• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.77-84
• /
• 2001

Measurements of local CO, $CO_2$, $O_2$, $N_2$, $C_3$H$_{8}$, NOx concentrations and flame temperature are made for partially premixed flame with and without acoustic excitation. The CO, $CO_2$, $O_2$, $N_2$, and $C$_3$H_8$ concentrations are determined by thermal conductivity detection (Gas-chromatograph) and NOx concentrations are determined by chemiluminescent detection (NOx analyser). To measure local sample concentration, sampling probe was made by quartz with inlet diameter of 0.25mm. In the case of excitation, the visual shape of the flame is changed from laminar flame to turbulent-like flame. The flame length is also reduced, and the flame width becomes broad. In the observation of emission concentration without acoustic excitation, meanwhile, the $CO_2$ and NOx concentrations peak at flame front where the mixture meets with surrounding air, and the CO concentration is increasing at maximum position of CO2 concentration and peaks at the centerline of the burner. In the case of acoustic excitation, the $CO_2$ concentration is widely occurred at nozzle of the burner and is higher relative to unexcitation. The CO concentration is much reduced, but NOx concentration is more increasing. And flame temperature is higher relative to unexcitation. These are caused by enhancing of mixing with surrounding air due to excitation. However, in the case of acoustic excitation, the total NOx concentration is reduced because of the shortened flame length which affects residence time.e.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.133-140
• /
• 2007

The purpose of this study was to evaluate the effects of gasoline fuel to the LPI engine. Firing test bench was used in order to assess the effect on gasoline-injected LPI engine. Gasoline fuel was supplied into the reverse direction(3-4-2-1 cylinder) at 3.0 bar with commercial gasoline fuel pump. Engine test was performed using the firing test mode at end of line. The deviations of excess air ratio of each cylinder and maximum combustion pressure using gasoline fuel were within 0.1 and $1{\sim}2\;bar$. Engine start time was measured with changing coolant temperature at $20^{\circ}C,\;40^{\circ}C,\;80^{\circ}C$, respectively. Residual gasoline volume in the fuel line was measured about 32 cc after firing test and it was less than 2 cc within 10 seconds purging. To simulate the end of line, the residual gasoline in the fuel line was purged during 5 and 10 seconds. Start time of LPI engine with LPG fuel were 0.61 and 0.58 seconds. This work showed that severe problems such as misfiring and liner scuffing were not occurred applying gasoline fuel to LPI engine.

• Environmental and Resource Economics Review
• /
• v.29 no.4
• /
• pp.443-468
• /
• 2020

Broad effects of fuel-transition in all type of ground transportation have occurred with the help of the advances in electric vehicle (EV) technologies and the increases in EV supply. This research estimates the economic benefit of air environmental improvements, which results from the fuel-transition of high-mileage business cars(taxies) in metropolis. If we consider power production sector for EV operation, some air pollutants will be produced. In this respect, this research takes both the mixture of power sources in power production level and the driving pattern of business cars into account when investigating the economic benefit in air environment resulted from the fuel-transition of business cars(taxies). According to our results, the business cars' fuel transition from LPG to electricity brings about 21.5￦/km (8.6million won/year) of economic benefit in air environment. These results emphasize the necessity and appropriateness of public polices for expanding power production with renewable energies and facilitating EV distribution.

• Journal of the Korean Institute of Gas
• /
• v.10 no.4 s.33
• /
• pp.63-69
• /
• 2006

With the increased interest in reducing air pollution, supply of natural gas for gas vehicles is increasing. Thus, the number of establishments of LNG and CNG stations is increasing as well. However, due to major gas accidents such as the fire and explosion accident of a Bucheon LPG station in 1998, it is difficult to establish a new station. In this research, we conducted qualitative hazard analysis fer LCNG/LNG multi-station by using the K-PSR method and proposed recommendations for hazard mitigation.

• Journal of Hydrogen and New Energy
• /
• v.28 no.6
• /
• pp.642-648
• /
• 2017

The use of fossil is causing enviromental all over the world. So hydrogen energy is attracting attention as one of the alternative. The government announced that 30% of the air pollution is because of the Internal Combustion Engine Vehicle. In addition, they plans to reduce Internal Combustion Engine Vehicles by 2030 and increase (electric vehicles, EV) or (fuel cell vehicle, FCV). The FCV is evaluated as a next-generation green car because it has a long driving distance and short charging time. However, the hydrogen industry is not able to expand due to the lack of refueling infrastrucutre. This paper predicts the site of hydrogen refueling stations for the expansion of the hydrogen industry and proposes a method to supply hydrogen multi energy filling stations.

• Journal of the Korean Institute of Gas
• /
• v.14 no.4
• /
• pp.56-62
• /
• 2010

The purpose of this paper analyzes and investigates the failure case studies of electronic control sensors for a LP gas engine. The malfunction of crank angle sensor, which controls a fuel injection volume of LP gas, displays an irregular and non-uniform pulse wave form. The pulse form, which is related to the noise of the crank angle sensor, displays at the rectangular peak with a saw-toothed shape and is intermittently generated with a level of 2.46V noise signal. The malfunction of No. 1 TDC sensor in which is caused from the internal disorder affects to the reduction of engine power and engine stop suddenly. If the malfunction of oxygen sensor is occurred due to a wiring problem of a sensor connector, the LP gas vehicle may produce a shaking and disharmony of an engine because of no signal supply from the oxygen sensor. The air cleaner replica produces the clogging of continuous supply of fresh air. This may cause the retardation of vehicle acceleration and engine disharmony intermittently.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.144-151
• /
• 2016

This study effect of engine oils on regulated fuel economy and emissions including particulate matter (PM) to provide basic data for management of engine oil in vehicles. Three engine oils (Group III base oil, Group III genuine oil with additive package and synthetic oil with poly alpha olefins (PAOs)) were used in one gasoline, one LPG(liquefied petroleum gas) and two diesel vehicles. In the case of diesel vehicles, one is a diesel vehicle without DPF (diesel particulate filter) other is a diesel vehicle with DPF. In this study, the US EPA emission test cycle FTP-75, representing city driving, was used. HORIBA, PIERBURG, and AVL gas analyzers were used to measure the fuel economy and regulated emissions such as CO, NOx, and THC. The number of PM was measured using a PPS (pegasor particle sensor). And, the shape of PMs was analyzed by SEM (scanning electron microscope). The effects of oil type on fuel economy, exhaust gas, and PM were not significant because engine oil consumption by evaporation and combustion in the cylinder is very tiny. Fuel and vehicle type were dominant factors in fuel economy and emissions. HC emission from gasoline vehicles was higher than that from other vehicles and NOx emission from diesel vehicles was higher than that from other vehicles. The number of PM was not affected by the engine oil, but by the driving pattern and fuel. The shapes of the PM, sampled from each vehicle using any test engine oil, were similar.

• Journal of the Korean Institute of Gas
• /
• v.17 no.3
• /
• pp.8-13
• /
• 2013

The purpose of this paper is to study for fire example by fuel leakage in LPG Vehicle. At first example, the car was repaired the fuel line that was connected with pressure hose between fuel regulator and injector in engine. But the service man was not very tighten with regular torque. At a result, the gas leaked on hot parts of engine. It verified the production of fire by engine heat. At second example, when the repair man, after replacement the injector, inserted the injector in a assembling part of it, he didn't the transform condition of fixing part. Therefore, the tearing phenomenon of O ring producted the controlled leakage of fuel by the injector deflection. It found the fact that the fuel leaked with gap of O ring. At third example. the fuel-cut solenoid valve was lined with pressure regulator unit. But the service man didn't throughly certify the leaked work of connected parts after repaired it. As a result, it certified the fire by engine heating leaked liquefied petroleum gas. Therefore it have to minimize the fire production that the driver should do no problem to throughly manage the fuel system.

• 월간 기계설비
• /
• s.305
• /
• pp.78-86
• /
• 2015

프로필렌은 에틸렌과 함께 자동차부품, 수지, 섬유 등 석유화학 제품의 기초 원료로 사용되는 불포화 탄화수소 화합물의 일종이며 보통 석유 정제과정의 부산물로 생산된다. 그러나 최근들어 급증하는 프로필렌 수요 충족을 위해 프로판을 원료로 하는 프로필렌 생산기술(PDH)이 크게 주목받고 있다. 이에 따라 프로필렌 전용 생산공장으로는 세계 최대 규모인 SK어드밴스드 PDH(Propane Dehydroganation) Plant가 울산시 남구 신항만 근처 약 10만$4,000m^2$ 부지에 건설되고 있다. 울산 PDH 현장은 지난 2014년 6월 1일 시공에 들어가 오는 2016년 3월 31일 완공될 예정이다. 완공 후 정상가동에 들어가면 70만t의 LPG를 원료로 연간 약 60만t의 프로필렌을 생산하게 된다. 본지는 기계적 완성(MC, Mechanical Completion)을 달성하고 테스트 작업이 한창인 울산 PDH Plant 현장에서 P1 Area의 기계설비, 배관 및 철골공사를 담당하고 있는 (주)동부(대표 김재홍)의 변유진 현장소장을 만났다.

• Journal of Powder Materials
• /
• v.6 no.2
• /
• pp.163-170
• /
• 1999

Engine valve seat is a functionally important part for maintaining engine performance. The progress of automotive technology has increased the severity of conditions to which it is exposed, especially as regards LPG fuel engines and turbocharger. Therefore, it requires excellent heat and wear resistance to meet the severe condition inside the engine. In the present study, effects of solid lubricants such as CaF$_2$, MnS and MoS$_2$ on microstructure and mechanical properties of sintered Fe alloys for valve srats have been investigated for the development of valve seat material with high temerature wear resistance. As a results of engine simulation test, 0.5 wt% CaF$_2$ specimen showed the most excellent property, but in the overall aspect of view valve recession has increased with increasing the amount of solid lubricants.