• Korean Journal of Materials Research
• /
• v.22 no.5
• /
• pp.237-242
• /
• 2012

We report on the NO gas sensing properties of Al-doped zinc oxide-carbon nanotube (ZnO-CNT) wire-like layered composites fabricated by coaxially coating Al-doped ZnO thin films on randomly oriented single-walled carbon nanotubes. We were able to wrap thin ZnO layers around the CNTs using the pulsed laser deposition method, forming wire-like nanostructures of ZnO-CNT. Microstructural observations revealed an ultrathin wire-like structure with a diameter of several tens of nm. Gas sensors based on ZnO-CNT wire-like layered composites were found to exhibit a novel sensing capability that originated from the genuine characteristics of the composites. Specifically, it was observed by measured gas sensing characteristics that the gas sensors based on ZnO-CNT layered composites showed a very high sensitivity of above 1,500% for NO gas in dry air at an optimal operating temperature of $200^{\circ}C$; the sensors also showed a low NO gas detection limit at a sub-ppm level in dry air. The enhanced gas sensing properties of the ZnO-CNT wire-like layered composites are ascribed to a catalytic effect of Al elements on the surface reaction and an increase in the effective surface reaction area of the active ZnO layer due to the coating of CNT templates with a higher surface-to-volume ratio structure. These results suggest that ZnO-CNT composites made of ultrathin Al-doped ZnO layers uniformly coated around carbon nanotubes can be promising materials for use in practical high-performance NO gas sensors.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.3
• /
• pp.112-121
• /
• 2019

In this study, silicon / carbon nanotube / carbon composite particles with high capacity were fabricated by using micro-sized silicon particles and carbon nanotubes as an anode material for lithium ion batteries. The silicon / carbon nanotube / carbon composite particles were prepared by spray drying method to prepare spherical composite particles. The composite particles have the network structure of the carbon nanotubes around the silicon particles, in which the silicon particles and the carbon nanotubes are bonded by amorphous carbon. It appears that the volume expansion of silicon is effectively buffered and the electrical contact is maintained in the network structure of the composite particles during charge-discharge cycles.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.3
• /
• pp.339-344
• /
• 2008

Titanium dioxide nanotubes were fabricated by self-organized electrochemical potentiostatic anodization of titanium thin film with an electrolyte solution of sodium sulfate 1M and sodium flouride 0.5wt% aqueous solution at 20$^{\circ}C$ for 20min. Field Emmision Scanning Electron Microscopy(FE-SEM) and X-ray Diffractometer(XRD) were used to evaluate the micromorphology and crystalline structure of the titanium dioxide nanotube thin film. Titanium dioxide nanotube were fabricated with diameters approx. 100nm and tube length from appox. 1 $\mu$m. Titanium dioxide films formed through anodization and annealing process at 450$^{\circ}C$ contained a phase of anatase. Also, this study was performed to evaluate the application of titanium dioxide thin film for treating humic acid dissolved in water. The reaction tended to follow the Langmuir-Hinshelwood kinetics with zero order. Comparative experiments with thin film and anatase powder showed the same zero order kinetics when 0.3g of powder had been used.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.74-74
• /
• 2018

Ti-6Al-4V alloys have been widely used as orthopedic materials because of their excellent corrosion resistance and mechanical properties. However, it does not bind directly to the bone, so it requires a surface modification. This problem can be solved by nanotube and micropore formation. Plasma electrolytic oxidation (PEO) treatment for micropore, which combines high-voltage spark and electrochemical oxidation, is a new way of forming a ceramic coating on light metals such as titanium and its alloys. This method has excellent reproducibility and can easily control the shape and size of the Ti alloy. In this study, formation of bioactive surface by PEO-treatment after $2^{nd}$ ATO technique of Ti-6Al-4V alloy was invesgated by various instrument. Nanotube oxide surface structure was formed on the surface by anodic oxidation treatment in 0.8 wt.% NaF and 1M $H_3PO_4$ electrolytes. After nanotube formation, nanotube layer was removed by ultrasonic cleaning. PEO-treatment was carried out at 280V for 3 minutes in the electrolytic solution containing the bioactive substance (Mg, Zn, Mn, Sr, and Si). The surface of Ti-6Al-4V alloy was observed by field emission scanning electron microscopy (FE-SEM, S-4800 Hitachi, Japan). An energy dispersive X-ray spectrometer (EDS, Inca program, Oxford, UK) was used to analyze the spectra of physiologically active Si, Mn, Mg, Zn, and Sr ions. The PEO film formed on the Ti-6Al-4V alloy surface was characterized using an X-ray diffractometer (TF-XRD, X'pert Philips, Netherlands). It is confirmed that bioactive ions play an essential role in the normal bone growth and metabolism of the human skeletal tissues.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.461-468
• /
• 2012

This study focuses on the difference of photocatalytic activity depending on crystal structure type of nanoparticles ($TiO_2$) and nanotubes (TNT). The photodecomposition of 2-chlorophenol on the synthesized $TiO_2$, Sn-impregnated $TiO_2$, TNT, and Snimpregnated TNT were evaluated. The characteristics of the synthesized photocatalyts, TNT, Sn/TNT, $TiO_2$, and Sn/$TiO_2$ were analyzed by X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV-Visible spectroscopy (UV-Vis), and cyclic voltammeter (CV). The water-suspended 2-chlorophenol photodegradation over $TiO_2$ (anatase structure) catalyst was better than that over pure TNT. Particularly, the water-suspended 2-chlorophenol of 10 ppm was perfectly decomposed within 4 h over Sn/$TiO_2$ photocatalyst.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.1
• /
• pp.35-42
• /
• 2005

Aligned multi-wall carbon nanotubes (MWNTs) were synthesized through the catalytic decomposition of hydrocarbons in a quartz tube reactor. In this study, we investigated the influence of gas flow rate of feedstock on the structure and growth rate of vertically aligned carbon nanotubes produced by the floating catalyst method. As the flow rate of feedstock increased, the nanotube diameter became smaller and the length became longer. Although the growth rate also increased with the raise of flow rate, the optimum flow rate of feedstock existed for the crystallinity of carbon nanotubes.

• Korean Journal of Materials Research
• /
• v.17 no.3
• /
• pp.173-178
• /
• 2007

Carbon nanotube cathodes(CNT cathodes) with a trench structure similar to gated structure of triode-type cathode were fabricated by a screen printing method using multi-walled carbon nanotubes. The effects of surface treatments on CNT cathodes were investigated for high efficiency field emission displays(FEDs). A liquid method easily removed the organic residue and protruded the CNTs. Field emission properties were measured by using a diode-type mode. The liquid method produced a turn-on field of $1.4V/{\mu}m$. The emission current density was measured about $3.1mA/cm^{2}$ at the electric field of $3V/{\mu}m$. The liquid method showed a high potential applicable to the surface treatment for triode-type FEDs.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.3 s.192
• /
• pp.134-139
• /
• 2007

We report the suspension of individual multi-walled carbon nanotubes (MWNTs) from the bottom substrate using deep trench electrodes that were fabricated using optical lithography. During drying of the solution in dielectrophoretic assembly, the capillary force pulls the MWNT toward the bottom substrate, and it then remains as a deformed structure adhering to the bottom substrate after the solution has dried out. Small-diameter MWNTs cannot be suspended using thin electrodes with large gaps, but large-diameter MWNTs can be suspended using thicker electrodes. We present the statistical experimental results for successful suspension, as well as the feasible conditions for a MWNT suspension based on a theoretical approach.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.5
• /
• pp.1635-1639
• /
• 2011

An efficient and novel positive charge-doping on the sidewalls of multi-walled carbon nanotubes has been achieved in the presence of tetrahydrofuran as a dopant and Lewis acidic ionic liquids, [bmim]$Sb_nF_{5n+1}$ (n ${\geq}$ 2; bmim = 1-butyl-3-methylimidazolium), as an activator, leaving air-stable derivatives having positively charged sidewalls and the counter anions, [MWCNT$^{y+}$][SbF$_6^-$]$_y$ (MWCNT = multi-walled carbon nanotube). The derivatization took place very fast in one-pot and under mild reaction conditions. The ionic structure enabled a tunable dissolution of the derivatives in various solvents through anion exchange.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1410-1411
• /
• 2011

Tip-type carbon nanotube(CNT) based electron emitters were fabricated by forming a hafnium(Hf) interlayer between the CNT and the substrate. The CNTs were deposited by using the electrophoretic deposition method and thermally treated. No significant change in the microscopic structure of the CNTs, such as the ratio of length to diameter, was observed after the deposition of Hf interlayer and thermal treatment. As compared with the CNT emitter without the Hf-interlayer and thermal treatment, the CNT emitter with the Hf-interlayer and thermal treatment showed noticeably improved electron-emission properties due to the enhanced adhesion.