• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.240-248
• /
• 2016

As a new technical approach, the achievement of an eco-environmental leisure boat with a photovoltaic system is attempted by simultaneously actuating nine photovoltaic solar panels, in association with an applied sail control system by use of wind. In this approach, the photovoltaic system consists of a solar module, an inverter, a battery, and relevant components, while the sail control device is equipped with a sail up/down and mast-turning instrument. Furthermore, this research conducts a performance evaluation of the manufactured prototype and acquires the purposed quantity value and the development purpose items. The significant items-sail up/down speed (seconds) and mast turning angle (degrees)-are evaluated during the performance test. In the process of the performance evaluation, a wind direction sensitivity of 90% and a maximum instant charging power of 900 W were also obtained. In addition, the maximum sail time is evaluated in order to acquire the optimum quantity.

• Journal of The Association for Neo Medicine
• /
• v.1 no.1
• /
• pp.103-113
• /
• 1996

It is thought that the quantity and quality of the heat stimulation and the mechanism of heating process are important to understand the moxa-combustion. In order to get the basic data on the effective moxa-combustion method, combustion temperature changes (average temperature, peak temperature, average gradient temperature and maximum gradient temperature) of the heating period were measured respectively by the density of moxa material. For the experiment, samples of $300mg/0.26cm^3$ , $400mg/0.26cm^3$ and $500mg/0.26cm^3$ of moxa material were molded in a conical mold with each 10mm in diameter and height. 1. The average temperature and peak temperature of heating period on the moxa-combustion showed higher in the $400mg/0.26cm^3$ and $300mg/0.26cm^3$ than in the $500mg/0.26cm^3$ sample respectively. 2. The average gradient temperature of heating period on the moxa-combustion rose quickly in the $300mg/0.26cm^3$, $400mg/0.26cm^3$ and $500mg/0.26cm^3$ in that order and the maximum gradient temperature rose more quickly in the $300mg/0.26cm^3$ and $400mg/0.26cm^3$ than in the $500mg/0.26cm^3$ sample respectively. According to the above results, it is concluded that the density of moxa material is (the) more important (factor) than the weight or volume of moxa material on the combustion temperature changes of the heating period for the evaluation of the quality and quantity of moxa-combustion.

• Journal of Korean Society for Quality Management
• /
• v.50 no.1
• /
• pp.153-167
• /
• 2022

Purpose: The purpose of this study is to guide the operation managers who plan daily production of large mass-processing facility that services multi-customers with multi-product, small-batch item characteristics by providing the practical best production quantity and the inventory allowed to build. Methods: Close observation of a subcontract paint-shop operator captured the daily decision process which was reflected in the subcontractor-unique mathematical model and the system dynamics simulation model. Multiple simulations were run to find the practical best production quantity and the maximum allowable stock level of inventory that did not undermine the profit from practical best daily production. Actual data and a few constant values were obtained from the firm under study. Results: While the inventory holding cost for the customer-owned material harms the total profit of the subcontractor, the running cost of the processing facility hinders production in small batches. This balances the maximum possible productions and results in practical best daily production which can be found through simulation runs with actual data. The maximum level of stocked inventory is deduced from the practical best daily production. Conclusion: To build a large volume that enables economy-of-scale production, operators should deal with multi-product small-batch items from multiple customers. When the planned schedule of the time and amount of material in-flow tend not to be reliable, operators can find it practical to execute level production across the planning horizon instead of adjusting to day-to-day in-flow fluctuations.

• Proceedings of the Society of Korea Industrial and System Engineering Conference
• /
• 2002.05a
• /
• pp.349-357
• /
• 2002

This research is basically deals with an inventory distribution system with several regional sales branches. Under the continuous review policy, each sales branch places an order to its supplier whenever on hand plus on order inventory falls on the order point, and the order quantity is received after elapsing a certain lead time. This research first shows the method how to apply the product with low lever of demand into the continuous review policy. For the application, we use an order level as the maximum level of inventory during an order cycle. Also we analyze the lost sales case as a customer behavior. Further we use variable demands and variable lead times for more realistic situation. Based on the above circumstances, the research mainly discusses those methods to decide the optimal order level, order point, and order quantity for each sales branch which guarantees the system wide goal level of service, while keeping the minimum level of the system wide total inventory.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.94-101
• /
• 2001

In this paper, the combustion improvement effects of alcohol-diesel oil blend fuel were investigated in a visualization engine. As a result of experiment, it was found out that the combustion chamber of deep dish type and re-entrant type at the same operation condition. However, when the con-tent of alcohol exceeded 10% of total fuel delivery, the combustion of alcohol-diesel oil blend fuel was worse than that of diesel oil. The maximum blend quantity of ethanol which is not ignited in the re-entrant type combustion chamber was estimated at approximately 40% of total fuel delivery. So, it is necessary to blend appropriate quantity of a volatility fuel such as alcohol in order to improve combustion.

• Journal of Environmental Science International
• /
• v.11 no.6
• /
• pp.483-488
• /
• 2002

Suspended sediment outflows mainly by natural situation and artificial action and affects in down-stream. This research studied suspended sediments origination in forests size and mountain stream for natural situation, density for artificial action, and measured the size and possible quantity of suspended sediments origination and studied obstruction method of the generation by artificial action. As the result, I found that the size of generation is about 2~3% of forest size and the forest size which is affecting bare area of valley is about 1∼2ha. In addition, possible outflow segments quantity by artificial facilities is assumed to be maximum 200ton/ha and abstract of mountain incline for mountain development needs minimize bare area valley by make right angle with minimum size.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.28-35
• /
• 2002

The objective of this paper is to quantitatively investigate the effects of alcohol mixture on the combustion improvement of main fuel in supplying alcohol to direct injection diesel engine by auxiliary injection method and blend method. If alcohol is supplied, engine performance greatly improves in high load range. In case of supplying ethanol, BSFC improves, the emission of smoke and NO decreases by delaying main fuel injection timing 5$\^{C}$A. The maximum delivery quantity of alcohol is limited to approximately 50% of total fuel delivery due to misfire and knocking. The limit quantity of main fuel injection that does not accompany misfire and the deterioration of BSFC was approximately 15∼18.5mg/st.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.46-51
• /
• 2011

Low temperature vacuum drying technique, whose drying time and quantity of exhausting energy is about 25~30% of hot air drying, is very excellent in the drying efficiency. This paper is made out in the aspects of heat engineering with the object of developing Korean drying machine which can dry once a large quantity of objects to be dried in the state of low temperature and vacuum. As the results, it took about 17 hours(3~4 days in case of hot air drying) for material to reach about 18% of the final moisture content in order to store products for a long time, from about 78~80% of the early moisture content at the beginning of drying, and maximum drying rate comes to about 0.35 kg/m2hr at about 400% of the moisture content.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.363-368
• /
• 2000

This paper is an introduction of pessimum program for the identification of alkali-silica reaction of alkali-aggregate reaction which is known as one of a major factor of concrete deterioration. A series of gel-pat testing program was undertaken to observe the reactivity of potentially alkali-silica reactive concrete aggregates which were found to be reactive by previous petrographic examination (ASTM C 295). And then a pessimum program was performed in accordance with mortar-bar test method (ASTM C 227) with different percentage of those reactive components included in the fine aggregate source to determine the pessimum quantity. Chert and quartzite were found to be major components of reactive mineral/rock, and the pessimum condition for chert was about 3%, even though the test was performed with up to 25% of the component. In the case of quartzite, however, the mortar-bar expansion appeared to be directly proportional to the amount of quartzite sample with increasing tested quantity up to 35%. Both of the expansion results were well 3 and 6 month specified maximum limitation of 0.05% and of 0.1% respectively.

• Journal of Industrial Technology
• /
• v.26 no.B
• /
• pp.43-51
• /
• 2006

Through the result of calculating the deviation between the value calculated from two-dimensional number formula, one-dimensional number interpretation, and curving part water surface type calculation method, we could confirmed that the deviation is reduced more than 50% when we use curving part water surface type calculation method. Also it was confirmed that there occurs the reduction rate of maximum 59% as the result of comparing with one-dimensional number interpretation since the reduction rate of safe room height was 20%, in 500 CMS of flood water quantity when we planted the construction of levee by curving part water surface type calculation method. And therefore, we have confirmed that the curving water surface type calculation method can be used as a simple formula in rivers with water quantity less than 500 CMS that flows in and out in Jess than 90 degree angle.