• Journal of Power Electronics
• /
• v.17 no.2
• /
• pp.464-475
• /
• 2017

This study examines a P+multi resonant-based voltage control for voltage harmonics compensation under the islanded mode of a microgrid. In islanded mode, the inverter is defined as a voltage source to supply the full local load demand without the connection to the grid. On the other hand, the output voltage waveform is distorted by the negative and zero sequence components and current harmonics due to the unbalanced and nonlinear loads. In this paper, the P+multi resonant controller is used to compensate for the voltage harmonics. The gain tuning method is assessed by the tendency analysis of the controller as the variation of gain. In addition, this study analyzes the slight voltage magnitude drop due to the practical form of the P+multi resonant and proposes a counter method to solve this problem by adding the PI-based voltage restoration method. The proposed P+multi resonant controller to compensate for the voltage harmonics is verified through the PSIM simulation and experimental results.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.1
• /
• pp.36-42
• /
• 2007

A low-power compact driver for multistandard physical layer is presented. The proposed driver achieves low power and small area through the voltage-mode driver with trans-impedance configuration and the novel hybrid driver,. In the voltage-mode driver, a trans-impedance configuration alleviates the problem of limited common-mode range of error amplifiers and the area and power overhead due to pre-amplifier. For a standard with extended output swing, only current sources are added in parallel with the voltage-mode driver, which is named a 'hybrid driver'. The hybrid architecture not only increases output swing but reduces overall driver area. The overall driver occupies $0.14mm^2$. Power consumptions under 3.3-V supply are 24.5 mW for the voltage-mode driver and 44.5 mW for the hybrid driver.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.2
• /
• pp.104-109
• /
• 2009

At a lower supply voltage, voltage-mode drivers draw less current than current-mode drivers. In this paper, we newly propose a voltage-mode driver with an additional current path that reduces the output voltage swing without the need for complicated additional circuitry, compared to conventional voltage-mode drivers. The prototype driver is fabriccated in a 0.13-$^{\mu}m$ CMOS technology and used to transmit data streams at the rate of 2.5 Gb/s. Deemphasis is also implemented for the compensation of channel attenuation. With a 1.2-V supply, it dissipates 8.0 mA for a 400-mV output voltage swing.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.1
• /
• pp.88-95
• /
• 2011

In this paper, a new standby-mode control method for multiple output switching-mode power-supply is suggested, which uses the control signal of the feedback compensator of the inner loop in the linear voltage regulator located at the transformer secondary side, as the load current information. Conventional method has a problem that standby mode occurs depending only on the load condition of the main controller output, which makes the other secondary side output very inaccurate by burst mode operation. The proposed method detects all the load current information and operates in burst mode only when the all of them are light load condition. Minimum of the additional components are required for the implementation of the proposed method because the load information is obtained from the existing feedback circuit of the post-stage linear regulator. In this paper, the operating principles of the proposed standby-mode circuit are presented with an numerical analysis, and are verified by 25W hardware prototype implementation.

• Current Photovoltaic Research
• /
• v.7 no.3
• /
• pp.71-75
• /
• 2019

Solar energy is one of the renewable energy sources. It can respond to expanding energy demand. A solar cell module is designed to have a durability that can be developed over a long period of 25 years to be installed outdoors and perform like a stable power supply. We need Standard Test Condition (STC)-based power output data before and after testing to measure the power output of existing modules. The modules are shown to reduce power output by comparing data before and after outdoor experiments regardless of whether they are indoor or outdoor. It is easy to compare the power output quantities through the module simulator in the indoor. However, it takes a lot of testing time and costs to compare the power output on outdoor in the case of a high number of modules and distance from the module simulator. It can save time and costs if we can check the power output using the data in outdoor. We have used the long-term outdoor test to find the elements out that corresponds to the reductions in power output quantities. We have conducted research that matched the actual and the tests.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.913-914
• /
• 2006

In industrial field, electric fork-lift has been mainly powered by batteries which are varied from DC 36V to 80V. Operating electric fork-lift truck depends on stable electric power supplies which are ensured by using Switched Mode Power Supply (SMPS). This paper presents design of SMPS for stable electric power supply. The SMPS has much strength such as high effectiveness, low cost and high stability of output voltage. At the same time, SMPS is small and multi output and has simple design of circuit.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.41-44
• /
• 1999

The main purpose of the UPS is to supply independent and stable power to connected equipment. In installing and operating the UPS system, songle module, three phase UPS in more benefit than multi module, songle phase UPS in the point of volume and cost. However, when supplying Rectifier with output power form three phase UPS, by connecting auto-transformer, occurred harmonic and ripple current makes output filter damaged and leads to nonlinear current coasted by unbalance load. Therefor, in this paper the aim of concentring compound-wound transformer and harmonic filter is supplying liner current by reducing harmonic and ripple current and improving unbalance in voltage and distortion in current wave.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.6
• /
• pp.699-706
• /
• 2015

A previous adapter have a single-ouput, however, a demand of a multi-output adapter increase in the recent industrial site. In order to satisfy the demand, in this research, we implement a programmable high efficiency multi-output adapter. The basic structure of the adapter introduced in this paper is a sort of flyback. The way for producing the reference voltage of the adapter proposed is similar to the way in the general flyback implemented with TL431. In addition to the basic concept of the design, however, we introduce a digital variable resistor, AD5246BKSZ10-RL7 and a microcontroller for changing a programmable multi-output. It makes output be variable that the digital variable resistor change the reference voltage of the adapter by order of the microcontroller. The adapter output voltage is controllable in the range of 20V by the user, and the power efficiency is proven to be 85%.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1262-1264
• /
• 2003

The author Present a modified multiloop algorithm including feedforward for controlling a 45kW step down chopper in the power supply of Maglev. The control law for the duty cycle consists of three terms. The first is the feedforward term which compensates for variations in the input voltage. The second term consists of the difference between the slowly moving inductor current and output current. The third term consists of proportional and integral terms involving the perturbation in the output voltage. This perturvation is derived by subtracting the desired output voltage from the actual output voltage. The proportional and integral action stabilizes the system and minimizes output voltage error. To verify the validity of the proposed multiloop controller, simulation study was tried using Matlab/sirnulink.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.133-135
• /
• 2004

As a result of the recent advances in magnetic materials, the Magnetic Amplifier(Magamp) technique is one of the reliable and cost-effective postregulation method for multiple-output power supply. This is true for high-current postregulated output since at highter output current the efficiency of linear postregulation is unacceptably low, while the complexity of more efficient switch mode postregulator is associated with a significant cost. Magamp have some advantages of higher power density, simple control circuit, good regulation, high frequency and high performance. In this paper, Operation principle of proposed approach and a performance of magamp control circuit with TL431 is described. The comparative analysis of magamp circuit and buck regulator circuit with 20W load condition is conducted. Experimental verifications on multi-output flyback converter are conducted. Simulations and experimental results show that the proposed approach is efficiency and voltage regulation of the auxiliary output is excellent.