• Journal of Animal Environmental Science
• /
• v.6 no.3
• /
• pp.133-140
• /
• 2000

This study was carried out to determine a suitable mixing rate to utilize the PDF as a bedding materials at the pigpens and investigate the effect of substitute processed dustproof fly-ash(PDF) on the odor. In proportion to the increase of substitute rate of the PDF, the utilizable period was extended, and there was a little change of the moisture in the bedding materials. At all the treatment of PDF, there was the significant effect on the maggots and parasites but it didn\`t hinder in the biodegradation. According to highly mixing rate, PDF decreased in the noxious gas ($NH_3$ and $H_2$S) emission. In conclusion, the mixing rate of 30% or above this substituted level will increase replacement terms, and reduce the sawdust cost and the pollutions of breed pigs.

• Advances in concrete construction
• /
• v.10 no.5
• /
• pp.381-391
• /
• 2020

This study aimed to develop reference materials (RMs) for mortar that can simulate the initial flow characteristics with constant quality over a long period. Through the previous research on the development of RMs for cement paste, the combination of limestone, glycerol, and water was used as the basic matrix for developing RMs for mortar in this study. In addition, glass beads of three particle sizes (0.5, 1.0, and 2.0 mm) and ISO standard sand were selected as tentative candidates to derive fine aggregate substitutes. The mixture of glass beads could simulate the initial flow characteristics of mortar, but under the same mixing ratio, replicates showed an unstable tendency to indicate inconsistent values due to the generation of electrostatic properties between materials and equipment. On the other hand, the mixture using ISO standard Sand not only simulates the constant flow characteristics for a long period of time, but also shows stable results with little error in replicates. Therefore, limestone, glycerol, ISO standard sand, and water were finally determined as components that met the required properties of RMs for mortar. The effect of each component on the flow characteristics of RMs was analyzed. It was found that glycerol increased the cohesion between the particles of standard sand, resulting in a constant increase both in the plastic viscosity and yield stress. Both limestone and standard sand had a dominant effect on the yield stress. The relationships between various mortar mixing ratios and the corresponding mixing ratios of RMs were established. In addition, the results of the verification experiment showed that the rheological properties of the RMs obtained through the relationships correlated with various water/cement ratios and the fine aggregate volume fractions of mortar obtained with same manner. In other words, the RMs for mortar developed in this study can be used as standard samples because they can simulate the initial flow characteristics of mortar of various mixing ratios for a long period without any chemical changes.

• Resources Recycling
• /
• v.19 no.1
• /
• pp.27-32
• /
• 2010

To improve electronic conductivity of cathodic active materials of lithium ion battery, carbonaceous materials is usually added. New mixing method of abrasive milling has been investigated in mixing of graphite and $LiCoO_2$ powders. It would be expected that uniform mixing of graphite reduces capacity fading of cathode of lithium battery. Abrasion milled $LiCoO_2$ composite showed the best electrochemical performance as a cathode material with 1 wt% of graphite content, 300 rpm of milling speed, and 10 min of milling time. The improvement of the electrochemical performances such as cycleability and charge/discharge capacity retention would be mainly attributed to increase of the electronic conductivity and/or prevention of the active materials by uniform dispersion and coating of graphite on $LiCoO_2$.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2007.04a
• /
• pp.285-297
• /
• 2007

As the demands of environment protection increase, the pulp mold container is developed to substitute for the plastic cushion materials like EPS(expanded poly styrene). The water-absorbing ratio, tensile strength and compressive strength of pulp mold are important factors to evaluate its shock absorbing characteristics. The study was performed to investigate the effects of the mechanical property changes on the various conditions of temperature and relative humidity for pulp mold containers made of mixed materials on ONP(old newspaper) and OCC(old corrugated container). This study also is evaluated the optimized mixing ratio of materials for making pulp mold by analyzing the changes of physical properties according to a various procured temperature and relative humidity conditions. The results show that the water absorption ratio of sample increased significantly, and tensile strength decreased $20{\sim}30%$, compressive strength decreased $10{\sim}20%$ by increasing relative humidity condition. And the results show that the ONP 50% and OCC 50% was optimized mixing ratio according to the samples.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.19 no.4
• /
• pp.45-59
• /
• 2016

This study introduced wood waste into revegetation base materials for recovery of highway cut slope. The object of this study is to derive the mixing ratio of wood waste, kaoline and silica by conducting a test installation, monitoring, analysis and evaluation. The following items were investigated and analyzed each experimental zone to deduce the mixing ratio of wood waste, kaoline and silica on slope revegetation base materials: the physical and chemical properties of the vegetation base materials, soil-hardness, soil-humidity, collapse and eroded spots, established number of trees, existing species of grass and tree species, vegetation coverage ratio, pest status, and invasion of disturbance species. The revegetation method was evaluated in each experiment zone which had different mixing ratios. As a result, experiment zone C scored 47 points out of 60 as the best revegetation method. However, this result has been derived from just one construction and short-term monitoring. In order to derive the suitable and dependable mixing ratio, conducting an objective revegetation method evaluation and long-term experimenting and monitoring is required.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.18 no.6
• /
• pp.215-226
• /
• 2015

This study introduced food waste into re-vegetation base materials for surface loss recovery of carry-away highway cut slope. The object of this study is to derive the mixing ratio of food waste by conducting a test installation, monitoring, analysis and evaluation for recovery of carry-away highway cut slope. The following items were investigated and analyzed each experimental zone to draw mixing ratio of re-vegetation base materials and food waste : the physical and chemical properties of the vegetation base materials, soil-hardness, soil-humidity, left out and the collapsed point, established number of trees, species richness of grass species and tree species, coverage, pest status, and invasion of disturbance species. The re-vegetation method was evaluated by each experiment zone which has different mixing ratio. As a result, experiment zone A was rated 45 points out of 60 rating points as the best re-vegetation method. However, this study result has been derived from one construction and short-term monitoring. In order to derive the suitable and dependable mixing ratio, conducting an objective re-vegetation method evaluation and long-term experiment and monitoring is required.

• Journal of Theoretical and Applied Mechanics
• /
• v.3 no.1
• /
• pp.45-65
• /
• 2002

A constitutive model on oorthotropic thermo-elasto-viscoplasticity for fiber-reinforced composite materials Is illustrated, and their thermomechanical responses are predicted with the fully-coupled finite element formulation. The unmixing-mixing scheme can be adopted with the multipartite matrix method as the constitutive model. Basic assumptions based upon the composite micromechanics are postulated, and the strain components of thermal expansion due to temperature change are included In the formulation. Also. more than two sets of mechanical variables, which represent the deformation states of multipartite matrix can be introduced arbitrarily. In particular, the unmixing-mixing scheme can be used with any well-known isotropic viscoplastic theory of the matrix material. The scheme unnecessitates the complex processes for developing an orthotropic viscoplastic theory. The governing equations based on fully-coupled thermomechanics are derived with constitutive arrangement by the unmixing-mixing concept. By considering some auxiliary conditions, the Initial-boundary value problem Is completely set up. As a tool of numerical analyses, the finite element method Is used with isoparametric Interpolation fer the displacement and the temperature fields. The equation of mutton and the energy conservation equation are spatially discretized, and then the time marching techniques such as the Newmark method and the Crank-Nicolson technique are applied. To solve the ultimate nonlinear simultaneous equations, a successive iteration algorithm is constructed with subincrementing technique. As a numerical study, a series of analyses are performed with the main focus on the thermomechanical coupling effect in composite materials. The progress of viscoplastic deformation, the stress-strain relation, and the temperature History are careful1y examined when composite laminates are subjected to repeated cyclic loading.

• Korea-Australia Rheology Journal
• /
• v.15 no.4
• /
• pp.197-208
• /
• 2003

Two measures of distributive mixing are examined: the standard deviation $\sigma$ and the maximum error E, among average concentrations of finite-sized samples. Curves of E versus sample size L are easily interpreted in terms of the size and intensity of the worst flaw in the mixture. E(L) is sensitive to the size of this flaw, regardless of the overall size of the mixture. The measures are used to study distributive mixing for time-periodic flows in a rectangular cavity, using the mapping method. Globally chaotic flows display a well-defined asymptotic behavior: E and $\sigma$ decrease exponentially with time, and the curves of E(L) and $\sigma$ (L) achieve a self-similar shape. This behavior is independent of the initial configuration of the fluids. Flows with large islands do not show self-similarity, and the final mixing result is strongly dependent on the initial fluid configuration.

• Journal of the Korean Society of Safety
• /
• v.12 no.2
• /
• pp.133-139
• /
• 1997

Conventional concrete mixing method is to put all of the materials simultaneously into a mixer and mix for a required time. However, recently concrete researchers have reported that mixing sequence iufluences the properties of concrete. This study discusses the influence of mixing sequence and partitioning addition of mixing water. Concrete, by method of partitioning addition of mixing water, was found to have substantially stronger strength than conventional concrete with the same water-cement ratio. This means that a higher strength concrete could be obtained by using “Sand Enveloped with Cement”(S.E.C) mixing technique. Both a high bond strength between cement paste and aggregate, and elimination of bleeding both contribute to improving the strength of S. E. C concrete.

• Resources Recycling
• /
• v.24 no.6
• /
• pp.61-68
• /
• 2015

In this study, the strength properties of NHL based mortar with blending basalt fiber were investigated. In the first step, it was evaluated that physical properties of NHL based mortar according to mixing method of four types of basalt fiber and then mixing method of one type was selected. As a result of assessment, it showed that the physical properties with mixing method of dry blending were better than that of wet blending and mixing method that basalt fiber pre-mixed with NHL for 5 min in a blender was selected and water and aggregate were finally added. Secondly, the investigation of blending fiber length on the compressive and flexural strength for basalt fiber reinforced NHL based mortars was carried out. The compressive strength was decreased with adding fiber, and the flexural strength was increased more than plain mortar. In the case of adding 6 mm fiber, the compressive and flexural strength were improved more than that of others.