• Design & Manufacturing
• /
• 제13권2호
• /
• pp.49-53
• /
• 2019

The temperature distribution and lifetime of molds were predicted by computer simulation analysis with various spraying and blowing process of high pressure die casting. After varying the spraying angle and time, the mold temperature, heat exchange and mold life were predicted. As the spraying angle increases, the maximum temperature of the mold decreases, which is because the spraying area increases and the heat exchange with the mold increases. Heat exchange occurs more actively in the blowing process than in the spraying process. This is because the cooling is not performed due to the steam generation. When the spraying angle is 50 degree, the minimum life of the mold is analyzed 200 times. After adjusting the blowing time from 5s to 3s, the minimum lifetime of the mold has been increased almost twice.

• 소성∙가공
• /
• 제30권3호
• /
• pp.149-156
• /
• 2021

Fine blanking is a high-precision process combining principles of metal stamping and cold forming. Unlike conventional metal stamping, fine blanking uses a special triple action such as V-ring force, counter force, shearing force. This study performed the effect of pocket-shaped compression molding on the mold life of the fine blanking using the 7.4mm thick SM45C material. In order to determine the lifespan of the punch and die in the fine blanking molds, a trial mold was manufactured and various punch materials were selected to perform the mold life test. A study on the life of a fine blanking mold by applying a thick plate material was experimentally performed through a mold test.

• 소성∙가공
• /
• 제32권6호
• /
• pp.335-343
• /
• 2023

Spur Gear parts for automobile actuators using existing former forging technology were produced in a total of three processes on a former forging machine. However, in order to improve cost increase due to frequent mold breakage, Spur Gear parts were designed and manufactured in the cold forging process after forming the preform through former forging. In other words, in the existing former forging mold, product seating defects occurred due to horizontal movement, resulting in many product defects and mold damage, so there was an urgent need to improve mold life and product defects. In order to improve this, we tried to improve the mold life by improving the existing 3 former forging processes to a former forging process and 2 cold forging processes. Therefore, We developed Spur Gear parts for automobile actuators were developed by applying precision cold forging technology through a former forging process and 2 cold forging processes to improve mold life.

• 펄프종이기술
• /
• 제48권1호
• /
• pp.43-52
• /
• 2016

The coniferous fallen leaf is one of the major forestry residues. Since the coniferous fallen leaf would not be easily decayed, the large amount of the coniferous fallen leaves in forestry could be the source of forest fire. The applicability of the fallen leaves to the pulp mold were evaluated for developing new utilization of coniferous fallen leaves. The morphological properties and the chemical composition of the fallen leaves of Pinus densiflora and Pinus koraiensis were evaluated by the comparison with those of fresh leaves. The applicability of the coniferous fallen leaves to the pulp mold and the effects on the pulp mold properties including the scent diffusion were investigated. The fallen leaves showed the shrunk structure by losing the hot water extract component, which leaded to better grinding properties than that of fresh leaves. The pulp mold with fallen leaves showed higher strength properties than the pulp mold with fresh leaves. Although the scent of the pulp mold with fresh leaves was stronger, the pulp mold with fallen leaves had coniferous scent too. The application of fallen leaves to pulp mold for the functional properties could be possible by improving the mechanical properties and the scent lasting treatments.

• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.122-129
• /
• 2004

In plastic working, as working becomes speedy, automatic and working condition deteriorates, the increase of forging working has been remarkable. Therefore, we need the estimation of mold lift in detail, in order to counterplan of effective mold life extension. In this study, on the SKH51, mold steel which is forged by cold working and the KCW1, tool steel of low alloy, we estimated mold life on the base of FEM analysis and investigated mold lift by low cycle fatigue test. Also, this paper suggested a new method of estimation of mold lift.

• 한국생산제조학회지
• /
• 제22권3_1spc호
• /
• pp.504-508
• /
• 2013

This paper describes in detail the life prediction models and simulations of thermal fatigue under different mold compounds and chip sizes for wafer-level embedded SiP. Three-dimensional finite element models are built to simulate the viscoplastic behaviors for various mold compounds and chip sizes. In particular, the bonding parts between a mold and silicon nitride (Si3N4) are carefully modeled, and the strain distributions are studied. Three different chip sizes are used, and the effects of the mold compounds are observed. Through the numerical studies, it is found that type-C, which has a relatively lower Young's modulus and higher CTE, has a better fatigue life than the other mold compounds. In addition, the $4{\times}4$ chip has a shorter life than the $6{\times}6$ and $8{\times}8$ chips.

• 펄프종이기술
• /
• 제48권3호
• /
• pp.66-72
• /
• 2016

The applicability of rice husk fiber as a raw material for eco-friendly pulp mold was evaluated in this study. The higher demand of environmental friendly packaging material resulted in the more interest for the natural fiber based pulp mold. The rice husk which is an abundant agricultural byproduct in Asia could be defiberized by an alkaline digestion process. The changes in the pulp mold making process and the properties of pulp mold by the addition of the rice husk were investigated. The addition of rice husk fiber to the pulp mold made with OCC or UBKP resulted in the increase in drainage at the pulp mold forming process. In case of UBKP pulp mold, the addition of rice husk fiber increased the drying efficiency after pulp mold forming since the structure of pulp mold became more bulkier by the addition of the rice husk fiber. Those results showed the rice husk fiber could be applied to the pulp mold manufacturing as one of the eco-friendly natural fiber resources.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.373-376
• /
• 2000

Recently, the life cycle of products is rapidly shortened and then the W s a l of the used mold applied in development of a product is a difficult things. In this study, we proposed a feasibility of the recycling mold base by analyzing of the existing standard mold base. And we developed a D/B program to promote the mold design capability with CAD. Also, we confirmed the possibility of recycling mold base by testing of a used automobile lamp mold.

• 펄프종이기술
• /
• 제48권1호
• /
• pp.67-74
• /
• 2016

The demand of environmental friendly packaging materials such as pulp mold has been increased. The application of the oil palm biomass, EFB (Empty Fruit Bunch) fiber as natural raw materials to the pulp mold could increase the usability of the pulp mold by the reduced production cost brought from the relatively low cost of EFB. The effects of the EFB(Empty Fruit Bunch) fibers on the properties of pulp mold and on the process efficiency were evaluated in this study. The pulp mold samples were prepared with mixture ONP (Old news paper) and EFB by using laboratory wet pulp molder. The changes in the drying efficiency were measured with the changes in the solid contents of pulp mold samples during drying process. The efficiency of the surface coating treatment on the pulp mold depending on the condition of the pulp mold samples were also evaluated in order to improve the water resistance properties of pulp mold. The addition of EFB increased the drying efficiency by providing the bulkier structure and the higher water contact angle, which indicated the better water resistance properties. The water resistance were improved by the surface coating treatments and the application of surface coating on the pulp mold at the higher moisture contents resulted in the higher improvement in the water resistance. The bulkier structure originated from the application of EFB fiber reduced the effects of the surface coating, which could be overcome by the control of surface coating process.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2009년도 정보통신설비 학술대회
• /
• pp.391-394
• /
• 2009

In this paper, achieved rise temperature distribution about degradation phenomenon of 2 MVA distribution mold transformer using finite element method (FEM). Usually, life of transformer is depended on temperature distribution of specification region than thermal special quality of transformer interior. Specially, life of transformer by decline of dielectric strength decreases rapidly in case rise by strangeness transformer interior hot spot temperature value permits. Because calculating high-voltage winding and low-voltage winding of mold transformer and Joule's loss of core for improvement these life, forecasted heat source, and high-voltage winding and low-voltage winding of mold transformer and rise temperature distribution of core for supply of electric power and temperature distribution of highest point on the basis of the result Also, calculated temperature rise limit of mold transformer and permission maximum temperature using analysis by electron miracle heat source alculate and forecasted rise temperature distribution by heat source of thermal analysis with calculated result.