• 한국표면공학회지
• /
• 제49권6호
• /
• pp.549-554
• /
• 2016

Low melting metals are difficult to weld because it is vaporized. But epoxy resin make bonding possible using low melting material and dismissal materials. This study is to improve the bonding strength of epoxy and substrate by mechanical and electrochemical methods. In case of mechanical work, bonding strength is 17.6MPa and in case of pre-work, bonding strength is 15.3MPa. When anodizing and mechanical work is applied, bonding strength is 25.3Mpa is increased 165%. When anodizing is applied, bonding strength is 27.6Mpa.

• 한국전기전자재료학회논문지
• /
• 제24권12호
• /
• pp.949-954
• /
• 2011

In this study, the characteristics and error ranges of the mechanical bonding strength were analyzed according to before and after thermal shock test for various chips of automotive application component using Sn-3.0Ag-0.5Cu solder. In the after thermal shock test, the mechanical bonding strengths tend to decrease, meanwhile decreasing rates of mechanical strengths were less then 12% at specimen's bonding area below 3.5$mm^2$, and were from 17 to 21% at specimen's bonding area above 12 $mm^2$. On the other hand, Specimen's mean deviation rates were about 5% at specimen's bonding area more than 12 $mm^2$. Inversely, at specimen's bonding area is less then 3.5 $mm^2$, mean deviation rates were increased to about 8%. It means that the smaller device size is, the larger mean deviation rate. In addition, error ranges and deviation rates of the mechanical bonding strengths may differ slightly depending on their bonding area. Furthermore, process conditions as well as method of mechanical reliability evaluation should be established to reduce the error ranges of bonding strength.

• 마이크로전자및패키징학회지
• /
• 제31권3호
• /
• pp.91-98
• /
• 2024

This study reveals the feasibility and effectiveness of sinter bonding using an Ag nano-porous sheet at the lowest "theoretically" possible temperature of 145 ℃. By uniform pressure of 10 MPa for bonding times of 5 min and 10 min at 145 and 175 ℃, we achieved bonding strengths exceeding approximately 20 MPa with a only 5 min of bonding time at 145 ℃. In particular, it is interesting to note that in the pressure sintering bonding process at 145 ℃, bonding times of 5 and 10 min had no significant difference in strength. Even with a bonding temperature of 175 ℃, the difference in average bonding strength between bonding times of 5 min (i.e., 37.6 MPa) and 10 min (i.e., 43.0 MPa) was only 5 MPa. The bonding strength was fundamentally attributed to the thickness of the Ag sintered neck in the Ag sintered layer. Microstructural analysis revealed that as the bonding temperature increased to 175 ℃, the fraction of CSL Σ3 boundaries within the Ag sintered layer increased, indicating greater coalescence of Ag particles. This study systematically investigated the mechanism of bonding strength in extremely low-temperature pressure Ag sinter bonding, considering the relationship between microstructures and mechanical behaviors.

• 한국정밀공학회지
• /
• 제27권7호
• /
• pp.21-27
• /
• 2010

The effect of COG bonding parameters, especially the bonding temperature, on the bonding quality and reliability was investigated in this paper. We measured the bubble area formed in the ACF resin during the bonding process and tried to investigate the relationship between bubble area and bonding peel strength. 85/85 test which exposes a sample to a 85% humidity and $85^{\circ}C$ temperature condition was also carried out. The bubble area was dramatically increased under ~$10^{\circ}C$ lower than recommended bonding temperature. The bubble area formed at the edge of IC chip was larger than the other parts of IC chip. But the peel strength was not associated with the bubble area. High temperature and humid condition made the bubble area larger, but we could not find clear trend of change in the peel strength.

• 한국생산제조학회지
• /
• 제26권4호
• /
• pp.430-435
• /
• 2017

The effect of the surface profile on CFRP and aluminum metal bonding was studied. A small number of steps were made on the aluminum surface, and the shear stress and elongation were measured using a shear test after bonding with an autoclave method. As the number of surface steps increased, the shear stress and elongation increased. The surface bonding strength increased because of the effect of the mechanical and chemical bonding. When the number of effective stages was exceeded, the shear strength decreased again due to the aspect ratio of the step and the reduction of the penetration effect of the resin into the groove.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.273-278
• /
• 1998

In this paper, basic micro-mechanical properties of unidirectional CFRP composite shell such as bonding strength, fiber volume fraction and void fraction are measured and tensile strength test is performed with a fixture. And then fracture surfaces are observed by SEM. In case of basic micro-mechanical properties, bonding strength is reduce with decreasing of radius of each ply in a shell for the effect of residual stress, fiber volume fraction is smaller than plate, and void fraction is vise versa. For these reason, tensile strength of shell is smaller than plate fabricated with same prepreg. For failure mode shell has many splitted part along its length, and it is assumed that this phenomenon is caused by the difference of bonding strength for residual stress.

• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1697-1702
• /
• 2000

This study has been performed to investigate the effects of glass fiber characteristics on the mechanical properties of thermoplastic composite. The surface of glass fiber was coated with the silan e to enhance the bonding strength between fiber and matrix. A micro-droplet pull-off test was performed to investigate the influence of the silane concentration on the bonding strength. The maximum bonding strength was observed around 10.8% silane concentration. In order to examine the influence of the fiber length and fiber content on the properties of the composite, the composite materials involving tile fiber lengths of 5mm, 10mm, 15mm 20mm, and 25mm were tested. The composites used contain 20%, 30%, and 40% by weight of glass fibers. Tension and flexural tests were performed to investigate their mechanical properties of the composites. The tensile strength and tensile modulus of the composite increase with increasing the glass fiber content. The tensile modulus increases slightly with increasing the fiber length. The maximum tensile strength is observed around the fiber length of 15-20mm. The flexural modulus and strength also increase slightly with increasing the fiber length.

• 대한기계학회논문집A
• /
• 제25권1호
• /
• pp.11-15
• /
• 2001

We present the design and strength evaluation of an anodically bonded pressurized cavity array, based on the energy release rate measured from the anodically bonded plates of two dissimilar materials. From a theoretical analysis, a simple fracture mechanics model of the pressurized cavity array has been developed. The energy release rate (ERR) of the bonded cavity with an infinite bonding length has been derived in terms of cavity pressure, cavity size, bonding length, plate size and material properties. The ERR with a finite bonding length has been evaluated from the finite element analysis performed for varying cavity and plate sizes. It is found that, for an inter-cavity bonding length greater than the half of the cavity length, the bonding strength of cavity array approaches to that of the infinite plate. For a shorter bonding length, however, the bonding strength of the cavity array is monotonically decreased with the ratio of the bonding length to the cavity length. The critical ERR of 6.21J/㎡ has been measured from anodically bonded silicon-glass plates. A set of critical pressure curves has been generated for varying cavity array sizes, and a design method of the pressurized cavity array has been developed for the failure-free wafer-level packaging of MEMS devices.

• Steel and Composite Structures
• /
• 제31권3호
• /
• pp.233-242
• /
• 2019

Early detection of damage bonding state such as insufficient bonding strength and interface partial contact defect for the explosive clad pipe is crucial in order to avoid sudden failure and even catastrophic accidents. A generalized and efficient model of the explosive clad pipe can reveal the relationship between bonding state and vibration characteristics, and provide foundations and priory knowledge for bonding state detection by signal processing technique. In this paper, the slender explosive clad pipe is regarded as two parallel elastic beams continuously joined by an elastic layer, and the elastic layer is capable to describe the non-uniform bonding state. By taking the characteristic beam modal functions as the admissible functions, the Rayleigh-Ritz method is employed to derive the dynamic model which enables one to consider inhomogeneous system and any boundary conditions. Then, the proposed model is validated by both numerical results and experiment. Parametric studies are carried out to investigate the effects of bonding strength and the length of partial contact defect on the natural frequency and forced response of the explosive clad pipe. A potential method for identifying the bonding quality of the explosive clad pipe is also discussed in this paper.

• 대한기계학회논문집A
• /
• 제26권6호
• /
• pp.1187-1193
• /
• 2002

Anodic bonding process has been quantitatively evaluated based on the Taguchi analysis of the interfacial fracture toughness, measured at the interface of anodically bonded silicon-glass bimorphs. A new test specimen with a pre-inserted blade has been devised for interfacial fracture toughness measurement. A set of 81 different anodic bonding conditions has been generated based on the three different conditions for four different process parameters of bonding load, bonding temperature, anodic voltage and voltage supply time. Taguchi method has been used to reduce the number of experiments required for the bonding strength evaluation, thus obtaining nine independent cases out of the 81 possible combinations. The interfacial fracture toughness has been measured for the nine cases in the range of 0.03∼6.12 J/㎡. Among the four process parameters, the bonding temperature causes the most dominant influence to the bonding strength with the influence factor of 67.7%. The influence factors of other process parameters, such as anodic voltage and voltage supply time, bonding load, are evaluated as 18%, 12% and 2.3%, respectively. The maximum bonding strength of 7.23 J/㎡ has been achieved at the bonding temperature of 460$\^{C}$ with the bonding load of 45gf/㎠, the applied voltage of 600v and the voltage supply time of 25minites.