• Korean Journal of Applied Biomechanics
• /
• v.13 no.1
• /
• pp.95-108
• /
• 2003

The purposes of this study were to analyze the muscle activities and the characteristics of muscle recruiting patterns of upper trunk for Ssirum dutguri technique using three top-ranked elite Ssirum players. The EMG technique was used to record muscle activities of both right and left sides of latissimus dorsi, biceps brachii, and erector spinae. Six surface electrodes were placed on the surface of the selected muscles and one ground electrode was also attached on the back of neck(C7). One video camera was also used to record the Ssirum motion to define 4 events and 3 phases for further analysis. The raw EMG data were filtered with band pass filter (50-400 Hz) to remove artifacts and then low pass filtered (4 Hz) to find the linear envelope which resemble muscle tension curve. This filtered EMG data were normalized to MVIC for the purpose of comparion between the subjects. The results were indicated that each subject with different physical characteristics showed very different muscle activity patterns. Although Ssirum dutguri is considered as foot technique the player grasped opponent's satba(belt) with both hands when they play. Because of this reason, activities of upper trunk muscles were relatively high. However, direct comparison between upper and lower body muscles was not possible due to the lack of the data in present study. Interestingly, all threes subjects showed that erector spinae muscle activity was comparatively higher than those of latissimus dorsi and biceps brachii. This implies to reinforce back muscle as a routine of training to improve performance or to prevent back injury.

• Clean Technology
• /
• v.10 no.2
• /
• pp.61-72
• /
• 2004

In this study, aqueous/semi-aqueous cleaning agents which consist of organic solvent, surfactant, cosurfactant, and water were developed by changing formulation parameters such as organic solvent type and contents, surfactant type and contents, and cosurfactant/surfactant(A/S) ratio, etc.. And physical properties and flux removal of the formulated cleaning agents have been evaluated. Also, the performance of oil-water separation from the rinse water contaminated during the cleaning process was evaluated for its recycling. The formulated cleaning agents in this work expected to have good penetration because of their low viscosity and low surface tension values of 30.2~32.5 dyne/cm. The flux removal with the terpene type cleaning agent was higher than that with hydrocarbon type cleaning agent and two commercial products (CPA(commercial product A), CPB(commercial product B)). And the performance of oil-water separation by gravity settling from the rinse water contaminated with formulated cleaning agent and soils was shown to be very good. The cleaning agents developed in this work were applied to surface mounting technology(SMT) cleaning process for manufacturing electronic parts at L electronic company. As a result, the newly developed cleaning agents showed two times better cleaning speed for removal of solder cream than the conventional ond containing ethanol and IPA(isopropyl alcohol). In addition, malodor and VOC problems generated by the previous organic cleaning agents have been solved in the manufacturing field through introduction of the non-volatile and environmental-friendly cleaning agents to the field.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.80-87
• /
• 2010

The purpose of this paper is to analyze the effects of ethanol blending ratio and fuel temperature in diesel-ethanol blended fuel on the spray-atomization characteristics in a high pressure common-rail injection system. In this work, a diesel fuel and three blended fuels were used as test fuels. Blended fuels were made by blending ethanol with a purity 99.9% to diesel fuel, from 0% to 30%. In order to keep diesel-ethanol blending stability, 5% of biodiesel fuel as volumetric ratio was added into test fuels. The fuel temperature was controled in steps with 40K, from 290K to 370K. Macroscopic spray characteristics were investigated by analyzing the spray tip penetration and spray cone angle through spray images obtained from visualization system. In addition, in order to study microscopic spray characteristics of ethanol blended fuels, the droplet diameter, was analyzed using the droplet measuring system. It is revealed that the spray tip penetration is similar regardless of ethanol blending ratio. As ethanol blending ratio is increased, the spray cone angle becomes wider. It is shown that the spray cone angle is affected by low viscosity and density of ethanol. As the fuel temperature increases, the spray tip penetration and spray cone angle become shorter and narrower respectively. The SMD of ethanol blending fuels is smaller than that of diesel fuel because of low viscosity and surface tension of ethanol.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.1
• /
• pp.143-150
• /
• 2014

Recently, supercritical fluid process has been widely used in material synthesis and processing due to their remarkable properties such as high diffusivity, low viscosity, and low surface tension. Supercritical carbon dioxide is the most attractive solvent owing to their characteristics including non-toxic, non-flammable, chemically inert, and also it has moderate critical temperature and critical pressure. In addition, supercritical carbon dioxide would dissolve many small organic molecules and most polymers. In this study, we have prepared the poly (ethylene oxide)/clay nanocomposites using supercritical fluid as a carbon dioxide. Commercialized Cloisites-15A and Cloisites-30B used in this study, which are modified with quaternary ammonium salts. The nanocomposites of polymer/clay were characterized by XRD, TGA and DSC. Poly (ethylene oxide)/clay nanocomposites by supercritical fluid show higher thermal stability than nanocomposites prepared by melt process. In addition, supercritical fluid process would be increased dispersibility of the nanoclay in the matrix.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.21-27
• /
• 2022

Flexible pressure sensor was developed using low-cost conductive graphite as printed electronics. Flexible pressure sensors are attracting attention as materials to be used in future industries such as medical, games, and AI. As a result of evaluating various electromechanical properties of the printed electrode for flexible pressure sensors, it showed a constant resistance change rate in a maximum tensile rate of 20%, 30° tension/bending, and a simple pulse test. A more appropriate matrix pattern was designed by simulating the electrodes for which this verification was completed. Utilizing the Serpentine pattern, we utilized a process that allows simultaneous fabrication and encapsulation of the matrix pattern. One side of the printed graphite electrode was O₂ plasma surface treated to increase adhesive strength, rotated 90 times, and two electrodes were made into one through a lamination process. As a result of pasting the matrix pattern prepared in this way to the wrist pulse position of the human body and proceeding with the actual measurement, a constant rate of resistance change was shown regardless of gender.

• Journal of the Korea Concrete Institute
• /
• v.20 no.2
• /
• pp.131-138
• /
• 2008

Humidity and strain were estimated for understanding the relation between humidity change by self-desiccation and shrinkage in high-performance concrete with low water binder ratio. Internal humidity change and shrinkage strain were about 10%, 4% and $320\times10^{-6}$, $120\times10^{-6}$ respectively on concrete with water binder ratio 0.3, 0.4 and from the results, humidity change and shrinkage represented the strong linear relation regardless of mixture. For specifying the relation on internal humidity change and autogenous shrinkage strain, shrinkage model was established which is driven by capillary pressure in pore water and surface energy in hydrates on the assumption of a single network and extended meniscus in pore system of concrete. This model and experimental results had a similar tendency so it would be concluded that the internal humidity change by self-desiccation in HPC originated in small pores less than 20 nm, therefore controlling plan on autogenous shrinkage might be focused on surface tension of water and degree of saturation in small pore.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.2
• /
• pp.231-237
• /
• 2014

The supercritical fluids (SCFs) have been widely used for material synthesis and processing due to their remarkable properties including low viscosity, high diffusivity and low surface tension. Carbon dioxide is one of the suitable solvents in SCFs processes in terms of its advantages such as easy processibility (with low critical temperature and pressure), inexpensive, nonflammable, nontoxic, and readily available. However, it has generally low solubility for high molecular weight polymers with the exception of fluoropolymers and siloxane polymers. Therefore, hydrocarbon solvents and hydrochlorofluorocarbons have been used for various SCFs process by its high solubility for high molecular weight polymers. In this report, a PMMA/clay nanocomposites were fabricated by using supercritical fluid process. The $Na^+$-MMT(montmorillonites)was modified by a fluorinated surfactant which is able to enhance compatibility with the chlorodifluoromethane(HCFC-22) and thus, improve dispersability of the clay in the polymer matrix. The PMMA/fluorinated surfactant modified clay nanocomposite shows enhanced mechanical and thermal properties which characterized by X-raydiffraction(XRD), Thermo gravimetric analysis(TGA), Dynamic mechanical analysis (DMA) and Transmission electron microscopy (TEM).

• Journal of Environmental Health Sciences
• /
• v.42 no.2
• /
• pp.112-117
• /
• 2016

Objectives: In this study, we investigated the biodegradation rates of 8 perfluorooctanesulfonate (PFOS) alternatives synthesized at the at Changwon National University in comparison to those of PFOS potassium salt and PFOS sodium salt. Methods: A biodegradability test was performed for 28 days with microorganisms cultured in the good laboratory practice laboratory at the Korea Environment Corporation following the OECD Guidelines for the testing of chemicals, Test No. 301 C Results: While $C_5H_8F_3SO_3K$, $C_8F_{17}SO_3K$ and $C_8F_{17}SO_3Na$ were not degraded after 28 days, the 3 alternatives were biodegraded at the rates of 31.4% for $C_8H_8F_9SO_3K$, 25.6% for $C_{10}H_8F_{13}SO_3K$, 23.6% for $C_{25}F_{17}H_{32}S_3O_{13}Na_3$, 20.9% for $C_{15}F_9H_{21}S_2O_8Na_2$, 15.5% for $C_{23}F_{18}H_{28}S_2O_8Na_2$, 8.5% for $C_{17}F_9H_{25}S_2O_8Na_2$ and 4.8% for $C_6H_8F_5SO_3K$. When the concentration was the same(500 mg/L), $C_{23}F_{18}H_{28}S_2O_8Na_2$ had the lowest tension with 20.94 mN/m, which was followed by $C_{15}F_9H_{21}S_2O_8Na_2$ (23.36 mN/m), $C_{17}F_9H_{25}S_2O_8Na_2$ (27.31 mN/m), $C_{25}F_{17}H_{32}S_3O_{13}Na_3$ (28.17 mN/m), $C_{10}H_8F_{13}SO_3K$ (29.77 mN/m) and $C_8H_8F_9SO_3K$ (33.89 mN/m). Having higher surface tension of 57.64 mN/m and 67.57 mN/m, respectively, than those of the two types of PFOS salts, $C_6H_8F_5SO_3K$ and $C_5H_8F_3SO_3K$ were found valueless as substitute for PFOS. Conclusion: The biodegradation test suggest that 6 compounds could be used as substitutes for PFOS. $C_{23}F_{18}H_{28}S_2O_8Na_2$ and $C_{15}F_9H_{21}S_2O_8Na_2$ were found to be the best substitutes based on biodegradation rate and surface tension, followed by $C_{25}F_{17}H_{32}S_3O_{13}Na_3$, $C_8H_8F_9SO_3K$ and $C_{10}H_8F_{13}SO_3K$. $C_{17}F_9H_{25}S_2O_8Na_2$ was found to have relatively low value as an alternative but it still had a potential to substitute the conventional PFOS.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.2
• /
• pp.103-109
• /
• 2009

Soils originated from limestone, located at the southern part of Kangwon province and Jecheon, Danyang of Chungbuk province are mainly composed of fine texture, and have different properties from soils originated from granite and granite gneiss, especially for water movement. This study was conducted for classification of hydrologic soil group (HSG) of soils originated from limestone by measuring the infiltration rate of surface soils and percolation rate of sub soils. Soils used for the experiment were 6 soils in total : Gwarim, Mosan, Jangseong, Maji, Anmi and Pyongan series. Infiltration and percolation rate were measured by a disc tension infiltrometer and a Guelph permeameter, respectively. Particle size distribution and organic matter content of the soils were analyzed. HSG, which was made by USDA NRCS(National Resources Conservation Service) for hydrology, of Gwarim series with O horizon of accumulated organic matter was classified as type A which show the properties of low runoff potential, rapid infiltration and percolation rate. HSG of Mosan series, which has high gravel content and very rapid permeability, was classified as type B/D because of the impermaeble base rock layer under 50cm from surface. HSG of Jangseong series with shallow soil depth was classified as type C/D owing to the impermaeble base rock layer under 50cm from surface. HSG of Maji series was type B, and HSG of Anmi series used as paddy land was type D because of slow infiltration and percolation rate caused by the disturbance of surface soil by puddling. HSG of Pyeongan series having a sudden change of layer in soil texture was type D because of the slow percolation rate caused a the layer.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.3
• /
• pp.19-31
• /
• 2007

Humidity and strain were estimated for understanding the relation between humidity change by self-desiccation and shrinkage in high-performance concrete with low water binder ratio and containing fly ash and blast furnace slag. Internal humidity change and shrinkage strain were about 10%, 10%, 7%, 11%, 11% and $320{\times}10^{-6}$, $270{\times}10^{-6}$, $231{\times}10^{-6}$, $371{\times}10^{-6}$, $350{\times}10^{-6}$ respectively on OPC30, O30F10, O30F20, O30G40, O30G50 and from the results, fly ash made humidity change and strain decrease but slag increase comparing with ordinary portland cement. Considering only relation internal humidity and shrinkage by self-desiccation, humidity change and shrinkage represented the strong linear relation regardless of mineral admixture. For specifying the relation on internal humidity change and autogenous shrinkage strain, shrinkage model was established which is driven by capillary pressure in pore water and surface energy in hydrates on the assumption of a single network and extended meniscus in pore system of concrete. This model and experimental results had a similar tendency so it would be concluded that the internal humidity change by self-desiccation in HPC originated in small pores less than 20nm, therefore controlling plan on autogenous shrinkage might be focused on surface tension of water and degree of saturation in small pore.