• Journal of the Korean Ceramic Society
• /
• v.43 no.12 s.295
• /
• pp.852-858
• /
• 2006

It is well known that $BaMgAl_{10}O_{17}:Eu^{2+}$ (BAM) and $CaMgSi_2O_6:Eu^{2+}$ (CMS) are a highly efficient blue phosphor. However, these phosphors in the form of thin films have not yet been realized clue to technical difficulties. We prepared thin film type BAM and CMS phosphors on quartz glass substrate using a pulsed laser deposition technique. The luminescent and structural properties of thin film phosphors were monitored as a function of key processing parameters such as oxygen partial pressure inside the deposition chamber, deposition time, laser energy density and the type of post-deposition treatments used. Even though we could not obtain single homogenous phases, thin films with large homogenous areas and a high photoluminescence could be produced by optimizing these processing parameters.

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.85-90
• /
• 2007

Lanthanum aluminate($LaAlO_3$) film has been prepared on single crystal and metal substrates by dip coating method. Lanthanum acetate and aluminum were prepared via ligand exchange starting from lanthanum nitrate hexahydrate and aluminum nitrate hexahydrate in acetate glacial acetic acid solution after being refluxed. Coating solution was obtained by diluting the gel with methanol and 2-methoxyethanol to adjust the total cation concentration to 0.67 M. Precursor coated film was prepared by dip-coating with a speed of 25 mm/min on various substrates such as $LaAlO_3$ (001), MgO(001), $SrTiO_3$(001) single crystal, LMO/MgO/Ni-alloy. Thin films have been obtained by heat treating the precursor film at various temperatures from $600^{\circ}C{\sim}900^{\circ}C$ and various heating rate from $0.83^{\circ}C/min{\sim}1.25^{\circ}C/min$ under $Ar/O_2$ mixture containing 1000ppm oxygen. The films have been characterized by scanning electronic microscopy (SEM) and X-ray diffraction (XRD). XRD analysis for the prepared film showed that $LaAlO_3$ thin films with a preferred orientation of (100) plane parallel to substrate surface were obtained at $800^{\circ}C(1.11\;^{\circ}C/min)$ on LMO/MgO/Ni-alloy substrate, but the intensity decreased with the increase of heat treatment temperature.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.317-317
• /
• 2011

Water dissociation on oxide surface has been researched in many fields because of its importance as fundamental phenomenas. MgO(001) is a good model system to understand heterogeneous catalysis, gas sensors, ground-water contaminants, and atmosphere chemistry. Over decades, ultrathin film of MgO on Ag(100) have attracted research activities thanks to its enhanced catalytic property. Correlation of the oxide and the metal, potential screening, charge fluctuation from interface reconstruction makes different energetics of hydroxylation of waters on film. We calculate the water-spliting energetics under the vacuum system.

• Journal of the Korean Ceramic Society
• /
• v.33 no.7
• /
• pp.802-808
• /
• 1996

PbTiO3 thin films were fabricated onto MgO(100) single crystal substrate by reactive D. C magnetron sput-tering of Pb and Ti metal in an oxygen and argon gas mixture. The annealing of the thin films resulted in the decrease of both the c-axis orientation ratio and the lattice parameter. It is well known that the c-axis lattice parameter of thin film is dependent on the Pb/(Pb+Ti)ratio and the residual stress in the film The PbTiO3 thin films with a Pb/(Pb+T) ratio ranging from 0.45 to 0.57 were fabricated and annealed. The structure of the film the c-axis orientation ratio and the lattice parameter were not dependent on the Pb/(Pb+Ti) ratio before and after annealing. These experimental results proved that the decrease of the c-axis lattice parameter under the annealing conditions was due to the relaxation of the intrinsic stress in the film. This relaxation of the intrinsic stress caused the decrease of the c-axis orientation ratio and this phenomenon can be explained by c-axis growth lattice model.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.4
• /
• pp.256-261
• /
• 2021

Indium-doped Mg_0.05Zn_0.95O thin films were deposited on glass substrates by a sol-gel method. Three types of indium precursors such as indium chloride, indium acetate, and indium nitrate were used as doping sources. Physical properties of fabricated thin films were analyzed through XRD (x-ray diffraction), UV-vis spectrophotometer, Hall effect measurement, and EDS (energy dispersive x-ray spectroscopy). All In-doped thin films grown in this study exhibited a preferred orientation of (002) with over 80% transmittance. The results showed that the Mg_0.05Zn_0.95O thin film from indium chloride as the indium precursor has higher crystallinity and transmittance with lower resistivity when compared with those from other indium precursors.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.2
• /
• pp.68-72
• /
• 2009

We report on the growth of $CuCrO_2$ films using pulsed laser deposition and their structural and electrical transport properties. $CuCrO_2$ thin films were doped with 5 at% Mg for p-type properties. Epitaxial films of $CuCr_{0.95}Mg_{0.05}O_2$ were grown on c-plane sapphire substrates. The effects of growth temperature and oxygen pressure on film properties were investigated. The main phase of delafossite $CuCr_{0.95}Mg_{0.05}O_2$ was appeared above the growth temperature of $600^{\circ}C$. The thin film grown at $500^{\circ}C$ showed the highest conductivity, reaching 19.6 S/cm while higher growth temperatures over $500^{\circ}C$ led to lower conductivity; the thin film grown at $700^{\circ}C$ showed 0.02 S/cm.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.1
• /
• pp.81-86
• /
• 2016

$Eu^{3+}$-doped $MgMoO_4$ phosphor thin films were deposited on quartz substrates by radio frequency magnetron sputtering with changing various growth temperatures. The effects of growth temperature on the structure, transmittance, optical band gap, and luminescence of the phosphor thin films were characterized. All the phosphor thin films, irrespective of growth temperature, showed a monoclinic structure with a main (220) diffraction peak. The thin film deposited at a growth temperature of $400^{\circ}C$ indicated an average transmittance of 90% in the wavelength range of 500 ~ 1100 nm and band gap energy of 4.81 eV. The excitation spectra of the phosphor thin films consisted of a broad charge transfer band peaked at 284 nm in the range of 230 ~ 330 nm and two weak peaks located at 368 and 461 nm, respectively. The emission spectra under ultraviolet excitation at 284 nm exhibited a sharp emission peak at 614 nm and several weak bands. All the phosphor thin films showed high asymmetry ratio values, indicating that $Eu^{3+}$ ions incorporated into the host lattice occupied at the non-inversion symmetry sites. The results suggest that the growth temperature plays an important role in growing high-quality phosphor thin films.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2002.05a
• /
• pp.41-41
• /
• 2002

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.507-510
• /
• 2004

Oblique ion-induced secondary electron emission coefficient(${\gamma}$) with low energy ..and work function ${\phi}_{\omega}$(${\theta}$ = 0 and ${\theta}$ = 20) of the MgO thin film in AC-PDPs has been measured by ${\gamma}$-FIB system. The MgO thin film has been deposited from sintered material under electron beam evaporation method. The energy of $He^+$ ions used has been ranged from 50eV to 150eV. Oblique ion beam has been chosen to be 10 degree, 20 degree and 30 degree. It is found that the higher secondary electron emission coefficient(${\gamma}$) has been achieved by the higher oblique ion beam up to inclination angle of 30 degree than the perpendicular incident ion beam.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.587-588
• /
• 2005

Ozone is useful oxidizing gas for the fabrication of BSCCO thin films. In order to obtain high quality oxide BSCCO thin films, higher ozone concentration is necessary. The growth rates of the films was set in the region from 0.17 to 0.27 nm/min. MgO(100) was used as a substrate. In this paper oxidation property was evaluated relation between oxide gas pressure and inverse temperature(CuO reaction). The obtained condition was formulated by the fabrication of Cu metal thin film by co-deposition using the Ion Beam Sputtering method. Because the CuO phase peak appeared at the XRD evaluation of the CuO thin film using ozone gas, this study has succeeded in the fabrication of the CuO phase at $825^{\circ}C$.