• 한국위성정보통신학회논문지
• /
• 제7권2호
• /
• pp.18-24
• /
• 2012

본 논문에서는 ESD 방지를 위한 최적 방법론에 목표하여 확장된 드레인을 갖는 EDNMOS 소자의 더블 스냅백 현상 및 백그라운 도핑 농도 (BDC)의 영향을 조사하였다. 고전류 영역에서 낮은 BDC를 가진 EDNMOS 소자는 강한 스냅백으로 인해 취약한 ESD 성능과 높은 래치업 위험을 가지게 되나, 높은 BDC를 가진 EDNMOS 소자는 스냅백을 효과적으로 방지할 수 있음을 알 수 있었다. 따라서 BDC 제어로 안정적인 ESD 방지 성능과 래치업 면역을 구현할 수 있음을 밝혔다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.5-6
• /
• 2005

High performance SiGe heterostructure metal-oxide-semiconductor field effect transistors(MOSFETs) were fabricated using well-controlled delta-doping of boron and SiGe/Si heterostructure epitaxal layers grown by reduced pressure chemical vapor deposition. In this paper, we report 1/f noise characteristics of the SiGe MOSFETs measured under various bias conditions of the gate and drain voltages changing in linear operation regions. From the noise spectral density, we found that the gate and drain voltage dependence of the noise represented same features, as usually scaled with $f^1$. However, 1/f noise was found to be much lower in the device with boron delta-doped layer, by a factor of $10^{-1}\sim10^{-2}$ in comparion with the device fabricated without delta-doped layer. 1/f noise property of delta-doped device looks important because the device may replace bipolar transistors most commonly embedded in high-frequency oscillator circuits.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.193-193
• /
• 2013

실리콘 박막 태양전지는 광 흡수층에서 형성된 정공과 전자를 효과적으로 분리하기 위해 p형과 n형으로 도핑된 층을 형성하는 p-i-n구조를 갖게 된다. 이러한 도핑 층을 형성하기 위해 B2H6와 PH3와 같은 독성 가스를 사용하기 때문에, 공정 안정성과 환경적인 이슈가 대두된다. 또한 도핑은 추가적으로 실리콘 박막 태양전지의 안정화 효율을 지속적으로 저하시키는 요인이 된다. 이러한 문제점을 개선하기 위하여, 창층으로 MoO3, V2O5, WO3 등과 같이 높은 일함수를 갖는 전이금속 산화물을 사용하고, 광 흡수층으로 i-Si:H을, 후면 전극으로 낮은 일함수를 나타내는 LiF/Al을 사용하였다. 전이금속 산화물과 LiF/Al의 큰 일함수 차이에 의해서 흡수층인 i-Si:H 에서 생성된 캐리어들은 효과적으로 분리되고 수집이 된다. 금속 산화물은 스퍼터링 공정에 의하여 이루어졌으며, 스퍼터링 공정조건에 따라 산화도가 조절되며, 이러한 산화도에 따라 태양전지의 셀 특성이 결정된다. 도핑 층이 없는 새로운 형태의 실리콘 박막 태양전지는 기존 비정질 실리콘 박막 태양전지에 비해 높은 안정화 효율을 나타내며, 이는 도핑 층이 없기 때문에 기존 실리콘 박막 태양전지의 열화현상에 따른 효율저하가 발생하지 않는 장점을 지내고 있다.

• 마이크로전자및패키징학회지
• /
• 제27권1호
• /
• pp.31-35
• /
• 2020

원자층 증착법(ALD: atomic layer deposition)으로 성장된 ZnO n-type 산화물반도체를 이용하여 three terminal memristor (memtransistor) 소자를 제작하여 습도에 따른 그 특성을 관찰하였다. 40 nm 두께의 ZnO 박막을 이용하여 channel width 70 ㎛, length 5 ㎛, back gate 구조의 memtransistor 소자를 제작하여 습도에 (40%, 50%, 60%, 70%) 따른 gate tunable memristive 특성변화를 관찰하였다. 습도가 높아질수록 electron mobility와 gate controllability가 감소하여 수소도핑효과에 의한 carrier 농도가 증가하는 거동의 output curve가 관찰되었다. 60%, 70%의 습도에서 memristive 거동이 관찰되었으며 습도가 높아질수록 on/off ratio는 증가하는 반면 gate controllability가 감소하였다. 60% 습도에서 가장 우수한 특성의 gate tunable memristive 특성을 얻을 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.291.1-291.1
• /
• 2016

Graphene by one of the two-dimensional (2D) materials has been focused on electronic applications due to its ultrahigh carrier mobility, outstanding thermal conductivity and superior optical properties. Although graphene has many remarkable properties, graphene devices have low on/off current ratio due to its zero bandgap. Despite considerable efforts to open its bandgap, it's hard to obtain appropriate improvements. To solve this problem, heterojunction barristor was proposed based on graphene. Mostly, this heterojunction barristor is made by transition metal dichalcogenides (TMDs), such as molybdenum disulfide ($MoS_2$) and tungsten diselenide ($WSe_2$), which have extremely thickness scalability of TMDs. The heterojunction barristor has the advantage of controlling graphene's Fermi level by applying gate bias, resulting in barrier height modulation between graphene interface and semiconductor. However, charged impurities between graphene and $SiO_2$ cause unexpected p-type doping of graphene. The graphene's Fermi level modulation is expected to be reduced due to this p-doping effect. Charged impurities make carrier mobility in graphene reduced and modulation of graphene's Fermi level limited. In this paper, we investigated theoretically and experimentally a relevance between graphene's Fermi level and p-type doping. Theoretically, when Fermi level is placed at the Dirac point, larger graphene's Fermi level modulation was calculated between -20 V and +20 V of $V_{GS}$. On the contrary, graphene's Fermi level modulation was 0.11 eV when Fermi level is far away from the Dirac point in the same range. Then, we produced two types heterojunction barristors which made by p-type doped graphene and graphene treated 2.4% APTES, respectively. On/off current ratio (32-fold) of graphene treated 2.4% APTES was improved in comparison with p-type doped graphene.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.283-283
• /
• 2011

The n-doping effect by doping metal carbonate into an electron-injecting organic layer can improve the device performance by the balanced carrier injection because an electron ohmic contact between cathode and an electron-transporting layer, for example, a high current density, a high efficiency, a high luminance, and a low power consumption. In the study, first, we investigated an electron-ohmic property of electron-only device, which has a ITO/$Rb_2CO_3$-doped $C_{60}$/Al structure. Second, we examined the I-V-L characteristics of all-ohmic OLEDs, which are glass/ITO/$MoO_x$-doped NPB (25%, 5 nm)/NPB (63 nm)/$Alq_3$ (32 nm)/$Rb_2CO_3$-doped $C_{60}$(y%, 10 nm)/Al. The $MoO_x$doped NPB and $Rb_2CO_3$-doped fullerene layer were used as the hole-ohmic contact and electron-ohmic contact layer in all-ohmic OLEDs, respectively, Third, the electronic structure of the $Rb_2CO_3$-doped $C_{60}$-doped interfaces were investigated by analyzing photoemission properties, such as x-ray photoemission spectroscopy (XPS), Ultraviolet Photoemission spectroscopy (UPS), and Near-edge x-ray absorption fine structure (NEXAFS) spectroscopy, as a doping concentration at the interfaces of $Rb_2CO_3$-doped fullerene are changed. Finally, the correlation between the device performance in all ohmic devices and the interfacial property of the $Rb_2CO_3$-doped $C_{60}$ thin film was discussed with an energy band diagram.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.148-149
• /
• 2012

This paper reports doping of carbon atoms in GaN layer, which based on dimethylhydrazine (DMHy) and growth temperature. It is well known that dislocations can act as non-radiative recombination center in light emitting diode (LED). Recently, many researchers have tried to reduce the dislocation density by using various techniques such as lateral epitaxial overgrowth (LEO) [1] and patterned sapphire substrate (PSS) [2], and etc. However, LEO and PSS techniques require additional complicated steps to make masks or patterns on the substrate. Some reports also showed insertion of carbon doped layer may have good effect on crystal quality of GaN layer [3]. Here we report the growth of GaN epitaxial layer by inserting carbon doped GaN layer into GaN epitaxial layer. GaN:C layer growth was performed in metal-organic chemical vapor deposition (MOCVD) reactor, and DMHy was used as a carbon doping source. We elucidated the role of DMHy in various GaN:C growth temperature. When growth temperature of GaN decreases, the concentration of carbon increases. Hence, we also checked the carbon concentration with DMHy depending on growth temperature. Carbon concentration of conventional GaN is $1.15{\times}1016$. Carbon concentration can be achieved up to $4.68{\times}1,018$. GaN epilayer quality measured by XRD rocking curve get better with GaN:C layer insertion. FWHM of (002) was decreased from 245 arcsec to 234 arcsec and FWHM of (102) decreased from 338 arcsec to 302 arcsec. By comparing the quality of GaN:C layer inserted GaN with conventional GaN, we confirmed that GaN:C interlayer can block dislocations.

• 한국결정성장학회지
• /
• 제34권3호
• /
• pp.92-97
• /
• 2024

수소 생산을 위한 물 분해 시스템의 효율성을 높이려면 산소 발생 반응(OER, Oxygen Evolution Reaction)에서 촉매로 인해 발생하는 전기화학 반응의 높은 과전압을 감소시켜야 한다. 그중 전이금속을 포함하는 LDH(Layered Double Hydroxide)와 같은 화합물은 현재 사용되고 있는 백금 등의 귀금속을 대체할 수 있는 촉매 소재로 주목받고 있다. 본 연구에서는 저렴한 금속 다공성 물질인 니켈 폼을 지지체로 사용하였고, 수열합성 공정을 통해 NiCo LDH 나노결정을 합성하였다. 또한, OER 특성을 향상시키기 위해 Mo를 도핑하여 합성한 Mo 도핑된 NiCo LDH 나노결정 시료의 형태, 결정구조, 물분해 특성의 변화를 관찰하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.86-86
• /
• 2012

The new approaches for silicon solar cell of new concept have been actively conducted. Especially, solar cells with wire array structured radial p-n junctions has attracted considerable attention due to the unique advantages of orthogonalizing the direction of light absorption and charge separation while allowing for improved light scattering and trapping. One-dimenstional semiconductor nano/micro structures should be fabricated for radial p-n junction solar cell. Most of silicon wire and/or pillar arrays have been fabricated by vapour-liquid-solid (VLS) growth because of its simple and cheap process. In the case of the VLS method has some weak points, that is, the incorporation of heavy metal catalysts into the growing silicon wire, the high temperature procedure. We have tried new approaches; one is electrochemical etching, the other is noble metal catalytic etching method to overcome those problems. In this talk, the silicon pillar formation will be characterized by investigating the parameters of the electrochemical etching process such as HF concentration ratio of electrolyte, current density, back contact material, temperature of the solution, and large pre-pattern size and pitch. In the noble metal catalytic etching processes, the effect of solution composition and thickness of metal catalyst on the etching rate and morphologies of silicon was investigated. Finally, radial p-n junction wire arrays were fabricated by spin on doping (phosphor), starting from chemical etched p-Si wire arrays. In/Ga eutectic metal was used for contact metal. The energy conversion efficiency of radial p-n junction solar cell is discussed.

• 태양에너지
• /
• 제17권1호
• /
• pp.59-66
• /
• 1997

개방전압과 단락전류와 같은 태양전지 출력변수들은 접합깊이, 도핑농도, 금속접합 및 태양전지구조에 의한 변수들이다. 태양전지 설계의 중요한 요소로서 인이 도핑된 에미터와 금속사이의 금속접합은 일함수 차이가 작아 낮은 직렬저항을 가져야 한다. PESC 태양전지는 금속 접합장벽 전극으로 티타늄을 사용한다. 새로운 접합장벽 전극물질로 티타늄과 일함수가 비슷하지만 전기전도도가 우수한 크롬은 금속 접합장벽 전극으로 유망한 금속이다. 티타늄은 일함수 차가 작지만, 접합장벽으로 크롬은 태양전지 제조시 티타늄보다 우수한 전기적 특성들을 갖는다. 본 논문에서는 실리콘 태양전지의 접합장벽 금속전극의 특성을 비교 분석하였다.