• Resources Recycling
• /
• v.3 no.1
• /
• pp.17-24
• /
• 1994

Recovery of precious metal values from petrochemical spent catalyst is important from the viewpoint of environmental protection and resource recycling. Two types of spent catalysts were used in this study. One used in the manufacture of ethylene contains 0.3% Pd in the alumina substrate. The other used in oil refining contains 0.3% Pt and 0.3% Re. Both spent catalysts are roasted to remove volatile matters as carbon and sulfur. Then, metallic Pd powder from Pd spent catalyst is obtained in the course of grinding, hydrochloric acid or aqua regia leaching and cementation with iron. For the recovery of Pt and Re from Pt-Re spent catalyst, Pt and Re are leached with either HCI or aqua regia, first. Metallic Pt powder is recovered from the leach solution by cementation with Fe powder. Re in sulfide form is precipitated by the addition of sodium sulfide to the solution obtained after Pt recovery. It is found that 6N HCI can be successfully used as leaching agent for both types of spent catalyst. 6N HCI is considered to be better than aqua regia in consideration of reagent and equipment cost.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.151-151
• /
• 2007

최근에 에피 성장된 ZnO는 UV-LED, 화학적-바이오센서와 투명전도 전극에 많은 관심을 받고 있다. 고 품질의 ZnO는 Metal-organic chemical vapor deposition(MOCVD), Pulsed laser deposition(PLD), molecular beam epitaxy(MBE), 그리고 마그네트론 스퍼터링법에 의해 성장이 이루어지고 있다. 대부분의 ZnO는 사파이어, 싫리콘과 같은 이종 기판 위에 성장되고 있으며, Heteroepitaxy로 성장된 ZnO 박막은 기판과 박막사이의 격자상수, 열팽창계수 차이로 인해 높은 결함 밀도를 보이고 있다. 이러한 문제점은 광전자 소자 응용에 있어 여러 가지 문제점을 야기 시킨다. 이와 같은 문제점을 해결하기 위해 박막과 기판사이에 저온 버퍼층을 사용하거나 같은 물질의 버퍼층을 사용하여 결할 밀도를 감소시키고, 높은 결정성을 가진 ZnO 박막을 성장시킨 결과들이 많이 보고되어지고 있다. 본 연구에서는 마그네트론 스퍼터링 법으로 저온 버퍼층 성장 없이 성장온도 만을 달리 하여 고품질의 ZnO 박막을 성장시켰다. ZnO 박막은 c-sapphire 기판위에 ZnO(99.9999%)의 타겟을 사용하여 $600{\sim}800^{\circ}C$ 온도에서 성장시켰고, 스퍼터링 가스로는 아르곤과 산소를 2:1 비율로 혼합하여 15mtorr의 압력에서 성장하였다. 이렇게 성장시킨 ZnO 박막은 Transmission Electron Microscopy (TEM), High-Resolution X-ray Diffraction (HRXRD), Low-temperature PL, 그리고 Atomic Force Microscopy (AFM)로 특성을 분석 하였다. ZnO 박막은 HRXRD (002) 면의 $\omega$-rocking curve운석 결과, $0.083^{\circ}$의 작은 FEHM을 얻었고, (102) 면의 $\varphi$-sacn을 통해 온도가 증가함에 따라 향상된 6-fold을 확인함으로새 에피성장됨을 알 수 있었다. 또한 TEM분석을 통해 $800^{\circ}C$에서 성장된 박막은 $6.7{\times}10^9/cm^2$의 전위밀도를 얻을 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.192-193
• /
• 2007

An evaporated Ti/Pd/Ag contact system is most widely used to make high-efficiency silicon solar cells, however, the system is not cost effective due to expensive materials and vacuum techniques. Commercial solar cells with screen-printed contacts formed by using Ag paste suffer from a low fill factor and a high shading loss because of high contact resistance and low aspect ratio. Low-cost Ni and Cu metal contacts have been formed by using electro less plating and electroplating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Ni/Cu alloy is plated on a silicon substrate by electro-deposition of the alloy from an acetate electrolyte solution, and nickel-silicide formation at the interface between the silicon and the nickel enhances stability and reduces the contact resistance. It was, therefore, found that nickel-silicide was suitable for high-efficiency solar cell applications. Cu was electroplated on the Ni layer by using a light induced plating method. The Cu electroplating solution was made up of a commercially available acid sulfate bath and additives to reduce the stress of the copper layer. In this paper, we investigated low-cost Ni/Cu contact formation by electro less and electroplating for crystalline silicon solar cells.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.268-268
• /
• 2006

YBCO 초전도 박막을 제조하기 위해 일반적으로 사용되는 RABiTS공정을 통해 제조된 양축 정렬된 Ni 선재 위에 직접 YBCO를 증착시키려는 시도가 많이 이루어졌다. Ni 위에 직접 증착시킨 YBCO 박막은 c-축으로 정렬되는 온도에서 Ni이 확산되어 YBCO와 반응하여 초전도 물성을 약화시킨다. 이것을 방지하기 위하여 완층층을 먼저 증착을 하는 연구를 시행하였다. 본 연구는 Ni-5at.%W(100) 기판위에 hot-wall type MOCVD (metal organic chemical vapor deposition)를 이용하여 증착을 실시하였다. 완층층으로는 Ni, YBCO와 각각 4.70%, 3.32%의 lattice mismatch를 갖는 $Yb_2O_3$를 선택하였으며, 증착 조건으로는 온도 $800\;{\sim}\;1000^{\circ}C$, 시간 3 ~ 10min, 증착압력 10 Torr의 조건에서 증착을 행하였다. $Yb_2O_3$를 형성하기 위해 산소를 이용하였으나 $Yb_2O_3$(200) 형성을 방해하는 NiO(111)이 형성되었다. 산소를 대신해 수증기를 이용하여 NiO 상이 없는 $Yb_2O_3$(200)을 형성하였다. 증착 시간과 수증기 압력에 따른 $Yb_2O_3$의 $I_{(200)}/(I_{(111)}+I_{(200)})$의 상대 회절강도비를 XRD (X-ray diffraction)를 이용하였고, 증착된 표면 형상은 SEM(scanning electron microscopy)을 통해 관찰하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.820-824
• /
• 2014

TiNOx multi-layer thin films on aluminum substrates were prepared by DC reactive magnetron sputtering method. 4 multi-layers of $TiO_2$/TiNOx(LMVF)/TiNOx(HMVF)/Ti/substrate have been prepared with ratio of Ar and ($N_2+O_2$) gas mixture. $TiO_2$ of top layer is anti-reflection layer on double TiNOx(LMVF)/TiNOx(HMVF) layers and Ti metal of infrared reflection layer. In this study, the crystallinity and surface properties of TiNOx thin films were estimated by X-ray diffraction(XRD) and field emission scanning electron microscopy(FE-SEM), respectively. The grain size of TiNOx thin films shows to increase with increasing sputtering power. The composition of thin films has been investigated using electron probe microanalysis(EPMA). The optical properties with wavelength spectrum were recorded by UV-Vis-NIR spectrophotometry at a range of 200~1,500 nm. The TiNOx multi-layer films show the excellent optical performance beyond 9% of reflectance in those ranges wavelength.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.96-101
• /
• 2005

Fluoropolymer of PTFE and PFA etc. is a heat resistance polymeric material that it is known as that maximum continuous use temperature reaches for 260 $^{\circ}C$. It was observed that these polymers had the enough thermal stability so enough that it was kept by thermal aging of 280 $^{\circ}C$/7 weeks too in this study. However, such thermal stability means that bulk material property is kept such as mechanical strength, melting point and initial pyrolysis temperature etc. If these polymers are evaluate by coating property such as surface contact angle, surface morphology, surface scratch, thing that heat resistance is not enough was confirmed in this study. Thermal aging of flouropolymer coating was achieved by gear aging oven that the exchange rate of air was controlled, and the analysis results were indicating serious damage of surface morphology and adhesive strength on metal substrate.

• Journal of the Korean Vacuum Society
• /
• v.14 no.4
• /
• pp.238-244
• /
• 2005

IZO thin films are prepared on a corning 7059 glass substrate in a mixed gases of Ar +$O_2$ by rf-magnetron sputtering, using a powder target with a composition ratio of $In_{2}O_{3}$ : ZnO=90 : 10 $wt.\%$. Their electrical sheet resistance are strongly dependent on the oxygen concentration introduced during the deposition, a minimum resistivity of $3.7\times10^{-4}\Omega\cdot$ cm and an average transmittance over $85\%$ in the visible range are obtained in a film deposited in pure Ar gas which is close to near the stoichiometry. During the heat treatment from room temperature up tp $600^{\circ}C$ in various environments, the electrical resistance changes are explained by cyrstallizations or oxidizations of In metal and InO contained in the IZO film. The electrical properties due to oxygen adsorption and phase transitions occurring at temperatures over $40000^{\circ}C$ during heat treatment in air are also investigated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.240.2-240.2
• /
• 2013

The device scale of flash memory was confronted with quantum mechanical limitation. The next generation memory device will be required a break-through for the device scaling problem. Especially, graphene is one of important materials to overcome scaling and operation problem for the memory device, because ofthe high carrier mobility, the mechanicalflexibility, the one atomic layer thick and versatile chemistry. We demonstrate the hybrid memory consisted with the metal-oxide quantum dots and the mono-layered graphene which was transferred to $SiO_2$ (5 nm)/Si substrate. The 5-nm thick secondary $SiO_2$ layer was deposited on the mono-layered graphene by using ultra-high vacuum sputtering system which base pressure is about $1{\times}10^{-10}$ Torr. The $In_2O_3$ quantum dots were distributed on the secondary $SiO_2$2 layer after chemical reaction between deposited In layer and polyamic acid layer through soft baking at $125^{\circ}C$ for 30 min and curing process at $400^{\circ}C$ for 1 hr by using the furnace in $N_2$ ambient. The memory devices with the $In_2O_3$ quantum dots on graphene monolayer between $SiO_2$ thin films have demonstrated and evaluated for the application of next generation nonvolatile memory device. We will discuss the electrical properties to understating memory effect related with quantum mechanical transport between the $In_2O_3$ quantum dots and the Fermi level of graphene layer.

• Korean Journal of Materials Research
• /
• v.16 no.10
• /
• pp.629-632
• /
• 2006

Electrical characteristics of Pt/Ti/Pt/Au and Pd/Zn/Pd/Au contacts to p-type InGaAs grown on an InP substrate have been characterized as a function of the doping concentration and the annealing temperature. The Pt/Ti/Pt/Au contacts produced the specific contact resistance as low as $2.3{\times}10^{-6}{\Omega}{\cdot}cm^2$, when heat-treated at an annealing temperature of $400^{\circ}C$. Comparison of the Pt/Ti/Pt/Au and Ti/Pt/Au contacts showed that the first Pt layer plays an important role in reducing the contact resistivity probably by lowering energy barrier at the metal-semiconductor interface. For the Pd/Zn/Pd/Au contacts, the contact resistivity remained virtually unchanged with increasing annealing temperature. The specific contact resistivity as low as $4.7{\times}10^{-6}{\Omega}{\cdot}cm^2$ was obtained. The results indicate that the Pt/Ti/Pt/Au and Pd/Zn/Pd/Au schemes could be potentially important for the fabrication of InP-based optoelectronic devices, such as photodetector and optical modulator.

• Korean Journal of Metals and Materials
• /
• v.56 no.11
• /
• pp.835-843
• /
• 2018

In this work, we report a delta rosette strain sensor based on highly stretchable silver nanowire (AgNW) percolation piezoresistors. The proposed rosette strain sensors were easily prepared by a facile two-step fabrication route. First, three identical AgNW piezoresistive electrodes were patterned in a simple and precise manner on a donor film using a solution-processed drop-coating of the AgNWs in conjunction with a tape-type shadow mask. The patterned AgNW electrodes were then entirely transferred to an elastomeric substrate while embedding them in the polymer matrix. The fabricated stretchable AgNW piezoresistors could be operated at up to 20% strain without electrical or mechanical failure, showing a maximum gauge factor as high as 5.3, low hysteresis, and high linearity ($r^2{\approx}0.996$). Moreover, the sensor responses were also found to be highly stable and reversible even under repeated strain loading/unloading for up to 1000 cycles at a maximum tensile strain of 20%, mainly due to the mechanical stability of the AgNW/elastomer composites. In addition, both the magnitude and direction of the principal strain could be precisely characterized by configuring three identical AgNW piezoresistors in a delta rosette form, representing the potential for employing the devices as a multidimensional strain sensor in various practical applications.