• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.4
• /
• pp.568-576
• /
• 2017

This paper presents a clock and data recovery circuit with an adaptive loop bandwidth calibration scheme and the idle power saved frequency acquisition. The loop bandwidth calibration adaptively controls injection currents of the main loop with a trimmable bandgap reference circuit and trains the VCO to operate in the linear frequency control range. For stand-by power reduction of the phase detector, a clock gating circuit blocks 8-phase clock signals from the VCO and cuts off the current paths of current mode D-flip flops and latches during the frequency acquisition. 77.96% reduction has been accomplished in idle power consumption of the phase detector. In the jitter experiment, the proposed scheme reduces the jitter tolerance variation from 0.45-UI to 0.2-UI at 1-MHz as compared with the conventional circuit.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.1C
• /
• pp.40-44
• /
• 2010

The timing error detector(TED) employed in the closed loop type timing synchronization scheme for an MQASK all digital receiver suffers from the selfnoise-induced timing jitter. To eliminate the timing jitter a prefilter can be added in front of the TED. The prefilter method, however, degrades the stability and timing acquisition performance due to the loop delay and increases the complexity of the synchronizer. This paper proposes a polyphase filter type resampler approach to optimize the performance and architecture of the synchronizer simultaneously. The proposed scheme uses two resamplers which performs matched filtering and matched prefiltering so that the loop delay is minimized with minimal hardware resources. Simulation results showed an excellent acquisition performance with reduced timing jitter.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.7
• /
• pp.545-551
• /
• 2013

Timing recovery loop composed of the Timing Error Detector(TED), loop filter and resampler is widely used for the timing synchronization in MQASK receivers. Since TED is sensitive to the delay between the symbol period of the signal and sampling period, the output is averaged out when the symbol rate and sampling rate are quite different the recovery loop cannot work at all. This paper presents a sampling frequency discriminator (SRD), which detects the frequency offset of the sampling clock to the symbol clock of the MQASK data transmitted. Employing the SRD, the closed loop timing recovery scheme performs the frequency-aided timing acquisition and achieve the synchronization at extremely high sampling frequency offset, which can be used in variable symbol rate MQASK receivers.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1643-1647
• /
• 2003

This paper, we propose a new high noise immunity phase-locked loop(PLL) which can suppress the high incident noise coupling with large amplitude and long period to the input frequency of PLL and keeps constant frequency and phase of the VCO output for providing the high stability distribution clock pulse.

• Journal of Korean Society of Transportation
• /
• v.14 no.1
• /
• pp.135-154
• /
• 1996

This paper presents a heuristic algorithm for classifying vehicles using a single loop detector. The data used for the development of the algorithm are the frequency variation of a vehicle sensored from the circle-shaped loop detectors which are normal buried beneath the expressway. The pre-processing of data is required for the development of the algorithm that actually consists of two parts. One is both normalization of occupancy time and that with frequency variation, the other is finding of an adaptable number of sample size for each vehicle category and calculation of average value of normalized frequencies along with occupancy time that will be stored for comparison. Then, detected values are compared with those stored data to locate the most fitted pattern. After the normalization process, we developed some frameworks for comparison schemes. The fitted scales used were 10 and 15 frames in occupancy time(X-axis) and 10 and 15 frames in frequency variation (Y-axis). A combination of X-Y 10-15 frame turned out to be the most efficient scale of normalization producing 96 percent correct classification rate for six types of vehicle.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.3
• /
• pp.352-358
• /
• 2016

A 5-phase phase-locked loop (PLL) for USB2.0 applications was implemented by using an all-synthesis technique. The length of the time-to-digital converter for the fine phase detector was halved by the operation of a coarse phase detector that uses 5-phase clocks. The maximum time difference between the rising edges of two adjacent-phase clocks was 6 ps at 480 MHz. The PLL chip in a 65-nm process occupies $0.038mm^2$, consumes 4.8 mW at 1.2 V. The measured rms and peak-to-peak output jitters are 8.6 ps and 45 ps, respectively.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.163-166
• /
• 1999

In this paper, frequency synthesizer that can be used in IMT-2000 was designed and fabricated using dual loop PLL(Phase Locked Loop). For improving phase noise characteristic Voltage Controlled Oscillator was fabricated using coaxial resonator and eliminated frequency divider using SPD as phase detector and increased open loop gain. Fabricated frequency synthesizer had 1.82㎓ center frequency, 160MHz tuning range and -119.73㏈c/Hz low phase noise characteristic.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.14 no.2
• /
• pp.14-23
• /
• 2015

This study was intended to evaluate the feasibility of the vehicle detector using a coil sensor. For the evaluation, the research team built a test environment for the detector consisting of a oscillation circuit, data collecting circuit, data monitoring and saving circuit, etc. As the result of the frequency analysis of the detector from the test environment, it was verified for the detector using a coil sensor to generate stable frequencies. In addition, the ease of construction and management was tested by comparing the size of cutting areas, consumption of installation materials, and installation time for a traditional loop detector and the detector using a coil sensor. As a result, the installation of the detector using a coil sensor requires less size of cutting areas, consumption of installation materials, and installation time.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.7 no.3
• /
• pp.55-61
• /
• 2011

This paper presents an implementation of Lattice Reduction (LR)-aided detector for Multiple-Input Multiple-Output (MIMO) system using Graphics Processing Unit (GPU). GPU is a parallel processor which has a number of Arithmetic Logic Units (ALUs), thus, it can minimize the operation time of LR algorithm through the parallelization using multiple threads in the GPU. Through the implemented LR-aided detector, we verify that the LR-aided detector operates a lot faster than Maximum Likelihood (ML) detector. The implemented LR-aided detector has been applied to WiMAX system to show the feasibility of its real-time processing. In addition, we demonstrate that the processing time can be reduced at the cost of 3dB SNR loss by limiting the repeating loop in Lenstra-Lenstra-Lovasz (LLL) algorithm which is frequently used in LR-aided detector.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.963-966
• /
• 2003

This paper proposes a new locking algorithm of the delay locked loop (DLL) which reduces the lock-acquisition time and eliminates false locking problem to enlarge the operating frequency range. The proposed DLL uses the modified phase frequency detector (MPFD) and the modified charge pump (MCP) to avoid the false locking problem. Adopting a new lock detector that measures delay between elects helps the fast lock-acquisition time greatly. The idea has been confirmed by HSPICE simulations in a 0.35-${\mu}{\textrm}{m}$ CMOS process.