• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.12
• /
• pp.104-109
• /
• 1996

A current-controlling transadmittance amplifier is proposed. It consists of a linear transadmittor and a current gain cell followed by three current mirrors. The proposed transadmittance amplifier is used to design a current-controlling frequency-dependent negative resistor (FDNR). Experimental results are presented to verify theoretical predictions. The results show close agreement between predicted behaviour and experimental performance.

• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.215-220
• /
• 1999

In fabricated linear power amplifier(LPA), the third-order inter-modulation distortion(IMD) for main amplifier alone is 10.61dBc, and the IMD for LPA with predistorter and feedforward loop combined is 32.50dBc. Therefore, the IMD characteristic results an improvement of approximately 22dB. The main amplifier efficiency with single tone input is close to 30%, and the efficiency of the overall LPA with predistorter is 27.4% and predicted feedforward loop efficiency without predistorter is about 20%. Therefore, LPA with predistorter and feedforward loop combined is improved by 7.4%.

• Journal of IKEEE
• /
• v.4 no.2 s.7
• /
• pp.241-248
• /
• 2000

A linear power amplifier is particular emphasized on the CDMA system using a linear modulation scheme, because intermodulation distortion which cause adjacent channel interference and co channel interference is mostly generated in a nonlinear power amplifier. In this paper, a new type of linearization technique proposed. It is presented that balanced MESFET predistortion linearizer added. Experimental result are present for Korea PCS(Personal Communication Service) frequency band. The implemented linearizer is applied to a 30dBm class A power amplifier for simulation Performance. The predistortion linearizer improves the 1dB compression point of the HPA about 2dBm, and intermoudulation distortion about 12.5dBc.

• Journal of Advanced Navigation Technology
• /
• v.3 no.1
• /
• pp.52-59
• /
• 1999

Digital microwave wideband receiver including linear amplifier, analog-to-digital converter(ADC) and digital signal processor is able to analyze its performance using sensitivity and dynamic range of system. Determination of gain, third-order intermodulation products and ADC characteristics and design criteria for the linear amplifier chain is essential problem for sensitive and dynamic range. Also, if there are two signals with frequencies very close, digital signal processor must be able to separate the two signals. In this paper, we measured dynamic range as gain was changed and determined gain value for the proper sensitivity and dynamic range and high resolution spectrum estimation was used to separate two close signals.

• ETRI Journal
• /
• v.19 no.2
• /
• pp.35-47
• /
• 1997

A power amplifier operating at 3.3 V has been developed for CDMA/AMPS dual-mode cellular phones. It consists of linear GaAs power MESFET's, a new gate bias control circuit, and an output matching circuit which prevents the drain terminal of the second MESF from generating the harmonics. The relationship between the intermodulation distortion and the spectral regrowth of the power amplifier has been investigated with gate bias by using the two-tone test method and the adjacent channel leakage power ratio (ACPR) method of CDMA signals. The dissipation power of the power amplifier with a gate bias control circuit is minimized to below 1000 mW in the range of the low power levels while satisfying the ACPR of less than -26 dBc for CDMA mode. The ACPR of the power amplifier is measured to be -33 dBc at a high output power of 26 dBm.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.4
• /
• pp.385-391
• /
• 2007

A class D digital audio amplifier with small size, low cost, and high quality is positively necessary in the multimedia era. Since the digital audio amplifier is based on the PWM signal processing, it is improper to analyze the principle of signal generation using linear system theories. In this paper, a class D digital audio amplifier based ADSM (Advanced Delta-Sigma Modulation) is considered. We first model the digital audio amplifier and then explain the operation principle using variable structure control algorithm. Moreover, the ripple signal generated by the hysteresis in the comparator has a significant effect on the system performance. Thus, we present a method to find the magnitude and the frequency of the ripple signal using describing function. Finally, simulations and experiments are provided to show the validity of the proposed methods.

• ETRI Journal
• /
• v.32 no.1
• /
• pp.151-153
• /
• 2010

A highly efficient linear and compactly integrated series-type Doherty power amplifier (PA) has been developed for wideband code-division multiple access handset applications. To overcome the size limit of a typical Doherty amplifier, all circuit elements, such as matching circuits and impedance transformers, are fully integrated into a single monolithic microwave integrated circuit (MMIC). The implemented PA shows a very low idle current of 25 mA and an excellent power-added efficiency of 25.1% at an output power of 19 dBm by using an extended Doherty concept. Accordingly, its average current consumption was reduced by 51% and 41% in urban and suburban environments, respectively, when compared with a class-AB PA. By adding a simple predistorter to the PA, the PA showed an adjacent channel leakage ratio better than -42 dBc over the whole output power range.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.3A
• /
• pp.356-359
• /
• 2006

A monolithic SiGe HBT variable gain driver amplifier(VGDA) with high dB-linear gain control and high linearity has been developed as a driver amplifier with ground-shielded microstrip lines for 5-GHz transmitters. The VGDA consists of three blocks such as the cascode gain-control stage, fixed-gain output stage, and voltage control block. The circuit elements were optimized by using the Agilent Technologies' ADSs. The VGDA was implemented in STMicroelectronics' 0.35${\mu}m$ Si-BiCMOS process. The VGDA exhibits a dynamic gain control range of 34 dB with the control voltage range from 0 to 2.3 V in 5.15-5.35 GHz band. At 5.15 GHz, maximum gain and attenuation are 10.5 dB and -23.6 dB, respectively. The amplifier also produces a 1-dB gain-compression output power of -3 dBm and output third-order intercept point of 7.5 dBm. Input/output voltage standing wave ratios of the VGDA keep low and constant despite change in the gain-control voltage.

• Journal of the Korea Society of Computer and Information
• /
• v.6 no.4
• /
• pp.125-130
• /
• 2001

The application of the operational trasconductance amplifier (OTA) in the design of a amplifier with voltage-controlled gam is demonstrated first. I designed OTA with linear operation and constructed a Amplifier with two OTA. In this design. I used OTA as open loop. Computer simulation result, designed OTA and Amplifier charateristics has a good matching with the theoritical value. The OTA is used often in open-loop and therefore it is wise to learn how to treat the two input pins independently, as a vertual short circuit can not be assured in many configurations.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.10A
• /
• pp.1072-1077
• /
• 2007

In this paper, a power amplifier intermodulation distortion has been analyzed to improve linearity and the analysis results are used to minimize the distortion for linear power amplifier design. The proposed design technique is which the intermodulation distortions of the final amplifier are removed by driver intermodulation distortions. This proposed technique is based on AM to AM distortion analysis using power series, and AM to PM distortion analysis results using Bessel function. To verify this technique implement a cellular HPA(High Power Amplifier) 30W. From the results of the implementation and measurement for the linear power amplifier, the spurious characteristic is shown as 50 dBc at 1.98 MHz with 30 W with 20FA. These results show that distortion characteristics are improved as much as 10 dB in spurious characteristic compared with conventional design method.