• 공업화학
• /
• 제31권3호
• /
• pp.237-257
• /
• 2020

The role of nano bio-composites precursor to chitosan are innumerable and are known for having different applications in various branches of physical sciences. The application to the sensor development is relatively new, where only few literature works are available to address the specific and critical analysis of nanocomposites in the subject area. The bio-composites are potential and having greater affinity towards the heavy metals and several micro-pollutants hence, perhaps are having wider implications in the low or even trace level detection of the pollutants. The nano-composites could show good selectivity and suitability for the detection of the pollutants as they are found in the complex matrix. However, the greater challenges are associated using the bio-composites, since the biomaterials are prone to be oxidized or reduced at an applied potential and found to be a hinderance for the detection of target pollutants. In addition, the materials could proceed with a series of electrochemical reactions, which could produce different by-products in analytical applications, resulting in several complex phenomena in electrochemical processes. Therefore, this review addresses critically various aspects of an evaluation of nano bio-composite materials in the electrochemical detection of heavy metals and micro-pollutants from aqueous solutions.

• 한국항공우주학회지
• /
• 제41권1호
• /
• pp.17-24
• /
• 2013

본 논문에서는 복합재료의 미시적 파손모드를 고려하는 복합재 파손예측 프로그램을 개발하였다. 개발된 프로그램의 검증을 위하여 원공이 있는 복합재 적층판 시편의 인장시험 및 정적 파손해석을 수행하였다. 먼저 적층각도별 복합재 시편에 대한 인장시험을 통하여 논문에 사용된 재료에 대한 SIFT 허용치를 산출하였고, 미시역학적 모델인 RVE에 대한 유한요소 해석을 통하여 변형률 증폭계수를 결정하였다. 또한 원공이 있는 복합재 적층판 시편에 대한 인장시험을 수행하고, 실험을 통해 얻어진 파손하중 결과를 바탕으로 유한요소 모델에 대하여 정적 파손해석을 수행하였다. 마지막으로 실험결과를 바탕으로 예측된 파손지수 결과를 평가함으로써 개발된 프로그램의 효용성을 검증하였다.

• Composites Research
• /
• 제17권6호
• /
• pp.28-36
• /
• 2004

복합재료의 성형조건과 재료의 변형간의 관계를 규명하기 위해 PVC 포움-직물 복합재료 샌드위치 구조의 성형공정 중 토우 구조의 미소 변형을 고찰하였다. 실험에 사용한 포움은 4가지 밀도를 가지는 PVC 포움이며, 면재로는 탄소섬유게폭시 프리프레그(3k)를 사용하였다. 디지털 현미경과 이미지 분석 도구를 사용하여 직물 복합재료의 굴곡 각과 토우 진폭 등의 토우 파라메터를 측정하여 서로 비교하였다. 성형 중 포움의 변화가 직물 복합재료 구조의 변형에 미치는 영향을 파악하기 위해 세 가지 온도 조건($25^{\circ}C$, $80{\circ}C$, $125^{\circ}C$)에서 포움의 압축 실험을 수행하였다. 복합재료 토우 구조의 현미경 관찰 결과 토우의 미소 변형은 포움의 밀도와 성형 압력에 따라 서로 다른 경향을 나타내었으며. 특히 포움의 변형 거동에 큰 영향을 받는 것을 확인하였다.

• Composites Research
• /
• 제25권4호
• /
• pp.117-125
• /
• 2012

필름 삽입 사출 시편의 휨은 비대칭적인 잔류응력 분포에 기인한다. 비대칭적 잔류응력과 온도 분포는 삽입된 필름 표면의 수직방향으로 지연되는 열 전달에 의해 발생한다. 사출 공정조건 최적화를 통해 필름 삽입 사출 시편의 휨을 억제할 수 없었기 때문에, 필름 삽입 사출 시편의 휨을 최소화하기 위해서 유리 섬유가 강화된 복합재료를 기판으로 사용하였다. 유리 단섬유의 분포를 마이크로 CT 장비를 이용하여 평가하였다. 복합재료로 구성된 기판을 이용한 필름 삽입 사출 시편의 배향 텐서와 휨을 계산하기 위해서는 적절한 마이크로 역학, 이방적 열팽창계수 및 닫힌 어림법 모델이 선택되어야만 한다. 여섯 종류의 마이크로 역학모델, 세 종류의 열 팽창 계수 모델 및 다섯 종류의 닫힌 어림법 모델을 고려한 후, Mori-Tanaka 모델, Rosen and Hashin 모델 및 third orthotropic 닫힌 어림법 모델을 선택하였다. 수치적으로 계산된 섬유 배향 텐서와 휨에 관한 결과들은 실험결과와 잘 일치하였고, 유리 섬유의 보강효과가 필름 삽입 사출 복합 재료 시편의 휨에 미치는 영향을 파악하였다.

• Steel and Composite Structures
• /
• 제28권2호
• /
• pp.223-231
• /
• 2018

Nowadays, there are a great number of various structures that have been retrofitted by using different FRP Composites. Due to this, more researches need to be conducted to know more the characteristics of these structures, not only that but also a comparison among them before and after the retrofitting is needed. In this research, a model steel structure is tested using a bench-scale earthquake simulator on the shake table, using recorded micro tremor data, in order to get the dynamic behaviors. Columns of the model steel structure are then retrofitted by using GFRP composite, and then tested on the Quanser shake table by using the recorded micro tremor data. At this stage, it is needed to evaluate the dynamic behaviors of the retrofitted model steel structure. Various types of methods of OMA, such as EFDD, SSI, etc. are used to take action in the ambient responses. Having a purpose to learn more about the effects of GFRP composite, experimental model analysis of both types (retrofitted and no-retrofitted models) is conducted to evaluate their dynamic behaviors. There is a provision of ambient excitation to the shake table by using recorded micro tremor ambient vibration data on ground level. Furthermore, the Enhanced Frequency Domain Decomposition is used through output-only modal identification. At the end of this study, moderate correlation is obtained between mode shapes, periods and damping ratios. The aim of this research is to show and determine the effects of GFRP Composite implementation on structural responses of the model steel structure, in terms of changing its dynamical behaviors. The frequencies for model steel structure and the retrofitted model steel structure are shown to be 33.916% in average difference. Finally, it is shown that, in order to evaluate the period and rigidity of retrofitted structures, OMA might be used.

• 대한기계학회논문집A
• /
• 제21권11호
• /
• pp.1896-1911
• /
• 1997

Effects of fiber-matrix interphases on the micro-and macro-mechanical behaviors of unidirectionally fiber-reinforced composites subjected to transverse shear loading at remote distance have been studied. The interphases between fibers and matrix have been modeled by the spring-layer which accounts for continuity of tractions, but allows radial and circumferential displacement jumps across the interphase that are linearly related to the normal and tangential tractions. Numerical calculations for basic cells of the composites have been carried out using the boundary element method. For an undamaged composite the micro-level stresses at the matrix side of the interphase and effective shear stiffness have been computed as functions of fiber volume ratio $V_f$ and interphase stiffness k. Results are presented for various interphase stiffnesses from the perfect bonding to the case of total debonding. For a square array composite the results show that for a high interphase stiffness k>10, an increase of $V_f$ increases the effective transverse shear modulus G over bar of the composite. For a relatively low interphase stiffness k<1, it is shwon that an increase of $V_f$ slightly decreases the effective transverse shear modulus. For the perfect bonding case, G over bar for a hexagonal array composite is slightly larger than that for a square array composite. Also for a damaged composite partially debonded at the interphase, local stress fields and effective shear modulus are calculated and a decrease in G over bar has been observed.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 춘계학술발표대회 논문집
• /
• pp.211-214
• /
• 2003

This paper presents the microscopic observation results from the picture frame test using five-harness satin weave fabric composite. Aligned and misaligned specimens are observed to verify the exact tow deformation pattern such as tow interval and change in tow amplitude. To observe the micro-deformation of the fabric structure, appropriate specimens from picture frame test are sectioned and observed under the microscope. From the observation results, it is found that a picture frame test with a misaligned fibre orientation angle shows large differences in deformation between tensile and compressive tow directions.

• 대한임베디드공학회논문지
• /
• 제2권2호
• /
• pp.76-81
• /
• 2007

A novel multi-layer type micro gas sensor for $NO_X$ detection was designed and fabricated. Micro platform defined as type II-1 in this article for micro gas sensor was fabricated using the MEMS technology to meet the demanding needs of lower power consumption. Nano composite materials were fabricated with nanosized tin oxide powder and $\underline{m}$ulti-$\underline{w}$all $\underline{c}$arbon $\underline{n}$ano $\underline{t}$ube (MWCNT) to improve sensitivity. We investigated characteristics of fabricated multi-layer type micro gas sensor with $NO_2$ concentration variations at constant 2.2 V. Sensitivity (S) of micro gas sensor were observed to increase from 2.9, to 7.4 and 11.2 as concentrations of $NO_2$ gases increased from 2.4 ppm, to 3.6 ppm and 4.9 ppm. When 2.4 ppm of $NO_2$ gas was applied, response time and recovery time of micro gas sensor were recorded as 101 seconds and 142 seconds, respectively.

• Journal of Mechanical Science and Technology
• /
• 제16권5호
• /
• pp.666-675
• /
• 2002

Piezoelectric Fiber Composites with Interdigitated Electrodes (PFCIDE) were previously introduced as an alternative to monolithic wafers with conventional electrodes for applications of structural actuation. This paper is an investigation into the performance improvement of piezoelectric fiber composite actuators by changing the matrix material. This paper presents a modified micro-electromechanical model and numerical analyses of piezoelectric fiber/piezopolymer matrix composite actuator with interdigitated electrodes (PFPMIDE). Various concepts from different backgrounds including three-dimensional linear elastic and dielectric theories have been incorporated into the present linear piezoelectric model. The rule of mixture and the modified method to calculate effective properties of fiber composites were extended to apply to the PFPMIDE model. The new model was validated when compared with available experimental data and other analytical results. To see the structural responses of a composite plate integrated with the PFPMIDE, three-dimensional finite element formulations were derived. Numerical analyses show that the shape of the graphite/epoxy composite plate with the PFPMIDE may be controlled by judicious choice of voltages, piezoelectric fiber angles, and elastic tailoring of the composite plate.

• Transactions on Electrical and Electronic Materials
• /
• 제18권4호
• /
• pp.203-206
• /
• 2017

The effect of the content of microsilica and nanosilica continuously modified with hydroxy silane and epoxy-modified silicone in cycloaliphatic epoxy/microsilica/nanosilica composites (EMNCs) on the mechanical and water repellent properties was evaluated. Surface-modified micro- and nanosilica was well-mixed with a cycloaliphatic epoxy resin in the presence of polyester-modified polydimethylsiloxane (PEM-PDMS) as a dispersing agent using an ultrasonicator. Tensile and flexural tests were carried out using a universal testing machine (UTM). The water repellent property was evaluated by contact angle measurements of water on the composite surface. Tensile strength of the composite could be enhanced by 32.2% up to 91.4 MPa, and the flexural strength was raised to 122.0 MPa, which is 38.8% higher than that of neat epoxy. The contact angle of water on the composite was as high as $104.1^{\circ}$.