• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.24 no.3
• /
• pp.48-54
• /
• 2016

This paper proposes a prediction model of air traffic controller's take-off clearance under mixed mode runway operations. The proposed model has its purpose on the better prediction of the air traffic controller's clearance on take-offs of departure aircraft by considering various factors. For this purpose, support vector machine classification algorithm is used for the proposed model. The proposed model is applied to real air traffic operations to demonstrate its performances.

• International Journal of Highway Engineering
• /
• v.9 no.3
• /
• pp.83-89
• /
• 2007

When allocating traffic signal at the signalized intersection, minimum green time and clearance time for bicyclists should be significantly considered in order to enhance safety aspects to bicyclists when crossing intersections, especially where intersections with exclusive bicycle paths that are physically separated from pedestrians. In this study, field measurements related to bicycle crossing time, including minimum peen time and clearance time, were collected and analyzed according to bicycles crossing types at the signalized intersections where high rate of bicyclists exists. Three types of bicycle crossing are defined as follows 1) stopping: completely stop before crossing (at least one foot on found) 2) riding: crossing with riding bicycle 3) pulling: crossing without riding bicycles. Minimum green time based on pedestrian speeds should be used as crossing time in this case. For bicyclists, speed of bicycle that is applicable to estimate the minimum green time is in the 1.36m/sec($15^{th}$ percentile) to 1.60m/sec($25^{th}$ percentile) range in case of its stopping. Also it is in the 0.75($15^{th}$ percentile) to 0.87($25^{th}$ percentile) range for pulling at crosswalk. In addition, speed of bicycle to consider for calculating the clearance time is in the 2.51m/sec($15^{th}$ percentile) to 2.79m/sec($25^{th}$ percentile). These values also resulted from $15^{th}$ percentile or $25^{th}$ percentile speeds of riding. The results of this study are expected to be supported in traffic signal allocation process, reflecting bicyclists' characteristics.

• Tribology and Lubricants
• /
• v.14 no.3
• /
• pp.87-93
• /
• 1998

Crank pin bearing in two-stroke marine diesel engine is operated under quite severe conditions since the elements are big and heavy and the sliding speed is very slow. Therefore it is very difficult to form oil film. In this paper, two types of bearings with different groove shape are compared. One has circumferential oil groove at lower position and the other has lengthwise oil groove at upper position. Bearing clearance, oil inlet pressure and length to diameter ratio are selected as design parameters. Locus of journal center and minimum oil film thickness are investigated to compare two cases.

• Tribology and Lubricants
• /
• v.12 no.3
• /
• pp.100-106
• /
• 1996

Gerotor pumps and motors are widely used in lubrication and hydraulic actuator systems. Compared with internal gear pumps and motors, they have many advantages. However, the gerotor profiles have not been suff'lciently analyzed theoretically. Therefore, it is very difficult for designer to decide the specifications of the gemtor profiles, and calculation of flow rate and minimum distance of clearance in the contact point of inner and outer rotor is not yet confirmed. In this paper, when we design inner and outer rotor concurently, we have analyzed the gerotor profiles and displayed the calculated results such as flow rate, minimum distance between inner and outer rotor and gerotor profiles.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2018.05a
• /
• pp.285-286
• /
• 2018

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.5
• /
• pp.59-66
• /
• 2010

Korea have experienced a very rapid increase in police-reported collisions between bicycle and motor vehicles over the past decade. Even though cycling accidents are increasing, efforts to make urban areas more accomodating to cyclists are seldom formed. Clearance intervals(including both the yellow change and all-red clearance intervals) at signalized intersections that are of inadequate lengths for bicycles may cause accidents. Data on bicycling speed, acceleration and deceleration were tested and analyzed on the flat. Using the results of the analysis and based on the AASHTO's equation of the bicycle clearance interval, a methodology is got for calculation safe clearance intervals for bicycle riders. The clearance interval call for bicycles will be larger or same than for vehicles because of the speed, acceleration and deceleration difference. Adequate bicycle speed, acceleration and deceleration for korean bicycle users is presented in this paper. It is hoped that traffic engineers to provide safe intersection clearance time for bicycles use the results of this paper.

• Tribology and Lubricants
• /
• v.31 no.5
• /
• pp.205-212
• /
• 2015

In this research, effects of profile changes of stem section of the plunger on the lubrication characteristics of a fuel injection pump (FIP) were evaluated by hydrodynamic lubrication analysis. The clearance between plunger and barrel was divided into two regions, head and stem. The head was not involved in preventing a decrease of fuel oil pressure. So, research efforts were focused on both edges of the plunger’s stem. The two -dimensional Reynolds equation was used to evaluate lubrication characteristics with variations in viscosity, clearance and profile for a laminar, incompressible, unsteady-state flow. Moreover, the equilibrium equation of moment and forces in the vertical and horizontal directions were used to determine the motion of the plunger. The equations were discretized using the finite difference method. Lubrication characteristics of the FIP were investigated by comparing the dimensionless minimum film thickness, or film parameter, which is the ratio of minimum film thickness to surface roughness. Through numerical analyses, we showed that the profile of the lower edge of the stem had no effect on lubrication characteristics, but the profile of the upper edge had a significant influence on lubrication characteristics. In addition, changes in the profile were more effective in improving lubrication characteristics under low viscosity conditions.

• Tribology and Lubricants
• /
• v.33 no.1
• /
• pp.23-30
• /
• 2017

The electric controlled marine diesel engine has fuel pump generating the high pressurized fuel for fuel injection to combustion chamber via a common rail. Fuel pump consists of a cam-roller system. Journal bearing installed between a roller and a cam-roller pin is subjected to fluctuating heavy and instant loads by cam lift. First, Kinematic analysis is carried out to predict bearing loads during one cycle acting on the journal bearing. Second, flexible multi-body dynamic analysis and transient elasto-hydrodynamic(EHD) lubrication analysis for journal bearing considering elastic deformation of cam-roller pin, roller and bearing are conducted using AVL EXCITE/PU software to predict lubrication performance. The clearance ratio and journal groove shape providing lubrication oil are important parameter in bearing design having good performance and can be changed easier than other design parameters such as diameter, width, oil supply pressure and bearing material grade. Generally, journal bearing performance is represented by the minimum oil film thickness(MOFT) and peak oil film pressure(POFP). As well as the traditional design parameters(MOFT, POFP), in this study, temperature rise of lubrication oil is also evaluated through the side leakage flow of supplied oil. By the evaluating MOFT, POFP and temperature rise, the optimum bearing clearance ratio is decided.

• Tribology and Lubricants
• /
• v.34 no.5
• /
• pp.183-190
• /
• 2018

Tilting pad journal bearing is widely used for steam turbines because of its excellent dynamic stability. As the turbine capacity increases, power loss in the bearings becomes a matter of concern. Power loss in tilting pad journal bearings can be reduced by increasing the bearing clearance and reducing the pad arc length. In this study, the tilting pad journal bearing is tested by changing the seal tooth clearance to verify the static characteristics of the bearing. Bearing power loss and bearing metal temperature are evaluated to compare the bearing's performance and reliability for several test cases. The test bearing is a tilting pad journal bearing with 300.62mm inner diameter and 120.00mm active length. The bearing power loss, its metal temperature, and oil film thickness are measured and evaluated based on the rotor's rotational speed, oil flow rate, and bearing load. Test results show that a tilting pad journal bearing with large seal tooth clearance has 40% lower power loss compared with a bearing with a small seal tooth clearance. As the seal tooth clearance is increased, the power loss of the tilting pad journal bearing decreases. However, with respect to the bearing metal temperatures, a detuning point is observed that makes the minimum bearing metal temperature. Moreover, as the seal tooth clearance is increased, the oil film thickness increases due to high viscosity.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.117-121
• /
• 2008

The effect of tip clearance on the performance of a supersonic impulse turbine was investigated experimentally. Test was performed using high pressure air in wide ranges of pressure ratio and rotational speeds. Test revealed that efficiency gradient of the subject turbine at a reference test point was a very low value of 0.05. Turbine efficiency was varied non-linearly with respect to tip clearance. It has been found that efficiency gradient is proportional to the cube of rotational speed at a fixed turbine pressure ratio. It also has been found that efficiency gradient shows its minimum at a reference test pressure ratio irrespective of rotational speeds.