• 한국연소학회지
• /
• 제17권1호
• /
• pp.12-21
• /
• 2012

Simultaneous measurements of oxygen concentration and temperature using diode laser in the combustion environment are successfully accomplished. A single DFB type diode laser of 760 nm line centre frequency is used and the scanned-wavelength direct absorption spectroscopy method and wavelength modulation spectroscopy method are applied to measure absorption signals below 793 K temperature region. The experimental results show that oxygen concentration are measured within 1% accuracy and temperature are measured within 5% accuracy. This new method of simultaneous measurements of concentration and temperature with a single diode laser shows a great promise.

• 전자공학회논문지D
• /
• 제35D권5호
• /
• pp.69-79
• /
• 1998

In this paper, we have proposed a new row signal modulation method in order to display multi-gray image using super-twisted nematic liquid crystal display (STN-LCD), which has no complex computation, high selection ratio, and low driving voltage. By the proposed method, we have implemented a 320*240, 8-gray video-rate STN-LCD. For achieving a video-rate STN-LCD, 6 lines are selected at a time. Each row line is selected 8 times by equally distributed pulses throughout one frame. As a result, we can get 8 gray, video-rate image. The repetive horizontal pattern and the filckering was analyzed and the improvements have been presented.

• 한국통신학회논문지
• /
• 제21권4호
• /
• pp.1077-1088
• /
• 1996

In this paper, we propose a new method to analyze the performance degradation by timing jitters in the receivers of intensity modulation/direct detection digital optical communication systems where pulse-shaping filters are used to minimize intersymbol interference. The results obtained from the proposed analytical method show that conventional analytical methods underestimate the influence of timing jitters on the receiver performance. Using the proposed anlaytical method, we derive an analytic equation for approximated power penalty due to timing itters and obtain an exact power penalty by numerical analyses. Assuming Gaussian or uniform probability density function for timing jitters, we also show that assumption of Gaussian distribution for timing jitters yields more performance degration than that of uniform distribution.

• Journal of Power Electronics
• /
• 제10권1호
• /
• pp.51-57
• /
• 2010

This paper proposes a new random switching strategy using a DSP TMS320F2812 to reduce the harmonics spectra of single phase switched reluctance motors. The proposed method combines the random turn-on/off angle technique and the random pulse width modulation technique. A harmonic spread factor (HSF) is used to evaluate the random modulation scheme. In order to confirm the effectiveness of the proposed method an experiment was conducted. The experimental results show that the harmonic intensity of the output voltage for the proposed method is better than that for conventional methods.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.1076-1079
• /
• 1997

A new 3D micromachining method, called Hole Area Modulation(HAM), has been introduced and experimentally confirmed its feasibility. In this method, information on the depth of machining is converted to the sizes of small holes in the mask. The machining is carried out with a simple 2D movement of the workpiece. This method can be applied for machining various kinds of microcavities in various materials. In this paper, a mathematical model for excimer laser micromachining based on HAM and also determination of the optimal laser ablation conditions(width, Hole radius, step size, path, etc.) is completed by employing using Genetic Algorithm(GA).

• 동력기계공학회지
• /
• 제3권2호
• /
• pp.70-78
• /
• 1999

The vector controlled induction motor(I.M) with speed sensor has been widely used for variable speed drive systems. In these application fileds, speed sensorless control are expected strongly to progress reliability, simplicity and cost performance of I.M and to expand its application part. This paper describes a novel speed sensorless control method of I.M based on feedforward quick torque response control technique. Especially, this paper aimed at the realization of sensorless control in the very low speed region, The proposed method can be formulated simply from a motor circuit equation and conducted easily by detecting primary motor currents and a voltage command at every sampling time. Throughout some results of numerical simulations with the assumption of using a pulse width modulation(PWM) voltage source inverter, the validity of the method was successfully confirmed.

• 한국정밀공학회지
• /
• 제15권1호
• /
• pp.109-116
• /
• 1998

This paper is concerned with effective operating method of pneumatic on-off valves for improving position control accuracy, valve life-time and position settling time using modified pulse width modulation with dead-zone (MPWMD). The pneumatic system using on-off valves has advantage of simple construction and low cost compared with a system with servo-valves. The performance of the proposed control method is investigated experimentally for the position control of a pneumatic cylinder using on-off valves. Experimental results show that the proposed algorithm for valve operation can be used to obtain fast and accurate position control compared to the conventional PWMD algorithm. It is also shown that the use of the proposed MPWMD algorithm for the position control significantly reduces the number of valve switching and noise.

• 대한기계학회논문집
• /
• 제18권10호
• /
• pp.2523-2532
• /
• 1994

In this paper, active noise control is performed in a duct system using the periodic pulse train which corresponds to the periodic component of noise source as a reference signal. Control algorithm applied in this study is possible to eliminate the acoustic feedback which occurs in the conventional filtered-x and filtered-u LMS algorithm by using electrical reference signal and has the fast adaptation speed with low filter orders by using synchronous sampling method is discussed via computer simulations and experiments of case studies such as frequency modulation, amplitude modulation and frequency differency between source signal and reference signal.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.132-137
• /
• 2000

A complete theoretical treatment of the photothermal displacement technique has been performed for thermal diffusivity measurement in solid materials. The influence of parameters - radius and modulation frequency of pump beam and thickness of material - on the phase lag was studied. The phase decreases up to a certain position, then starts to increase and does have an asymptotic value. The position, where phase has the minimum value, is a function of thermal diffusion length thickness of sample, and radius of pump beam. A new method based on minimum phase lag is described to determine the thermal diffusivity of solid material.

• Journal of Communications and Networks
• /
• 제9권4호
• /
• pp.482-489
• /
• 2007

In this paper, two frequency domain signal processing techniques for pulse shape modulation(PSM) ultra wideband(UWB) systems are presented. Firstly, orthogonal detection of UWB PSM Hermite pulses in frequency domain is addressed. It is important because time domain detection by correlation-based receivers is severely degraded by many sources of distortion. Pulse-shape, the information conveying signal characteristic, is deformed by AWGN and shape-destructive addition of multiple paths from the propagation channel. Additionally, because of the short nature of UWB pulses, timing mismatches and synchronism degrade the performance of PSM UWB communication systems. In this paper, frequency domain orthogonality of the Hermite pulses is exploited to propose an alternative detection method, which makes possible efficient detection of PSM in dense multipath channel environments. Secondly, a ranging method employing the Cepstrum algorithm is proposed. This method is partly processed in the frequency domain and can be implemented without additional hardware complexity in the terminal.