistance and pitting corrosion resistance. Si improved the resistance of the alloys to pitting corrosion. Si was also beneficial for general corrosion resistance of the alloys containing Mo at more than 1 wt.%. However, Mo was detrimental when its content was lower. Effects of Ti on general corrosion properties appeared to be weak and a high concentration of Ti appeared to deteriorate pitting resistance. The thickness of the oxidation scale increased and adhesion of the scale worsened as the temperature increased from $800^{\circ}C$ to $900^{\circ}C$. Weight gain of the alloys due to oxidation at $900^{\circ}C$ clearly showed that the resistance to oxidation is improved by annealing at $860^{\circ}C$ and an increase of Si content.

• 대한금속재료학회지
• /
• 제48권1호
• /
• pp.39-48
• /
• 2010

In order to investigate the effects of tempering temperature and heat-treatment path on the microstructural and mechanical properties of ASTM Gr.92 steels, four samples with different tempering temperatures and heat-treatment paths wer prepared. THeree experimental steels showed tempered martensitic microstructures, but the sample tempered at $810^{\circ}C$ was presumed to retain partially untempered martensitic microstructures due to a lower ${\alpha}$+${\gamma}$ phase regime. $M_{23}C_6$, V(C,N), and Nb(C,N) precipitates were observed in all samples. In addition $Cr_2N$ was observed to be precipitated finely and uniformly by isothermal heat-treatment. The lath width and precipitate size in the isothermal heat-treated samples were much smaller than those of the tempered-only specimens. Because of a fine and uniform precipitate, a reduction of lath width would enhance precipitation hardeing, and it was shown that mechanical propertiesincluding the hardness and tensile properties of the steels were improved by isothermal heat-treatment.

• 자원환경지질
• /
• 제42권3호
• /
• pp.177-193
• /
• 2009

삼광광상은 선캠브리아기 경기육괴의 화강편마암내에 발달된 단열대(NE, NW)를 따라 충진한 8개의 괴상맥으로 구성된 중열수 석영맥광상이다. 이 광상의 광화작용은 여러번의 단열작용에 의해 형성된 두시기의 석영+방해석시기(광화I시기)와 방해석시기(광화II시기)로 구성된다. 광화I시기의 열수작용에 의한 변질작용은 견운모화, 녹니석화, 탄산염화, 황철석화, 규화, 및 점토화작용등이 관찰되며 견운모대는 석영맥과 접촉한 부분에서 녹니석대는 석영맥으로부터 멀어짐에 따라 관찰된다. 견운모대의 모암변질광물은 대부분이 견운모 및 석영이며 일부 일라이트, 탄산염광물, 녹니석으로 구성된다. 녹니석대의 모암변질광물은 주로 녹니석, 석영과 소량 견운모, 탄산염광물 및 녹염석으로 구성된다. 견운모의 Fe/(Fe+Mg) 값은 0.45${\sim}$0.50(0.48$\pm$0.02)이며 백운모-펜자이트족에 해당되고 녹니석의 Fe/(Fe+Mg) 값은 0.74${\sim}$0.81(0.77$\pm$0.03)이고 대부분 브런스비자이트에 해당된다. 견운모와 녹니석에 대한 $Al_{IV}$-FE/(FE+Mg)의 다이어그램은 변질시 같은 광종의 견운모와 녹니석의 형성온도를 나타내는 지시자로써 유용하다. 이것은 계산된 녹니석 단종의 활동도가 $a3(Fe_5Al_2Si_3O_{10}(OH)_6$=0.0275${\sim}$0.0413, $a2(Mg_5Al_2Si_3O_{10}(OH)_6$=1.18E-10${\sim}$7.79E-7, $a1(Mg_6Si_4O_{10}(OH)_6$=4.92E-10${\sim}$9.29E-7로서 삼광광상의 녹니석은 iron-rich 녹니석으로 비교적 고온 (T>450$^{\circ}C$에서 모암과 평형상태에서 온도가 감소함에 따라 형성되었음을 알 수 있다. 모암변질시 ${\alpha}Na^+$, ${\alpha}K^+$, ${\alpha}Ca^{2+}$ 및 ${\alpha}Mg^{2+}$는 각각 ${\alpha}Na^+$=0.0476($400^{\circ}C$), 0.0863($350^{\circ}C$), ${\alpha}K^+$=0.0154($400^{\circ}C$), 0.0231($350^{\circ}C$), ${\alpha}Ca^{2+}$=2.42E-11($400^{\circ}C$), 7.07E-10($350^{\circ}C$), ${\alpha}Mg^{2+}$=1.59E-12($400^{\circ}C$), 1.77E-11($350^{\circ}C$)이며 열수용액의 pH는 5.4${\sim}$6.4($400^{\circ}C$), 5.3${\sim}$5.7($350^{\circ}C$)로서 모암변질시 열수용액는 약산성이었음을 알 수 있다. 모암변질시 이득원소(부화원소)는 $TiO_2$, $Fe_2O_3(T)$,CaO, MnO, MgO, As, Ag, Cu, Zn, Ni, Co, W, V, Br, Cs, Rb, Sc, Bi, Nb, Sb, Se, Sn 및 Lu 등이며 특히 대부분의 광상에서 Ag, As, Zn, Sc, Sb, S,$CO_2$ 등의 원소가 현저하게 증가하므로 중열수 및 천열수 금-은광상의 탐사에 지시원소로서 활용될 수 있을 것이다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.184-184
• /
• 2009

Lead-free Piezoelectric $[Li_{0.04}(Na_{0.44}K_{0.56})](Nb_{0.88}Ta_{0.1}Sb_{0.02})$ (abbreviated as NKNLTS) has been synthsized by conventional mixed oxide method traditional ceramics process without cold-isostatic pressing. Effect of $Bi_2O_3$ addition on NKNLTS ceramics was investigated. Piezoelectric properties of the ceramic were varied with the amount of $Bi_2O_3$ addition and showed the maximum Kp value at 0.4wt% $Bi_2O_3$ addition. The results show that the optimum poling condition for NKNLTS ceramics of 3.5kV/mm, poling temperature of $120^{\circ}C$ and poling time of 30min. At the sintering temperature of $1100^{\circ}C$ and the calcination temperature $800^{\circ}C$, the optimal values of density=$4.7g/cm^2$, Kp=0.44, $\varepsilon_r$=1309 were obtained. Consequently, lead free piezoelectric ceramics with the excellent piezoelectric could be fabricated using a conventional mixed oxide process and the optimal manuacturing condition of those was obtained.

• 열처리공학회지
• /
• 제22권5호
• /
• pp.290-297
• /
• 2009

In case of using Asymmetric Bipolar Pulsed DC (ABPD) power generator, thin film is efficiently deposited as ions are getting higher energy by suppressing target poisoning and electric arc. In this article, the mechanical properties of CNx thin films deposited on the STS 316L were compared with DC and ABPD power generators. The CNx thin films deposited with ABPD clearly improved wear resistance by higher ratio of sp3CN as compared with DC. Nb interlayer affected to increase the value of 10N of adhesion between CNx thin films and substrate. But, CNx thin films deposited with ABPD couldn't endure to wear load and decreased wear resistance as the films were too thinner than substrate. Nevertheless the higher substrate bias energy applied to perform the dense films, it wasn't shown benefits about the wear properties from DC sputtering. But, in case of using ABPD sputtering, the wear resistance was largely improved without changing morphology despite of thin films.

• 한국분말재료학회지
• /
• 제13권4호
• /
• pp.256-262
• /
• 2006

The amorphous $Fe_{73}Si_{16}B_7Nb_3Cu_1$ alloy strip was pulverized to get a flake-shaped powder after annealing at $425^{\circ}C$ for 90 min and subsequently ground to obtain finer flake-shaped powder by using a ball mill. The powder was mixed with polyimide-based binder of $0.5{\sim}3wt%$, and then the mixture was cold compacted to make a toroidal powder core. After crystallization treatment for 1 hour at $380{\sim}600^{\circ}C$, the powder was transformed from amorphous to nanocrystalline with the grain size of $10{\sim}15nm$. Soft magnetic characteristics of the powder core was optimized at $550{\sim}600^{\circ}C$ with the insulating binder of 3wt%. As a result, the powder core showed the outstanding magnetic properties in terms of core loss and permeability, which were originated from the optimization of the grain size and distribution of the insulating binder.

• Journal of Welding and Joining
• /
• 제33권6호
• /
• pp.6-12
• /
• 2015

Thermal fatigue life of the automobile exhaust manifold is directly affected by the restraint force according to the structure of exhaust system and bead shape of the welded joints. In the present study, the microstructural changes and precipitation behavior during thermal fatigue cycle of the 18wt% Cr ferritic stainless steel weld heat affected zone (HAZ) considering restraint stress were investigated. The simulation of weld HAZ and thermal fatigue test were carried out using a metal thermal cycle simulator under complete constraint force in the static jig. The change of the restraint stress on the weld HAZ was simulated by changing the shape of notch in the specimen considering the stress concentration factor. Thermal fatigue properties of the weld HAZ were deteriorated during cyclic heating and cooling in the temperature range of $200^{\circ}C$ to $900^{\circ}C$ due to the decrease of Nb content in solid solution and coarsening of MX type precipitates, laves phase, $M_6C$ with coarsening of grain and softening of the matrix. As the restraint stress on the specimen increased, the thermal fatigue life was decreased by dynamic precipitation and rapid coarsening of the precipitates.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.723-727
• /
• 2003

[ $Sr_xBa_{1-x}Nb_2O_6$ ] (SBN, $0.25{\leq}x{\leq}0.75$) ceramic is a ferroelectric material with tetragonal tungsten bronze (TTB) type structure, which has a high pyroelectric coefficient and a nonlinear electro-optic coefficient value. In spite of its advantages, SBN has not been investigated well compared to other ferroelectric materials with perovskite structure. In this study, SBN thin film was manufactured by ion beam sputtering technique using the prepared SBN target in $Ar/O_2$ atmosphere. SBN30 thin film of $1000{\AA}$ was pre-deposited as a seed layer on $Pt(100)/TiO_2/SiO_2/Si$ substrate followed by SBN60 deposition up to $3000{\AA}$ in thickness. As-deposited SBN60/SBN30 layer was heat-treated at different temperatures of 650, 700, 750, and $800^{\circ}C$ in air, respectively The crystallinity and orientation behavior as well as electric properties of SBN60/SBN30 multi-layer were examined. The deposited layer was uniform and the orientation was shown primarily along (001) plane from XRD pattern. There was no difference in the crystal structure with heat-treatment temperature, but the electric properties depended on the heating temperature and was the best at $750^{\circ}C$. In electric properties of Pt/SBN60/SBN30/Pt thin film capacitor prepared, the remnant polarization (2Pr) value was $15{\mu}C/cm^2$, the coercive field (Ec) 75 kV/cm, and the dielectric constant 1075, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.869-873
• /
• 2004

[ $Sr_xBa_{1-x}Nb_2O_6$ ] (SBN, $0.25{\leq}x{\leq}0.75$) ceramic is a ferroelectric material with tetragonal tungsten bronze (TTB) type structure, which has a high pyroelectric coefficient, piezoelectric, and a photo refractive properties. In this study, SBN60(x=0.6) thin film was manufactured by ion beam sputtering technique. Using the prepared SBN60 target in $Ar/O_2$ atmosphere as-deposited SBN60 thin film on Pt(100)/$TiO_2/SiO_2/Si$ substrate crystallization and orientation behavior as well as electric properties of SBN60 thin film were examined. SBN60 deposition up to $3000{\AA}$ in thickness, SBN60 thin film was heat-treated at $650^{\circ}C{\sim}800^{\circ}C$. The orientation was shown primarily along (001) plane from XRD pattern where working pressure was $4.3{\times}10^{-4}$ torr. The deposited layer was uniform, preferred orientatin and crystallization behavior resulted in the change of $O_2$ ratio was observed. In electric propertie of Pt/SBN60/Pt thin film capacitor remnant polarization (2Pr) value was $10{\mu}C/cm^2$, the coercive filed (Ec) 50 kV/cm, and the dielectric constant 615, respectively.