• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.1
• /
• pp.108-114
• /
• 1998

This paper presents the design and fabrication of waveguide E-plane metal insert bandpass filter for milli-meter waves which is analyzed transmission characteristics by calculating the generalized scattering matrix using mode-matching method. The bandpass filter was fabricated to verify the proposed method by the WR-34 rectangular waveguide to operate in 30.085 ~ 30.885 GHz. The fabricated waveguide E-plane metal insert band- pass filter was established the fact that it is so adaptive for milli-meter waves due to the measured data closely consistent with the results of analysis using mode-matching method, that is, the maximum value of insertion loss is 0.8 dB and the return loss is below -15 dB.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.4
• /
• pp.1644-1654
• /
• 2018

Eigenvalue distributions for a periodic metal-insulator-metal waveguide, classified into the point spectrum and the discretized continuous spectrum (DCS), are investigated as functions of frequencies, gap widths, and periods. Muller's method is suggested for solving exact eigenvalues, and we propose the scheme for finding proper initial values in the Muller's method by considering only ${\Re}e({\varepsilon}_r)$ in the dispersion equation. We then find that anti-crossing behavior, repulsive effect between the point spectrum and the DCS, becomes stronger when the real parts of the roots in the point spectrum have smaller values. Finally, we examine the transmittances of a single subwavelength slit for real metals using the mode matching technique. The transmittances in real metals similarly follow those of the perfect electric conductor (PEC) at low frequencies, while the patterns at higher frequencies begin to differ from the PEC.

• Korean Journal of Optics and Photonics
• /
• v.19 no.1
• /
• pp.73-79
• /
• 2008

We propose a novel metal-waveguide structure for sustaining long-range surface-plasmon-polaritons (LRSPP). The LRSPP waveguides are composed basically of two asymmetric metal layers: a very thin, finite-width metal strip on top of a metal slab with a dielectric gap in between them. Mode cut-off of LRSPPs excited on the double-metal waveguides is characterized by consistently investigating their dispersion relations and mode profiles. We also confirm experimentally the existence of low-loss, well-confined LRSPP modes by measuring far-field outputs emerging from an edge of the asymmetric double-metal waveguides. In the experiment, we have fabricated several types of SPP waveguide devices including straight lines, S-bend, and Y-branch consisting of gold strips (20 nm-thick, $5{\mu}m$-wide). Overall propagation loss of the proposed double-metal waveguides is quite comparable to that of single metal-strip waveguides, in addition the mode sizes can be tuned by increasing the core-insulator gap between the metal layers to get a higher coupling efficiency with a single-mode fiber in telecom wavelength. The proposed LRSPP waveguides may open up realization of SPP-waveguide sensors or nonlinear SPP-devices by replacing the core-insulator with a bio-fluid or a nonlinear medium.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.4
• /
• pp.53-59
• /
• 2000

Based on the polarization selectivity of fiber-to-planar waveguide coupler, a novel fiber optic polarizer has been designed and fabricated. The large structural birefringence of a metal-clad planar waveguide enables the polarizer to have wide operating wavelength range. The polymer and gold were used for the guiding layer and cladding layer of the planar waveguide, respectively. The experimental results showed that either TE or TM polarized lightwave could be created by adjusting the thickness of planar waveguide. Operating wavelegth range satisfying more than 16㏈ polarization extinction ratio was 130nm. The average insertion loss of fabricated devices was order of 0.5㏈.

• Proceedings of the Optical Society of Korea Conference
• /
• 1990.02a
• /
• pp.257-259
• /
• 1990

In the design of waveguide E-plane bandpass filter, it is very important to characterize the K-inverters. In the analytical method. losses arising from the metal and the dielectric are ignored for the simplicity of design process. In this paper, based on the new measurement method, characteristics of inverters are measured and compared with those calculated based on mode-matching analysis.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.406-412
• /
• 2018

In this paper, we propose a narrow resonant waveguide probe that can improve the measurement sensitivity in near-field scanning microwave microscopy. The probe consists of a metal waveguide incorporating the following two sections: a straight section at the tip of the probe whose cross-section is a double-ridged rectangle, and whose height is much smaller than the waveguide width; and a standard waveguide section. The advantage of the narrow waveguide is the same as that of the quarter-wave transformer section i.e., it achieves impedance-matching between the sample under test (SUT) and the standard waveguide. The design procedure used for the probe is presented in detail and the performance of the designed resonant probe is evaluated theoretically by using an equivalent circuit. The calculated results are compared with those obtained using the finite element method (Ansoft HFSS), and consistency between the results is demonstrated. Furthermore, the performance of the fabricated resonant probe is evaluated experimentally. At X-band frequencies, we have measured the one-dimensional scanning reflection coefficient of the SUT using the probe. The sensitivity of the proposed resonant probe is improved by more than two times as compared to a conventional waveguide cavity type probe.

• Journal of the Optical Society of Korea
• /
• v.20 no.1
• /
• pp.180-187
• /
• 2016

The independent operation of a color filter for incident polarization is demonstrated using a guided-mode resonance (GMR) filter employing a metal-insulator-metal (MIM) waveguide. To achieve independent operation, a rectangular MIM grating is proposed as a wave-guide resonator. The design considerations are discussed and include how to determine the grating period and slit width. Power flow distribution is observed with slit width variation. Blue-green, green-red, and blue-red filters for corresponding x- and y-polarizations are demonstrated as application examples with numerical simulation with rectangle-shaped MIM grating. As a practical application, feasibility as a chromatic polarizer is discussed.

• Journal of the Optical Society of Korea
• /
• v.15 no.2
• /
• pp.118-123
• /
• 2011

A novel triangular-shaped plasmonic metal-insulator-metal (MIM) Bragg grating waveguide is introduced, whose band-gap is narrower than that of the conventional step type and wider than that of the sawtoothshaped one. Moreover apodized triangular-shaped MIM Bragg grating structures are proposed in order to reduce the side lobes of the transmission spectrum, because the Bragg reflector with a sawtooth profile has a smoother transmission spectrum than that of a triangular-shaped one. The performance of the proposed structures is simulated by using the finite difference time domain method.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.1
• /
• pp.18-24
• /
• 2006

Reactor core and internal structures of a liquid metal reactor (LMR) can not be visually examined due to an opaque liquid sodium. The under-sodium viewing technique by using an ultrasonic wave should be applied far the visual inspection of reactor internals. In this study, an ultrasonic waveguide sensor with a strip plate has been developed for an application to the under-sodium viewing technique. The Lamb wave propagation of a waveguide sensor has been analyzed and the zero-order antisymmetric $A_0$ plate wave was selected as the application mode of the sensor. The $A_0$ plate wave can be propagated in the dispersive low frequency range by using a liquid wedge clamped to the waveguide. A new technique is presented which is capable of steering the radiation beam angle of a waveguide sensor without a mechanical movement of the sensor assembly The steering function of the ultrasonic radiation beam can be achieved by a frequency tuning method of the excitation pulse in the dispersive range of the $A_0$ mode. The technique provides an opportunity to overcome the scanning limitation of a waveguide sensor. The beam steering function has been evaluated by an experimental verification. The ultrasonic C-scanning experiments are performed in water and the feasibility of the ultrasonic waveguide sensor has been verified.

• ETRI Journal
• /
• v.31 no.6
• /
• pp.778-783
• /
• 2009

To fabricate uniform and reliable thin gold stripes that provide low-loss optical waveguides, we developed a novel liftoff process placing an additional $SiN_x$ layer under conventional photoresists. By patterning a photoresist and over-etching the $SiN_x$, the photoresist patterns become free-standing structures on a lower-cladding. This leads to uniform metal stripes with good reproducibility and effectively removes parasitic structures on the edge of the metal stripe in the image reversal photolithography process. By applying the newly developed process to polymer-based gold stripe waveguide fabrication, we improved the propagation losses about two times compared with that incurred by the conventional image-reversal process.