• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.8
• /
• pp.543-548
• /
• 2003

In this paper, we have proposed and fabricated a two-axis rotational micro-mirror with large tilt angle. Such a micro-mirror is a key element for N$\times$N high capacity optical cross-connect switches. The micro-mirror is required to have large tilt angle to increase the capacity of the cross-connect switches. For larger micro-mirror tilt angle between the grounded mirror plate and the bottom electrode is to be large enough to provide space for the tilting of the mirror. For our proposed structure, the gap was produced in such a way that the grounded mirror plate and the bottom electrode were made separately in different substrates by using the bulk micromachining technology, and combined later by employing self-align technique. As a result, a large tilt angle has been achieved without using additional actuators. The measured tilt angles were as large as $\pm$5.5$^{\circ}$ and $\pm$8.4$^{\circ}$ in the x and y direction respectively, and the pull-in voltages for the two directions were 380 V and 275 V respectively. Finally the fabricated mirror was successfully utilized to steer the optical beam. To our knowledge, our micro-mirror has the best performance among the micro-mirrors reported internationally so far.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.2
• /
• pp.263-266
• /
• 2007

We report a nickel optical MEMS switch, being able to rotate through a large angle and to accommodate multiple channels. The proposed optical switch consists of a thin nickel mirror and two torsion springs supporting the mirror. The torsion springs are designed using a finite element method (FEM) such that plastic deformation of the thin nickel is avoided during the large torsion actuation. For switching speed improvement, transient vibration of the released mirror is suppressed by optimizing the mirror design and a fast switching response of $200\;{\mu}s\;(pull-down)/300\;{\mu}s\;(pull-up)$ is demonstrated.

• Transactions on Control, Automation and Systems Engineering
• /
• v.3 no.4
• /
• pp.236-241
• /
• 2001

Teach pendant is the most widely used means of robot teaching at present. Despite the difficulties of using the motion command buttons on the teach pendant, it is an economical, robust, and effective device for robot teaching task. This paper presents the development of a force/moment direction sensor named COSMO that can improve the teach pendant based robot teaching. Robot teaching experiment of a six axis commercial robot using the sensor is described where operator holds the sensor with a hand, and move the robot by pushing, pulling, and twisting the sensor in the direction of the desired motion. No prior knowledge of the coordinate system is required. The function of the COSMO sensor is to detect the presence f force and moment along the principal axes of the sensor coordinate system. The transducer used in the sensor is micro-switch, and this intuitive robot teaching can be implemented at a very low cost.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.2
• /
• pp.22-32
• /
• 2002

MEMS(Micro-Electro-Mechanical Systems)는 전기적인 구성요소와 기계적인 구성요소를 작게 조합하여 구성한 소자나 시스템을 말한다. RF(Radio Frequency) MEMS는 MEMS를 이용한 RF 소자나 시스템을 의미하며, 본 고에서는 RF 소자에 대하여 논의하고자 한다. MEMS는 RF 소자의 성능, 기능, 집적화 등을 높여 주고, 크기, 가격, 부피, 전력 소모 등을 낮추어 주므로 소자 개발에 대한 연구는 매우 다양하지만, 본 고에서는 움직이는 소자 중에서 가장 많이 연구되고 있는 mechanical RF switch에 대하여 중점적으로 다루고자 한다. 이에 대한 연구 동향, 특성, 응용 분야 등을 살펴보고, 상품으로서의 가치를 인정 받기 위하여 고려해야 할 점들을 논의 하겠다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.126-129
• /
• 2010

MEMS(micro electro-mechanical systems) inertial switch which is applicable to the ignition Safe-Arm- Unit of propulsion system is devised. The MEMS inertial switch is designed according to the general design procedure for conventional mechanical elements. Unlikely conventional MEMS accelerometer, threshold inertial switching mechanism is adopted which makes a MEMS element an abrupt switching in a certain acceleration level. By comparing the design data and test results of the specimen a small discrepancy in switching acceleration level is found which is presumably due to the nonlinear characteristics of the beam spring and the flexure hinge which are the main parts of the MEMS inertial switch.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.12
• /
• pp.796-802
• /
• 2016

In order to develop an electrical insulation material for gas GIS (insulation switch gear) spacer, 4 types of epoxy/micro-alumina (40, 50, 60, 70 wt%) composites and 9 types of epoxy/nano-alumina (1, 3, 5 g)/micro-alumina (40, 50, 60, 70 wt%) composites were prepared and tensile test was carried out. In here, nano-alumina was previously surface-treated with GDE (glycerol diglycidyl ether). As micro-alumina and GDE-treated nano-alumina contents increased, tensile strength increased and the highest value was shown in the system with 3 g GDE-treated nano-alumina.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.1053-1057
• /
• 1997

Laser thin film process with a Q-switch pulsed YAG laser was performed for micro machining. In this research, we performed basic Cr thin film on glass substrates removal machining experiments. Form experiments, it happens not only evaporration of thin film but also spatter and cohesion of melting substance in working region, when machining a Cr thin film by Q-switch YAG laser beam irradiation. Critical energy of surface irradiation type by irradiation direction of laser in a face composing thin film on the glass is higher than that of back irradiation type, but the latter is favorable because of spatter appearance. In case of image formation position when laser beam is irradiated, the defocus is permitted to a certain extent within forcus depth. Ifexceeds focus depth, formation of pattern is vanishing step by step.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.8 s.185
• /
• pp.163-170
• /
• 2006

By removing sacrificial layer through ashing process, movable MEMS structure on substrate can be fabricated in surface micromachining. However, MEMS structure includes, during the ashing process, the warping or buckling effects due to stress gradient along the vertical direction of thin film. In this study, we presented method for counteracting the unwanted deflection of MEMS structure and designed using character of deposit process to overcome limited design conditions. Unit cell patterns were designed with character of deposit shape, and their final shapes were adopted using Finite Element Method. Finally, RF MEMS switch was fabricated by surface micro machining as test vehicles. We checked out that alleviation effect for deformation of switch improved by 35%.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.697-700
• /
• 2002

In this paper, we proposed the micro web-server Implementation on Strong ARM processor with embedded Linux. The parallel port connecting parallel I/O is controlled via HPPT protocol and web browser program. HTTP protocol is ported into Linux and the micro web server program and port control program are installed on-board memory using CGI to be accessed by web browser, such as Internet Explore and Netscape. 8bit LED and DIP switches are connected to the processor port and the switch input status is monitored and the LED output is controlled from remote hosts vie internet. The result of the proposed embedded micro-web server can be used in automation systems, remote distributed control via internet using web browser.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.3
• /
• pp.129-133
• /
• 2016

Theoretical and graphical analysis of pull-in-voltage and figure of merit for a fixed-fixed capacitive Micro Electromechanical Systems (MEMS) switch is presented in this paper. MEMS switch consists of a thin electrode called bridge suspended over a central line and both ends of the bridge are fixed at the ground planes of a coplanar waveguide (CPW) structure. A thin layer of dielectric material is deposited between the bridge and centre conductor to avoid stiction and provide low impedance path between the electrodes. When an actuation voltage is applied between the electrodes, the metal bridge acquires pull in effect as it crosses one third of distance between them. In this study, we describe behavior of pull-in voltage and figure of merit (or capacitance ratio) of capacitive MEMS switch for five different dielectric materials. The effects of dielectric thicknesses are also considered to calculate the values of pull-in-voltage and capacitance ratio. This work shows that a reduced pull-in-voltage with increase in capacitance ratio can be achieved by using dielectric material of high dielectric constant above the central line of CPW.