• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.5
• /
• pp.655-662
• /
• 2004

An adsorption process to recover the pure $CH_4\;and\;CO_2$ from its mixture was examined. In this study, activated carbon fibers were used as a selective adsorbent. The activated carbon fibers has 78~94% micropore volume and 10.5~20.3${\AA}$ narrow pore size, and showed high adsorption rate and the good selectivity for $CO_2$ under the ambient pressure. The ACF with high surface area showed short mass transfer zone and long breakthrough time and, its adsorption capacity depended on the microporosity. Compared with single component adsorption, the amount adsorbed $CO_2$ on ACF increased by the roll-up of $CH_4$ in mixed gases. The adsorption selectivity increased as now rate and $CO_2$ concentration of mixed gases increased, showing 5.2 selectivity for 75% $CO_2$ concentration.

• Bulletin of the Korean Chemical Society
• /
• v.20 no.1
• /
• pp.69-75
• /
• 1999

The silica-pillared H-kenyaites were prepared by interlarmellar base-catalyzed reaction of tetraethylorthosilicate [TEOS, Si(OC2H5)4] intercalated into the interlayer of H-kenyaite. The intercalation of TEOS was conducted by the octylamine preswelling process, resulting in a dramatic increase in gallery height to 24.7 Å. The interlamellar hydrolysis of octylamine-TEOS/H-kenyaite paste were conducted between 10 min and 40 min in 0.00%, 0.05% and 0.10% NH3-water solution respectively, and resulting in siloxane-pillared H-kenyajte with gallery height of 28.2-31.8 Å. The calcination of samples at 538 ℃ resulted in silica-pillared H-kenyaites with a large surface areas between 411 m2/g and 885 m2/g, depending on the aging time and NH3 concentration. Samples with optimum specific surface areas and well ordered-basal spacing were obtained by reaction between 10 min and 40 min in pure water and 0.05% NH3-water solution. Mesoporous samples with narrow pore size distribution were also prepared by reaction for 10-40 min in 0.05% NH3 solution. Rapid interlamellar reaction of TEOS in pure water showed that intercalated octylamine itself could act as a base catalyst during interlamellar polycondensation of TEOS.

• Membrane Journal
• /
• v.27 no.2
• /
• pp.167-181
• /
• 2017

Graphene-based materials have been considered as a promising membrane material, due to its easy processability and atomic thickness. In this study, we studied on gas permeation behavior in few-layered GO membranes prepared by spin-coating method. The GO membrane structures were varied by using different GO flake sizes and GO solutions at various pH levels. The GO membranes prepared small flake size show more permeable and selective gas separation properties than large one due to shortening tortuosity. Also gas transport behaviors of the GO membranes are sensitive to slit width for gas diffusion because the pore size of GO membranes ranged from molecular sieving to Knudsen diffusion area. In particular, due to the narrow pore size of GO membranes and highly $CO_2$-philic properties of GO nanosheets, few-layered GO membranes exhibit ultrafast and $CO_2$ selective character in comparison with other gas molecules, which lead to outstanding $CO_2$ capture properties such as $CO_2/H_2$, $CO_2/CH_4$, and $CO_2/N_2$. This unusual gas transport through multi-layered GO nanosheets can explain a unique transport mechanism followed by an adsorption-facilitated diffusion behavior (i.e., surface diffusion mechanism). These findings provide the great insights for designing $CO_2$-selective membrane materials and the practical guidelines for gas transports through slit-like pores and lamellar structures.

• Applied Chemistry for Engineering
• /
• v.29 no.6
• /
• pp.759-764
• /
• 2018

3D porous carbon electrodes (cNPIM), prepared by solution casting of a polymer of intrinsic microporosity (PIM-1) followed by nonsolvent-induced phase separation (NIPS) and carbonization are presented. In order to effectively control the pore size of 3D porous carbon structures, cNPIM was prepared by varying the THF ratio of mixed solvents. The SEM analysis revealed that cNPIMs have a unique 3D macroporous structure having a gradient pore structure, which is expected to grant a smooth and easy ion transfer capability as an electrode material. In addition, the cNPIMs presented a very large specific surface area ($2,101.1m^2/g$) with a narrow micropore size distribution (0.75 nm). Consequently, the cNPIM exhibits a high specific capacitance (304.8 F/g) and superior rate capability of 77% in an aqueous electrolyte. We believe that our approach can provide a variety of new 3D porous carbon materials for the application to an electrochemical energy storage.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.2
• /
• pp.33-42
• /
• 2012

The purpose of this study is to determine the effect of soil grain size and its distribution on soil-water characteristic. To do this, soil-water characteristic tests were conducted on Saemangeum silt using the axis translation technique. For comparison, the test was also conducted on Jumunjin sand. Using the test results, the soil-water characteristic curves (SWCCs) of Saemangeum silt and Jumunjin sand were predicted by Van Genuchten model. By comparison and analysis between two SWCCs, the silt shows higher values of matric suction, water content, and air entry value than the sand. On the other hand, the sand has higher values of Van Genuchten model parameters of ${\alpha}$, $n$, $m$ than the silt. It indicates that the SWCC is significantly dependent on the structure of soils. In other words, if a soil has relatively high grain size and poor grain size distribution curve, the values of saturated volumetric water content, residual volumetric water content, and air entry value are small, and the variation of volumetric water content is high in accordance with the matric suction variation, and consequently it shows a narrow range of funicular region.

• Current Photovoltaic Research
• /
• v.8 no.1
• /
• pp.27-32
• /
• 2020

CuS thin films were deposited on glass substrates at room temperature by RF magnetron sputtering. The structural and optical properties of CuS thin films grown by varying RF-power from 40 W to 100 W were studied. From the XRD analysis, we confirmed hexagonal crystal structures grown in the preferred orientation of the (110) plane in all CuS thin films, and the intensity of the main diffraction peak increased in proportion to the increase of RF-power. In the case of CuS thin film deposited at 40W, small-sized particles formed a thin and dense surface morphology with narrow pore spacing, relatively. As the power increased, the grain size and grain boundary spacing increased sequentially. The peaks for the binding energy of Cu 2p_3/2 and Cu 2p_1/2 were determined at 932.1 eV and 952.0 eV, respectively. The difference in binding energy for the Cu²⁺ states was the same at 19.9 eV regardless of process parameters. The transmittance and band gap energy in the visible region tended to decrease with increasing sputtering powers.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.167-169
• /
• 2009

We have carried out quantitative structure and property analysis of the nanoporous structures of low dielectric constant (low-k) carbon-doped silicon oxide (SiCOH) films, which were deposited with plasma enhanced chemical vapor deposition (PECVD) using vinyltrimethylsilane (VTMS), divinyldimethylsilane (DVDMS), and tetravinylsilane (TVS) as precursor and oxygen as an oxidant gas. We found that the SiCOH film using VTMS only showed well defined spherical nanopores within the film after thermal annealing at $450^{\circ}C$ for 4 h. The average pore radius of the generated nanopores within VTMS SiCOH film was 1.21 nm with narrow size distribution of 0.2. It was noted that thermally labile $C_{x}H_{y}$ phase and Si-$CH_3$ was removed to make nanopore within the film by thermal annealing. Consequently, this induced that decrease of average electron density from 387 to $321\;nm^{-3}$ with increasing annealing temperature up to $450^{\circ}C$ and taking a longer annealing time up to 4 h. However, the other SiCOH films showed featureless scattering profiles irrespective of annealing conditions and the decreases of electron density were smaller than VTMS SiCOH film. Because, with more vinyl groups are introduced in original precursor molecule, films contain more organic phase with less volatile characteristic due to the crosslinking of vinyl groups. Collectively, the presenting findings show that the organosilane containing vinyl group was quite effective to deposit SiCOH/$C_{x}H_{y}$ dual phase films, and post annealing has an important role on generation of pores with the SiCOH film.

• Journal of Powder Materials
• /
• v.8 no.3
• /
• pp.163-167
• /
• 2001

A bulk porous $CaZrO_3/MgO$ composite with plantinum nano-dispersion was synthesized in air atmosphere through the combination of several in situ reactions, including the pyrolysis of $PtO_2$. A mixture of $CaMg(CO_3)_2$(dolomite), $ZrO_2$, $PtO_2$ and LiF (0.5 wt%, as an additive) was cold isostatically pressed at 200 MPa and sintered at $1100^{\circ}C$ for 2 h. The porous $CaZrO_3/MgO/Pt$ composite ($CaZrO_3/MgO$ : Pt=99 : 1 in volume) had a uniformly open-porous structure (porosity: 56%) with three-dimensional (3-D) network and a narrow pore-size distribution, similarly to the porous $CaZrO_3/MgO$ composites reported before. Catalytic Properties (viz., NO direct decomposition and NO reduction by $C_2H_4$) of the $CaZrO_3/MgO/Pt$ composite were investigated up to $900^{\circ}C$. In the absence of oxygen, the NO conversion rate reached ~52% for the direct decomposition and ~100% for the reduction by $C_2H_4$, respectively. The results suggest the possibility of the porous composite as a multifunctional filter, i.e., simultaneous hot gas-filtering and $de-NO_x$ in one component.

• Korean Journal of Materials Research
• /
• v.10 no.12
• /
• pp.845-852
• /
• 2000

Mesoporous ${\gamma}-Al_2O_3$ has been prepared by selective leaching of silica from calcined domestic kaolinite. From XRD and TG-DTA data, it was found that the microstructure of a spinel phase, consisting of ${\gamma}-Al_2O_3$ containing a small mount of amorphous silica, was obtained by calcining kaolinite samples at around $1000^{\circ}C$ for 24h. Porous ${\gamma}-Al_2O_3$ was prepared by selectively dissolving the amorphous silica in KOH solutions of 1~4M at temperatures of $25~90^{\circ}C$ for leaching time of 0.5~4h. In the case of the ${\gamma}-Al_2O_3$ obtained upon KOH treatment of 4M at $90^{\circ}C$ for 1h, it showed a very narrow unimodal pore size distribution, and also formed much mesopore at a diameter of around $40~80{\AA}$. The specific surface area was $250\textrm{m}^2/g$ and the total pore volume was $0.654\textrm{cm}^3/g$.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.3
• /
• pp.131-137
• /
• 2004

Sol-gel method which provides better electrochemical and physiochemical properties compared to the solid-state method was used to synthesize the material of $LiFe_yMn_{2-y}O_4$. Fe was substituted to increase the structural stability so that the effects of the substitution amount and sintering temperature were analyzed. XRD was used for the structural analysis of produced material, which in turn, showed the same cubic spinel structure as $LiMn_2O_4$ despite the substitution of $Fe^{3+}$. During the synthesis of $LiFe_yMn_{2-y}O_4$, as the sintering temperature and the doping amount of Fe(y=0.05, 0.1, 0.2)were increased, grain growth proceeded which in turn, showed a high crystalline and a large grain size, certain morphology with narrow specific surface area and large pore volume distribution was observed. In order to examine the ability for the practical use of the battery, charge-discharge tests were undertaken. When the substitution amount of $Fe^{3+}\;into\;LiMn_2O_4$ increased, the initial discharge capacity showed a tendency to decrease within the region of $3.0\~4.2V$ but when charge-discharge processes were repeated, other capacity maintenance properties turned out to be outstanding. In addition, when the sintering temperature was $800\~850^{\circ}C$, the initial capacity was small but showed very stable cycle performance. According to EVS(electrochemical voltage spectroscopy) test, $LiFe_yMn_{2-y}O_4(y=0,\;0.05,\;0.1,\;0.2)$ showed two plateau region and the typical peaks of manganese spinel structure when the substitution amount of $Fe^{3+}$ increased, the peak value at about 4.15V during the charge-discharge process showed a tendency to decrease. From the previous results, the local distortion due to the biphase within the region near 4.15V during the lithium extraction gave a phase transition to a more suitable single phase. When the transition was derived, the discharge capacity decreased. However the cycle performance showed an outstanding result.