• Korean Journal of Digital Imaging in Medicine
• /
• v.9 no.1
• /
• pp.37-43
• /
• 2007

1. Purpose : This study is to present effective exposure conditions to acquire the best image of simple abdomen in Film Screen (F.S) system and Computed Radiography (C.R) system. 2. Method : In the F.S system, while an exposure condition was fixed as 70kVp, images of a patients simple abdomen were taken under the different mAs exposure conditions. Among these images, the best one was chosen by radiologists and radiological technologists. In the C.R system, the best image of the same patient was acquired with the same method from the F.S system. Both characteristic curves from F.S system and C.R system were analyzed. 3. Results : In the F.S system, the best exposure condition of simple abdomen was 70kVp and 20mAs. In the CR system, with the fixed condition at 70kVp, the image densities of human organs, such as liver, kidney, spleen, psoas muscle, lumbar spine body and iliac crest, were almost same despite different environments (3.2mAs, 8mAs, 12mAs, 16mAs and 20mAs). However, when the exposure conditions were over or under (below) 12mAs, the images between the abdominal wall and the directly exposed part became blurred because the gap of density was decreased. In the C.R system, while the volume of mAs was decreased, an artifact of quantum mottle was increased. 4. Conclusion : This study shows that the exposure condition in the C.R system can be reduced 40% than in the F.S system. This paper concluded that when the exposure conditions are set in CR environment, after the analysis of equipment character, such as image processing system(EDR : Exposure Data Recognition processing), PACS and so on, the high quality of image with maximum information can be acquired with a minimum exposure dose.

• IE interfaces
• /
• v.21 no.3
• /
• pp.254-261
• /
• 2008

Connected-(r,s)-out of-(m,n) : F system is an important topic in redundancy design of the complex system reliability and it's maintenance policy. Previous studies applied Monte Carlo simulation and genetic, simulated annealing algorithms to tackle the difficulty of maintenance policy problem. These algorithms suggested most suitable maintenance cycle to optimize maintenance pattern of connected-(r,s)-out of-(m,n) : F system. However, genetic algorithm is required long execution time relatively and simulated annealing has improved computational time but rather poor solutions. In this paper, we propose the ant colony optimization approach for connected-(r,s)-out of-(m,n) : F system that determines maintenance cycle and minimum unit cost. Computational results prove that ant colony optimization algorithm is superior to genetic algorithm, simulated annealing and tabu search in both execution time and quality of solution.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.90-98
• /
• 1998

A Dual Mass Flywheel(D.M.F.) system is an evolution to the reduction of torsional vibration and impact noise occurring in powertrain when a vehicle is either moving or idling. The D.M.F. system has two flywh-eels, which is different from the conventional clutch system. One section belongs to the mass moment of in-ertia of the engine-side. The other section increases the mass moment of inertia of the transmission-side. These two masses are connected via a spring/damping system. This reduces the speed at which the dreaded resonance occurs to below idle speed. Since 1984m D.M.F. system has been developed. However, the processes of development of D.M.F. system don't have any difference from the trial and error method of conventional clutch system. This paper present the method for systematical design of D.M.F. system with dimensionless design varia-bles of D.M.F. system, mass ratio between two flywheels, natural frequency rate of two flywheels, and visc-osity coefficient. And expermental results are used to prove these theoretical results.

• Journal of the Korean Society of Costume
• /
• v.51 no.4
• /
• pp.43-56
• /
• 2001

Articles on fashion of major daily newspapers for about one years after I.M.F. system were analyzed. The influence of I.M.F. system, values, the importance of costumes at economic crisis were studied through fashion at that time. The major conclusions of the study are as follows : 1. Costumes made in Korea, national brands In Korean words, practical styles, multi-functional design, economic tastes and mixed fashions were emphasized. 2. The sound and patriotic values were pursued through domestic fashion and creative ideas were developed to overcome economic crisis. 3. The meaning of costumes was still important under shrink of consumption. Costumes were useful tools to estimate ability and express aesthetic appreciation. The sound fashion trends under I.M.F. system reflect the reflection on overconsume and the will to overcome economic crisis. Such trends should be fixed for the establishment of economic prosperity for the nation.

• Korean Journal of Digital Imaging in Medicine
• /
• v.12 no.2
• /
• pp.133-138
• /
• 2010

The purpose of this study was to survey and test quality control of mammography system. The conclusion of this study is as follows ; First, The rate of pass for phantom image test shows that Film-Screen mammography system(F/S) and computed mammography system(CR) is 80%, Indirect digital mammography system(DR) is 100%. Second, The test of exposure dose shows that F/S is 921 mR. CR is 1,140 mR, DR is 474 mR. The grade of this testament is CR > F/S > DR. Third, The test of average glandular dose shows that F/S is 1,336 mGy, CR is 1,635 mGy, DR is 1,26 mGy. The grade of this testament is CR > F/S > DR. Fourth, The testament of resolution shows as follows F/S is 11~13 Lp/mm, CR is 4~5 Lp/mm, and DR is 5~7 Lp/mm(F/S > DR > CR) Fifth, The survey of projection, cassette, development and reading shows that user are indifference.

• The korean journal of orthodontics
• /
• v.29 no.5 s.76
• /
• pp.511-519
• /
• 1999

The shape of orthodontic retraction spring was varied and force system of each case was obtained using numerical analysis and verified with spring tester. The factors for obtaining biomechanically efficient spring under anatomic limitation were suggested as follows. 1. M/F ratio increases and L/D rate decreases as loop height increases. 2. M/F ratio increases and L/D rate decreases as incorporating more wire above minimum bending moment area. 3. M/F ratio decreases and L/D rate decrease as incorporating more wire below minimum bending moment area. 4. M/F ratio can not be greater than spring height no matter how much wire is incorporated at the apex of the loop. 5. Additional moment is necessary to obtain enough M/F ratio for translation under anatomical limitation. 6. Additional moment should be incorporated at every pah of the spring because M/F ratio and L/D rate decreases as horizontal spring length increases. 7. Material, cross section, and shape of the spring influence L/D rate, whereas M/F ratio is influenced by the shape of the spring independent from material and cross section.

• Communications of the Korean Mathematical Society
• /
• v.12 no.3
• /
• pp.491-497
• /
• 1997

Let $C(F, M)$ and $C(S^{-1}F, S^{-1}M)$ be Cousin complexes for a modula M and a module $S^{-1}M$ over a commutative Noetherian ring with respect to a filtration F and a filtration $S^{-1}F$ respectively. In this paper, it is shown that there is an isomorphism between the Cousin complexes $S^{-1}C(F, M)$ and $C(S^{-1}F, S^{-1}M)$.

• 전기의세계
• /
• v.15 no.2
• /
• pp.1-7
• /
• 1966

It is well known that the speed of induction motor can be controlled in wide range by changing the second exciting e.m.f. of rotor circuit, but that is well not practised because of its complicated system. In order to simplify such a system, the Kramer system of which silicon rectifier substitutes for synchronous converter has analyzed in this paper. The result of this investigation show that in this system, only the equivlent synchronous speed it changed by second exciting e.m.f., but the mechanical output power, torque and power factor is not changed, and that this system is able to compensate the regulated speed on account of the load changed.

• Journal of Astronomy and Space Sciences
• /
• v.26 no.4
• /
• pp.643-650
• /
• 2009

Korea Astronomy and Space Science Institute (KASI) has been developing one mobile and one stationary SLR system since 2008 named as ARGO-M and ARGO-F, respectively. KASI finished the step of deriving the system requirements of ARGO. The requirements include definitions and scopes of various software and hardware components which are necessary for developing the ARGO-M operation system. And the requirements define function, performance, and interface requirements. The operation system consisting of ARGO-M site, ARGO-F site, and Remote Operation Center (ROC) inside KASI is designed for remote access and the automatic tracking and control system which are the main operation concept of ARGO system. To accomplish remote operation, we are considering remote access to ARGO-F and ARGO-M from ROC. The mobile-phone service allows us to access the ARGO-F remotely and to control the system in an emergency. To implement fully automatic tracking and control function in ARGO-F, we have investigated and described the requirements about the automatic aircraft detection system and the various meteorological sensors. This paper addresses the requirements of ARGO Operation System.

• Bulletin of the Korean Mathematical Society
• /
• v.50 no.2
• /
• pp.485-498
• /
• 2013

In this paper, the Schur convexity is generalized to Schur $f$-convexity, which contains the Schur geometrical convexity, harmonic convexity and so on. When $f$ : ${\mathbb{R}}_+{\rightarrow}{\mathbb{R}}$ is defined as $f(x)=(x^m-1)/m$ if $m{\neq}0$ and $f(x)$ = ln $x$ if $m=0$, the necessary and sufficient conditions for $f$-convexity (is called Schur $m$-power convexity) of Gini means are given, which generalize and unify certain known results.