• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.3
• /
• pp.317-324
• /
• 2007

Fluorescence measurements of dissolved organic matter(DOM) have the superior advantages over other analysis tools for applying to water quality management. A preliminary study was conducted to test the feasibility of applying synchronous fluorescence measurements for tracing and monitoring pollution sources in a small stream located in an upstream area of the Sooyoung watershed in Busan. The water quality of the small stream is affected by leachate from sawdust pile and discharge of untreated sewage. The sampling sites included an upstream site, two pipes discharging untreated sewage, leachate from sawdust, and a downstream site. Of the five field samples, the leachate was distinguished from the other samples by a high peak at a lower wavelength range and a blunt peak at 350nm, suggesting that synchronous fluorescence can be used as a discrimination tool for monitoring the pollution. The efficacy of various indices derived from the spectral features to discriminate the pollution source was tested for well-defined mixture of the sawdust leachate and the upstream stream by comparing (1)the difference between measured values and those predicted based on mass balance and the characteristics of the two samples and (2)the linear correlations between index values and mass ratios of the sample mixtures. Of various discrimination indices selected, fluorescence intensities at 276 nm$({\Delta}\lambda=30nm)$and 347 nm$({\Delta}\lambda=60nm)$ were suggested as promising potential discrimination indices for the sawdust pollution source. Despite the limited number of samples and the study area, this study illustrates the evaluation process that should be followed to develop rapid, low-cost discrimination indices to monitor pollution sources based on end member mixing analyses.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.12 no.1
• /
• pp.64-72
• /
• 2009

The method to generate a digital elevation model(DEM) from contour lines causes a problem in which the low relief landform cannot be clearly presented due to the fact that it is significantly influenced by the expression of micro landform elements according to the interval of contours. Thus, this study attempts to develop a landcover burning method that recovers the micro relief landform of the DEM, which applies buffering and map algebra methods by inputting the elevation information to the landcover. In the recovering process of the micro landform, the DEM was recovered using the buffering method and elevation information through the map algebra for the landcover element for the micro landform among the primary DEM generation, making landcover map, and landcover elements. The recovering of the micro landform was applied based on stream landforms. The recovering of landforms using the buffering method was performed for the bar, which is a polygonal element, and wetland according to the properties of concave/convex through generating contours with a uniform interval in which the elevation information applied to the recovered landform. In the case of the linear elements, such as bank, road, waterway, and tributary, the landform can be recovered by using the elevation information through applying a map algebra function. Because the polygonal elements, such as stream channel, river terrace, and artificial objects (farmlands) are determined as a flat property, these are recovered by inputting constant elevation values. The results of this study were compared and analyzed for the degree of landform expression between the original DEM and the recovered DEM. In the results of the analysis, the DEM produced by using the conventional method showed few expressions in micro landform elements. The method developed in this study well described wetland, bar, landform around rivers, farmland, bank, river terrace, and artificial objects. It can be expected that the results of this study contribute to the classification and analysis of micro landforms, plain and the ecology and environment study that requires the recovering of micro landforms around streams and rivers.

• Journal of The Korean Association For Science Education
• /
• v.38 no.3
• /
• pp.393-405
• /
• 2018

In this study, we classified the group model construction types in the actual classroom situation implementing the instructional strategy mixed with individual model construction and group model construction types. The purpose of this study is to analyze the information flow and the individual construction types of each group model construction type to obtain implications for model co-construction in a real classroom environment. A two-session class on sound propagation was carried out for thirty-three 8th grade students in Seoul. A total of 65 individual model construction and 16 group model construction processes were collected and analyzed. The group model construction types were classified as unchanged, enumerated, and elaborated. The unchanged type was found in 8 groups, the enumerated type in 3 groups, and the elaborated type in 5 groups. The isolated individual and independent construction (i.I) were found mostly in the unchanged group construction type (50.0%) and enumerated group construction type (54.5%). In the unchanged type, the radial shape of flow in which one student's information is transmitted to all the members of the group appeared. In the enumerated type, the starting point of the information flow was observed from two individuals. In the elaborated type, linear information flow appeared and both the second dissemination and reflective construction (2d.R) contributed to the group model construction (58.3%). This study suggests a viewpoint that enables to understand the process of complex model construction in an actual classroom context rather than in an ideal situation. The result of this study suggests the necessity of a modeling strategy considering the characteristics of Korean small group culture. It is expected that the discussion will progress through further studies.

• Journal of Life Science
• /
• v.26 no.5
• /
• pp.545-554
• /
• 2016

Hyaluronic acid (HA) is an important macromolecule in medical and pharmaceutical fields. HA is a natural and linear polymer composed of repeating disaccharide units of β-1, 3-N-acetyl glucosamine and β-1, 4-glucuronic acid. This work aimed to confirm the structural characteristics and anti-inflammatory activities of HA and its chemically sulfated-HA. HA was produced from a fed-batch fermentation process using Streptococcus dysgalactiae in a 5 l bioreactor. HA was isolated water-soluble form (HA-WS) and water-insoluble form (HA-WI) from culture medium, and was obtained chemically sulfated-derivative (S-HA) that resulted in a 90% yield from HA-WI. The structural features of the sulfated- HA (S-HA) were investigated by FT-IR and ¹H-NMR spectroscopy. The FT-IR and NMR patterns revealed the similarity in both the FTIR spectrum as well as NMR spectrum of both reference standard and purified HA from S. dysgalactiae. The anti-inflammatory activities of HA and S-HA were examined on LPS-induced RAW 264.7 cells. S-HA was significantly inhibited production of pro-inflammatory mediators such as nitric oxide (NO) and PGE₂ and the gene levels of iNOS and COX-2, which are responsible for the production of NO and PGE₂, respectively. Furthermore, S-HA also suppressed the overproduction of pro-inflammatory cytokine TNF-α (<80 pg/ml) and IL-6 (<100 pg/ml) compared to that of HA-WI. The present study clearly demonstrates that HA-S exhibits anti-inflammatory activities in RAW 264.7 macrophage cells.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.36 no.3
• /
• pp.75-84
• /
• 2008

The purpose of this research is to find the visual characteristics and geographic structure in a landscape of mountains in Yangsan City. In order to carry out this study, 40 view points of 6 mountains in Yangsan City were selected to experience the mountainscape. The results are as follows. The mountainscape of Yangsan City was confirmed from the view point to the object of view as ranging in middle distance reverse, the angle of elevation 11${\sim}13^{\circ}$ which give the impression of confronted to the mountain, and the horizontal angle 50${\sim}90^{\circ}$ which gives the impression of vastness. This shows that mountainscapes are perceived impressively when seeing the mountain with the meaning to feel the texture of the mountain as a confrontational relationship rather than a pictorial relationship. The geographic structure of the view point which occurs in scenes of impressive experience is classified into eight types and its characteristics are investigated. The first type is corridor, and it emerges in a long narrow linear structure made from the surrounding environment with buildings or street trees. The second is tunnel in which a vision and light hidden while passing underneath a bridge, high-level road, or inside a tunnel can be seen. Third, the maze is formed by the mountain shape. The hill spur emerges when the direction of traffic changes after turning the coner of a building or mountain edge. The hill ground emerges at the top of a hill slope. Next, parallel emerges when the observer and the mountain are in the same direction of process. Confrontation occurs when confronting an isolated mountain. Finally, the view point emerges when passing through major points such as a bridge or square and the boundary of a village or city. This research arranged visual conditions that create impressive mountainscapes. Geographic characteristics in terms of Types that make possible to experience mountainscapes were described. The results of this research will be basic data collected for the management and preservation of mountainscapes and for landscape effect evaluation. Furthermore, this research suggests theoretical evidence to preserve and manage geographic structures that create view experiences as well as to preserve the landscape in terms of view points.

• Clinical and Experimental Pediatrics
• /
• v.48 no.1
• /
• pp.75-80
• /
• 2005

Purpose : Internal tibial torsion is prevalent in East Asian countries such as Korea and Japan, where sitting on the floor is common behavior. Internal tibial torsion or excessive lateral tibial torsion may cause esthetical, functional, or psychological problems and also may induce degenerative arthritis in older age. The purpose of this study is to measure the tibial torsion in children of the Jeju area. Methods : Tibial torsion was measured in 1,042 lower extremities of 521 children from one to 12 years of age. The values of transmalleolar angles were analyzed for each age group divided by 6 months. Quadratic and linear regression models were used to fit patterns of changes in mean values of transmalleolar angles. The age at seven, which provides the highest coefficient of determination for quadratic regression analysis, was used as a cut-off point to fit different statistical models. Results : The mean transmalleolar angle was $0.10{\pm}5.79^{\circ}$ in all children,$ 0.90{\pm}5.49^{\circ}$ in males, and $-0.80{\pm}5.97^{\circ}$ in females. The value was $4.25{\pm}4.04$ in 1 year of age, gradually decreased to the lowest level of $-1.98^{\circ}$ in four years and seven months of age, increased again with age until it reached $0.67{\pm}1.10^{\circ}$ at seven years of age, and stayed at that level thereafter. Conclusion : Internal tibial torsion in infancy is known to correct spontaneously in the normal developing process. But in this study, the mean transmalleolar angle in children of Jeju area annually decreased after one year of age; to the lowest angle at four years and seven months of age; increased again gradually to the age of seven; and persisted in that level, about $10^{\circ}$ less than western children, not correcting further thereafter. These findings suggest tibial torsion might be caused by lifestyle, especially sitting on feet. To prevent abnormalities of joints and gaits, early diagnosis of tibial torsion in childhood and posture correction or early treatment when needed, seems to be necessary.

• Composites Research
• /
• v.15 no.4
• /
• pp.23-31
• /
• 2002

The two dimensional size effect of specimen gauge section ($length{\;}{\times}{\;}width$) was investigated on the compressive behavior of a T300/924 $\textrm{[}45/-45/0/90\textrm{]}_{3s}$, carbon fiber-epoxy laminate. A modified ICSTM compression test fixture was used together with an anti-buckling device to test 3mm thick specimens with a $30mm{\;}{\times}{\;}30mm,{\;}50mm{\;}{\times}{\;}50mm,{\;}70mm{\;}{\times}{\;}70mm{\;}and{\;}90mm{\;}{\times}{\;}90mm$ gauge length by width section. In all cases failure was sudden and occurred mainly within the gauge length. Post failure examination suggests that $0^{\circ}$ fiber microbuckling is the critical damage mechanism that causes final failure. This is the matrix dominated failure mode and its triggering depends very much on initial fiber waviness. It is suggested that manufacturing process and quality may play a significant role in determining the compressive strength. When the anti-buckling device was used on specimens, it was showed that the compressive strength with the device was slightly greater than that without the device due to surface friction between the specimen and the device by pretoque in bolts of the device. In the analysis result on influence of the anti-buckling device using the finite element method, it was found that the compressive strength with the anti-buckling device by loaded bolts was about 7% higher than actual compressive strength. Additionally, compressive tests on specimen with an open hole were performed. The local stress concentration arising from the hole dominates the strength of the laminate rather than the stresses in the bulk of the material. It is observed that the remote failure stress decreases with increasing hole size and specimen width but is generally well above the value one might predict from the elastic stress concentration factor. This suggests that the material is not ideally brittle and some stress relief occurs around the hole. X-ray radiography reveals that damage in the form of fiber microbuckling and delamination initiates at the edge of the hole at approximately 80% of the failure load and extends stably under increasing load before becoming unstable at a critical length of 2-3mm (depends on specimen geometry). This damage growth and failure are analysed by a linear cohesive zone model. Using the independently measured laminate parameters of unnotched compressive strength and in-plane fracture toughness the model predicts successfully the notched strength as a function of hole size and width.

• The Journal of Korean Society for Radiation Therapy
• /
• v.24 no.2
• /
• pp.77-84
• /
• 2012

Purpose: To develop a geometrical quality control real-time analysis program using an electronic portal imaging to replace film evaluation method. Materials and Methods: A geometrical quality control item was established with the Eclipse treatment planning system (Version 8.1, Varian, USA) after the Electronic Portal Imaging Device (EPID) took care of the problems occurring from the fixed substructure of the linear accelerator (CL-iX, Varian, USA). Electronic portal image (single exposure before plan) was created at the treatment room's 4DTC (Version 10.2, Varian, USA) and a beam was irradiated in accordance with each item. The gaining the entire electronic portal imaging at the Off-line review and was evaluated by a self-developed geometrical quality control real-time analysis program. As for evaluation methods, the intra-fraction error was analyzed by executing 5 times in a row under identical conditions and procedures on the same day, and in order to confirm the infer-fraction error, it was executed for 10 days under identical conditions of all procedures and was compared with the film evaluation method using an Iso-align$^{TM}$ quality control device. Measurement and analysis time was measured by sorting the time into from the device setup to data achievement and the time amount after the time until the completion of analysis and the convenience of the users and execution processes were compared. Results: The intra-fraction error values for each average 0.1, 0.2, 0.3, 0.2 mm at light-radiation field coincidence, collimator rotation axis, couch rotation axis and gantry rotation axis. By checking the infer-fraction error through 10 days of continuous quality control, the error values obtained were average 1.7, 1.4, 0.7, 1.1 mm for each item. Also, the measurement times were average 36 minutes, 15 minutes for the film evaluation method and electronic portal imaging system, and the analysis times were average 30 minutes, 22 minutes. Conclusion: When conducting a geometrical quality control using an electronic portal imaging, it was found that it is efficient as a quality control tool. It not only reduces costs through not using films, but also reduces the measurement and analysis time which enhances user convenience and can improve the execution process by leaving out film developing procedures etc. Also, images done with evaluation from the self-developed geometrical quality control real-time analysis program, data processing is capable which supports the storage of information.

• The Journal of Korean Society for Radiation Therapy
• /
• v.23 no.2
• /
• pp.91-96
• /
• 2011

Purpose: The aim of study is to expose a more uniform dose depending on the relationship between a body mass index in patients who underwent radiation therapy and an acquired dosimetric information by using a thermoluminescent dosimeter. Materials and Methods: Since 2006 to August 2011 we investigated 28 people who underwent radiation therapy were enrolled in AMC. Each patient was measured on the head, neck, chest, abdomen, pelvis, thigh, knee joint, and ankle joint using the thermoluminescent dosimeter. The measurement value of each points compared with the prescribed center point, abdominal point, and dose measurements of points on which to base the abdomen and the patient's body mass index (BMI) were compared with reference point, abdomen dose. Results: 28 patients on prescribed dose in the abdomen by which the center point, an average dose was $100.6{\pm}5.5%$, and the other seven measuring points with the average maximum difference among the head, neck, chest, pelvic, thigh, knee, and ankle were $92.8{\pm}4.2%$, $97.6{\pm}6.2%$, $96.4{\pm}5.5%$, $102.6{\pm}5.3%$, $103.4{\pm}7.9%$, $95.8{\pm}5.9%$, $96.1{\pm}5.5%$. The relationship of abdominal point dose and the patient's body mass index (BMI) was analyzed a scatter plot, and the result of linear relationship analysis by regression method, the regression of the dose (y) was -1.009 BMI (x) plus 123.3 and coefficient of determination ($R^2$) was represented 0.697. Conclusion: The total body irradiation treatment process was evaluated the dose deviation and then the prescribed dose by which the average abdominal dose was satisfied with $100.6{\pm}5.5%$. Results of the relationship analysis between BMI and dose, if we apply the correction value for each patients, it can be achieved more uniform dose delivery.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.40 no.5
• /
• pp.51-62
• /
• 2012

Geumho-dong, Seoul, a redeveloped residential area, is located in the foothills of Mt. Eungbong. The geographical undulation, the composition of a large apartment complex, and the partial implementation of the redevelopment project have caused the severe physical and social disconnections in this area. In order to recover functioning in the disconnected community, this study pays attention to the regeneration of the open spaces as an everyday place and in the form a network system among those open spaces. Various types of the open spaces are classified into points or faces, 'bases' and linear 'paths' analyze the network status. More than half of the open space have connecting-distance of 500m or more. Furthermore, many areas are not even included in the service-area of the open spaces. Analysis of the connectivity and integration value using the axial map has carried out to check weak linkages and to choose the sections where additional bases are required. In addition, to improve the quality of the bases and the paths, a field investigation is conducted and problems are diagnosed. The network planning of the open spaces in Geumho-dong is established, ensuring the quality and quantity of bases and paths. The plan includes the construction of an additional major base in the central area and six secondary bases in other parts, and comes up with ways to improve the environment of underdeveloped secondary bases. In the neighborhood parks at Mt. Daehyun areas, the major path are added, and the environment of the paths is improved in certain areas. Because of the network planning, the connecting-distances between bases are reduced significantly, the connectivity and integration value of the area are increased, and the service areas of the open spaces cover the whole area properly. Although this study has some limitations such as the needs for the legal and institutional supports and difficulties of a quantitative indexing process, its significance lies in the suggestion of a more reasonable and practical plan for the overall network system by defining complex types of open spaces simply and clearly and by examining the organic relationships quantitatively and qualitatively.