• 한국응용과학기술학회지
• /
• 제24권4호
• /
• pp.347-353
• /
• 2007

Fleshing scrap is a kind of wastes produced during leather making process and used in the test of manufacturing biodiesel. The early step of manufacturing biodiesel is fat recovery from fleshing scrap. Hence, we investigated the influence of the way of fat recovery on the fatty acid composition. We used three different recovery ways, that is chemical method by protein decomposition with acid/fat recovering, physical method by protein denaturalization with heat and vacuum/fat pressing, and biodiesel method by protein decomposition/fat recovering. The biological method yielded the best results in terms of appearance transparency. It was most effective to lower acid value. Also the recovered fat by biological method would be favorable methyl-ester reaction raw material for biodiesel because it contains more than 5% of oleic acid among unsaturated fatty acid.

• 한국식생활문화학회지
• /
• 제30권3호
• /
• pp.370-376
• /
• 2015

In this study, we compared the organoleptic and other qualities of fermented milk containing 10 or 15% purple carrot extract that had either been previously fermented with Aspergillus oryzae or not fermented. Fermentation characteristics, pH, chromaticity, viscosity, viable cell counts, and sensory evaluations were measured. The pH and acid values did not differ between purple carrot extract fermented with Aspergillus oryzae and non-fermented extract. Viable cell counts were significantly higher in 15% purple carrot extract fermented with Aspergillus oryzae compared to the control after fermentation. Regarding characteristic changes, purple carrot extract fermented with Aspergillus oryzae group showed a lower red value but higher yellow value compared with non-fermented purple carrot extract due to heat-sterilization. Both fermented and non-fermented extract groups showed significantly increased viscosity compared to control. In the sensory evaluation, 15% purple carrot extract fermented with Aspergillus oryzae showed the highest score. In conclusion, addition of 15% purple carrot extract fermented with Aspergillus oryzae resulted in a superior fermented milk product.

• 한국의류산업학회지
• /
• 제9권3호
• /
• pp.347-350
• /
• 2007

To analyse basic properties for making packing batt according to doubling condition, packing batt yarn, of $300^D$, $900^D$, $3600^D$ made from DTY yarn $150^D$/48 were produced from KTDI. The results are as follows: The birefringence of the sample yarn increased with increasing the annealing temperature and denier. The initial modulus of the sample yarn decreased with increasing the annealing temperature and denier. The higher than annealing temperature of $160^{\circ}C$, initial modulus of the sample are equilibrated. The strain recovery ratio of samples decreased with increasing the annealing temperature and denier. The lower than annealing temperature of $140^{\circ}C$, strain recovery ratio of the sample are decreased Where the $900^D$, $3600^D$ yarns are at $100^{\circ}C$ the specific bending rigidity value obtained is 0.65kgf/d but the twisted yarn (3,600) obtained 0.006 ($gfcm^2/tex^2$). However, where the heat temperature is $160^{\circ}C$, specific bending rigidity value obtained 0.003($gfcm^2/tex^2$).

• 한국연소학회지
• /
• 제18권3호
• /
• pp.44-53
• /
• 2013

In this study, the economic evaluation for imported coals was conducted for power plant based on thermo-dynamical performance analysis. The number of coal types considered was 1,755 imported by five power generation companies in Korea during the 2010-2012. The higher heating value (HHV) of the coals ranged 4,000-6,500 kcal/kg, mostly sub-bituminous. The 1D thermo-dynamical performance modeling was performed for a 500 MWe standard power plant using PROATES code. It was founded that the low rank coals had negative effects on the plant efficiency mainly due to the increased heat loss by moisture, hydrogen and flue gas. Based on the performance analysis, the economic performance of the coals was evaluated. The apparent price of low-rank coals tended to be significantly lower than design coal; for example, the unit price of coal with a HHV of 4,000 kcal/kg was 57% of the reference coal having 6,080 kcal/kg. Considering the negative effects leading to a decrease in the thermal performance, heating value compensation, and increased parasite load, the corrected unit cost for the coal with 4,000 kcal/kg was 90.7% of the reference coal. Overall, the cost saving by imported coals was not high as expected.

• 한국연소학회지
• /
• 제14권3호
• /
• pp.29-36
• /
• 2009

Simulation is performed to analyze the characteristics of turbulent spray combustion in a diesel engine condition. An extended Conditional Moment Closure (CMC) model is employed to resolve coupling between chemistry and turbulence. Relevant time and length scales and dimensionless numbers are estimated at the tip and the mid spray region during spray development and combustion. The liquid volume fractions are small enough to support validity of droplets assumed as point sources in two-phase flow. The mean scalar dissipation rates (SDR) are lower than the extinction limit to show flame stability throughout the combustion period. The Kolmogorov scales remain relatively constant, while the integral scales increase with decay of turbulence. The chemical time scale decreases abruptly to a small value as ignition occurs with subsequent heat release. The Da and Ka show opposite trends due to variation in the chemical time scale. More work is in progress to identify the spray combustion regimes.

• 전기학회논문지P
• /
• 제58권1호
• /
• pp.67-71
• /
• 2009

This research is a new structure of the semiconductor substrate heating apparatus in which the assembly and expansion are possible. The fast thermo-responsive according to the direct heating structure of the heating plate layer adhering closely to the floor side of a substrate and the fast heat loss minimization can be accomplished. Moreover, the contact area of the sheath heater, which is the heating plate layer built-in heating apparatus, is increased, so that it has more heating valid area. There is no problem with the deformation interpreted in the state where it assembles the block of a several of the simulation result structure, the safety, and the stress. In addition, it is confirmed that building a large-size heating block is possible since the temperature deflection of the manufactured plate is lower than the standard value.

• 한국세라믹학회지
• /
• 제48권1호
• /
• pp.14-19
• /
• 2011

Microwave heating (MW) was studied for the sintering of amorphous powders. In comparison to conventional heating (CV), the results show that microwave heating has the potential to substantially accelerate the sintering process and allow for highly densified solidification by eliminating the pores and increasing the shrinkage rate. In the heat treatment to synthesize aluminum borate ($Al_{18}B_4O_{33}$) whiskers from precursors, it was found that microwave heating helps the formation of $Al_{18}B_4O_{33}$ crystal as well as the decrease of crystallization temperature of $Al_{18}B_4O_{33}$ to a level significantly lower than the previously reported value of $1050^{\circ}C$.

• 동력기계공학회지
• /
• 제14권4호
• /
• pp.5-10
• /
• 2010

This study was investigated the effect on operating characteristics of apparatus according to frosting and defrosting to develop of new defrosting equipment. The results showed as following. Frost was almost removed using the defrosting equipment with roll brush type that defrosting is possible under operating condition. Also, the temperature of compressor inlet, evaporator inlet and outlet showed higher value because of heat transfer resistance of cooling pipe frost comparing with defrosting condition. And the compressor work showed 10% lower and COP was presented 24% higher values than defrosting condition. Therefore, defrosting for cooling coil of refrigeration and low temperature storage was effected on operation and performance characteristics of equipment. This highly effects on real refrigeration apparatus which is operated in year-around.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.2107-2112
• /
• 2010

To analyze the effect of temperature on pavement types of dedicated lane, we have performed a temperature monitoring for pavements which were constructed in test track for Bimodal Tram. These pavements classified into four types; natural and artificial lawn, concrete and asphalt. Dedicated lane composed of natural and artificial lawn has a complex structure with concrete slab in contact surface of tires, and with 1m natural or artificial lawn in the middle part of lane. From monitoring results for pavements, dedicated lane with natural lawn shows lower temperature value compared with other dedicated lanes, and it is expected to decrease the heat island effect of conventional road if constructed.

• 한국표면공학회지
• /
• 제42권1호
• /
• pp.34-40
• /
• 2009

In the study, it was carried out dissimilar metal welding on materials for Al ship. The electrochemical and mechanical characteristics evaluated for specimen welded by ROBOT. The hardness of welding zone is lower than those of heat affected zone and base metal. At the result of tensile test, the specimen welded with ER5183 welding material presented excellent property compared with ER5556. The polarization trend for the base metal and welding metal showed the effects of concentration polarization due to oxygen reduction and activation polarization due to hydrogen generation. At the Tafel experiments result, the corrosion density in welded with ER5183 welding material presented the lowest value.