• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 추계학술발표대회 논문집
• /
• pp.32-37
• /
• 2009

An energy loss through the window system occupies about 10 to 30 percent on energy consumption of the whole building. That is the reason, several elements for a building composition of window system are the weakest from the heat. Insulation performance increases for the reducing heat loss. Heat transfer through the window system that is reducing heat transfer through conduction, convection and radiation. Insulation performance reinforcement methods classify improving heat specific quality of window system and improving efficiency of whole window system. The most application method among each methods is reducing emission ratio of the window system(Low-E glass), increasing a number of glazing(multiple window) and a method of vacuuming between glazing and glazing. Therefore this study is investigated a sort of glazing and specific character, U-value calculation with changing glazing thickness and calculation of temperature distribution and U-value with a glazing charging gas kind from double glazing. For a conclusion, an aspect of U-value figure at the smallest value case of vacuum glazing with Low-E coating. That means insulation efficiency is the best advantage during a building plan selecting vacuum glazing with Low-E coating for a energy saving aspect. In this way, U-value become different the number of glazing, coating whether or not and selecting injection gas. Therefore selecting of glazing is very important after due consideration by a characteristic and use of building and consideration of strong point and weak point.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.51-52
• /
• 2002

We report results on microtribological studies of chemically grafted nanoscale polymer layers of different architecture with thickness below 30 nm. We have fabricated the molecular lubrication coatings from elastomeric tri-block copolymers and tested two different designs of corresponding nanocomposite coatings. We observed a significant reduction of friction forces and an increase of the wear stability when a minute amount of oil was trapped within the grafted polymer layer. These polymer gel layers exhibited a very steady friction response and a small value of the coefficient of friction as compared to the initial polymer coating. A polymer 'triplex' coating has been formed by a multiple grafting technique. The unique design of this layer Includes a hard-soft-hard architecture with a compliant rubber interlayer mediating localized stresses transferred through the topmost hard layer. This architecture provides a non-linear mechanical response under a normal compression stress and allows additional dissipation of mechanical energy via the elastic rubber interlayer.

• 한국전기전자재료학회논문지
• /
• 제27권6호
• /
• pp.407-416
• /
• 2014

Five factors are identified, which affect the performance of optical filter: 1) type of optical glass, 2) existence of Fe, 3) photo pic coating type, 4) coating form, and 5) coating thickness. If we consider all the levels of five factors, there are 360 possible candidates. We determined five evaluation criteria, which can be used to evaluate possible candidates. For the performance measures we selected white-state avearge voltage, black-state average voltage, and black-state error rate. And we added economic criterion and quality and maintenance criterion. Through the two-step statistical analysis of white-state avearge voltage, black-state average voltage, and black-state error rates, we selected final four candidates. Based on the five criteria we finally determined optimal optical filter using AHP.

• 한국정보통신학회논문지
• /
• 제19권6호
• /
• pp.1283-1288
• /
• 2015

일반적으로 암호연산이 수행되는 IC 칩 회로는 강한 전자기 신호를 외부로 방사시키는 경향이 있다. 암호 칩 근방에서 루프 안테나와 같은 전력 수집 계측 장비를 활용하면 계측된 전자기 신호에 의해 암호 키의 동정이 가능하다. 이와 같은 비침투형 공격에 대응하기 위한 한 방법으로서 IC 칩 외부로 방사되는 전자기 신호를 억압하기 위해 칩 상부에 다중 유전체 슬래브 구조를 가지도록 구성하는 방법을 도입하였다. 다중 유전체 슬래브는 Bragg 반사특성을 가지도록 적절하게 구성하여 구현하였고 반사응답 특성을 구하여 그 유효성을 검증하였다. 실험결과로서 유전체 코팅의 두께는 2mm로서 수직 입사파에 대한 반사응답 특성은 91% 수준을 달성하였다.

• 한국광학회지
• /
• 제14권3호
• /
• pp.286-291
• /
• 2003

광대역 이득 특성을 얻기 위한 InGaAsP-InP 응력보상 비대칭 다중 양자우물(Asymmetric Multiple Quantum Well, AMQW) 구조를 성장하고, Ridge Waveguide Laser Diodes(RWG-LDs)를 제작하였다. 제작 후 소자의 동작변수와 모드 이득을 측정하였으며, 얻어진 결과를 비교, 분석하였다. 외부 공진기형 구조에서 넓고 평탄한 이득특성을 얻기 위해 한쪽 단면에 Anti-Reflection(AR) 코팅을 수행하여 AR coated AMQW RWG LD의 이득특성을 분석하였다.

• 펄프종이기술
• /
• 제40권5호
• /
• pp.60-69
• /
• 2008

The principal reasons for applying a pigment coating to paper are to improve appearance and printability. The pigment coating provides a surface that is more uniform and more receptive to printing ink than are the uncoated fibers and, in turn, both facilitates the printing process and enhances the graphic reproduction. The improvement in print quality is readily apparent, especially in image areas or when multiple colors are involved. Although pigment coating of paper is to improve the printability, coated paper is not completely free from printing defects. Actually there are a number printing defects that are observed only with the coated papers. Among the printing defects that are commonly observed for coated papers, print mottle during multi-color offset printing is one of the most concerned defects, and it appears not only on solid tone area but also half dot print area. There are four main causes of print mottle ranging from printing inks, dampening solution, paper, and printing press or its operation. These indicates that almost every factors associated with lithographic printing can cause print mottle. Among these variation of paper quality influences most significantly on print mottle problems in multicolor offset printing, and this indicates that paper is most often to be blamed for its product deficiency as far as print mottle problems are concerned. Furthermore, most of the print mottle problems associated with paper is observed when coated papers are printed. Uncoated papers rarely show mottling problems. This indicates that print mottle is the most serious quality problems of coated paper products. Overcoming the print mottle is becoming more difficult because the operating speeds of coating and printing machines are increasing, coating weights are decreasing, and the demands on high-quality printing are increasing. Print mottle in offset printing is caused by (a) nonuniform back trap of ink caused by a nonuniform rate of ink drying, referred as "back trap mottle, and (b) nonuniform absorption of the dampening solution. Furthermore, both forms of print mottle have some relationship to the structure of the coated layer. The surest way of eliminating ink mottling is to eliminate unevenness in the base paper. Coating solutions, often easier to put into practice, should, however, be considered. In this paper the principal factors influencing print mottle of coated papers will be discussed. Especially the importance of base paper roughness, binder migration, even consolidation of coating layers, control of the drying rate, types of binders, etc. will be described.

• Journal of Korean Neurosurgical Society
• /
• 제30권7호
• /
• pp.891-895
• /
• 2001

Objective : Although surgical clipping of intracranial aneurysm is the definite method of treatment, there remains a small number of patients in whom surgical clipping is not technically possible. In such difficult cases, surgeon has to consider other therapeutic alternatives. In this report, we analyze our aneurysmal cases treated by wrapping and coating method and evaluate their surgical outcome and follow-up results. Method : Among the total of 877 patients operated from 1990 to 1999 for intracranial aneurysms at our hospital, 40 cases(4.6%) were treated by wrapping and coating method. They included 24 cases of single ruptured aneurysms and 16 with unruptured ones in multiple aneurysms. Wrapping with temporalis muscle and/or muslin gauze and coating with bioadhesive agent such as fibrin glue were performed. Result : Wrapping and coating method was performed mostly to the anterior communicating artery aneurysm (35%), and mostly because of the broad-based neck of an aneurysm(43%). At the time of discharge, 30 out of 40 patients(80%) showed favourable outcome and three cases died. The patients were monitored for average of 37 months(3-75 months). Among 24 cases with single ruptured aneurysm, 4 cases(17%) had early rebleeding within 6 months from the initial hemorrhage, and such rebleeding occurred within the first postoperative month in 3 cases. However, there was no rebleeding after the 6 months. Among 16 patients whose aneurysms were unruptured ones, none of them showed bleeding episode. Conclusion : It seems likely that the wrapping and coating method would be some help to prevent the rebleeding of an intracranial aneurysm. In order to obtain more accurate results regarding the efficacy of such method, it will be necessary to perform a multi-center study for longer follow-up periods and various wrapping and coating materials.

• 한국분말재료학회지
• /
• 제25권1호
• /
• pp.60-68
• /
• 2018

The design and fabrication of photoelectrochemical (PEC) electrodes for efficient water splitting is important for developing a sustainable hydrogen evolution system. Among various development approaches for PEC electrodes, the chemical vapor deposition method of atomic layer deposition (ALD), based on self-limiting surface reactions, has attracted attention because it allows precise thickness and composition control as well as conformal coating on various substrates. In this study, recent research progress in improving PEC performance using ALD coating methods is discussed, including 3D and heterojunction-structured PEC electrodes, ALD coatings of noble metals, and the use of sulfide materials as co-catalysts. The enhanced long-term stability of PEC cells by ALD-deposited protecting layers is also reviewed. ALD provides multiple routes to develop improved hydrogen evolution PEC cells.

• Corrosion Science and Technology
• /
• 제2권2호
• /
• pp.102-108
• /
• 2003

The surface treatments. Chrome/Manganese and Modified Chrome Pickle, that are treated to improve the anti-corrosion property which is needed to increased the probability of prototype product enabled the sand cast Magnesium test specimens to have better corrosion resistance than non-treated one. Sand cast Magnesium specimens which was treated only with chemical conversion coating had same corrosion resistance with the Steel specimens plated by Zinc, and the another one that had the finishing treatment(painting) worked on the chemical surface treatment had the corrosion resistance property to meet to FPO-3 requirement. We also investigated the multiple finishing system(chemical surface treatment + 3 coating) to test the severe condition that magnesium should to endure.

• 한국전기전자재료학회논문지
• /
• 제21권9호
• /
• pp.783-788
• /
• 2008

We suggest a CNT-based gas sensor for breath alcohol measurement. The sensor was composed of single-walled carbon nanotubes (SWCNTs) thin film on flexible PES (polyethersulfone) substrate, and the SWCNTs thin film was formed by multiple spray-coating with SWCNTs solution which was well-dispersed, highly controlled and functionalized in ethanol solvent. In this work, three types of SWCNTs thin films were deposited with changes in the number of spray-coatings to 20, 40 and 60 times in order to compare electrical response properties of the SWCNTs thin films. from the fabricated sensors, conductance and capacitance responses were measured and discussed. Alcohol gas sensors have been commercialized widely as gauge for breath alcohol measurement which is applicable to checking whether car drivers are drinking-driving or not. Our alcohol gas sensors showed good sensitivity and linearity even at room temperature.