• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1725-1734
• /
• 2016

This paper presents a novel seven-level (7L) voltage source converter for high-power medium-voltage applications. The proposed topology is an H-bridge connection of two nested neutral-point clamped (NNPC) converters and is referred to as an HNNPC converter. This converter exhibits advantageous features, such as operating over a wide range of output voltages, particularly for 10-15 kV applications, without the need to connect power semiconductors in series; high-quality output voltage; and fewer components relative to other classic seven-level topologies. A novel sinusoidal pulse width modulation technique is also developed for the proposed 7L-HNNPC converter to control flying capacitor voltages. One of the main features of the control strategy is the independent application of control to each arm of the converter to significantly reduce the complexity of the controller. The performance of the proposed converter is studied under different operating conditions via MATLAB/Simulink simulation, and its feasibility is evaluated experimentally on a scaled-down prototype converter.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.793-797
• /
• 2003

Switching PFC converters are widely used not only to comply the power quality specification but also for maximum efficiency. However switching PFC converters generate serious electromagnetic interference (EMI). In this paper to solve this problem, we applied the APW(Anti Phase Winding) and RPWM(Ran-dom PWM) technique to PFC boost converter and obtained satisfactory results. Simulation and experimental results show the improved harmonic and reduced EMI effect in air-conditioner system.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.559-561
• /
• 1994

In this paper a new AC/DC/AC converter in which Soft-Switched-Inductor Module is used, is proposed. This new converter adopts ZVS(Zero-Voltage-Switching) for main switches. Therefore the switching loss is minimized and high frequency operation is possible. Operations principles, short analyses and computer simulation results are presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.10
• /
• pp.1169-1176
• /
• 2010

The RF front-end for L1/L2 dual-band Global Positioning System(GPS) receiver is presented in this paper. The RF front-end(down-converter) using low IF architecture consists of a wideband low noise amplifier(LNA), a current mode logic(CML) frequency divider and a I/Q down-conversion mixer with a poly-phase filter for image rejection. The current bleeding technique is used in the LNA and mixer to obtain the high gain and solve the head-room problem. The common drain feedback is adopted for low noise amplifier to achieve the wideband input matching without inductors. The fabricated RF front-end using $0.18{\mu}m$ CMOS process shows a gain of 38 dB for L1 and 41 dB for L2 band. The measured IIP3 is -29 dBm in L1 band and -33 dBm in L2 band, The input return loss is less than -10 dB from 50 MHz to 3 GHz. The measured noise figure(NF) is 3.81 dB for L1 band and 3.71 dB for L2 band. The image rejection ratio is 36.5 dB. The chip size of RF front end is $1.2{\times}1.35mm^2$.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.564-567
• /
• 1991

In this paper a predictive current control strategy is adopted in the D.C motor drive using dual converter. It is a kind of feedforward control working without overshoot within very short settling time. The difference to the well-known PI current control lies in considering the computer's ability of pre-calcurating the converter's behavior. By simulation it is shown that the predictive current control solve the problems of optimal PI current control, such as overshoot and settling time.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.11
• /
• pp.167-174
• /
• 1996

For the decreasing of switching loss, this paper designs the improved buck converter circuit and then compare with the conventional buck converter and finally analyzes the performance. When the switch is turn-off, in the buck converter using the smoothing capacitor, the flow of transient current and peak voltage having the high frequency components was generated because of the instantaneous open-state in the teminals of the switch. However, the buck converter presented in this paper eliminated this disadvantage by using the L-C circuit. Therefore, the higher PF in 0.85 is achieved than that of the buck converter using the smoothing capacitor. Also, due to the decreasing of the harmonic contain rate, the current usage rate is to be higher than that of the conventional buck converter by 4.48dB and the output voltage varient rate for the step response is to be lower 1.32 times than that of the conventional buck converter.

• Journal of IKEEE
• /
• v.19 no.3
• /
• pp.335-341
• /
• 2015

Recently a demand for high precision absolute position transducer is increasing in order to control thickness in steel industry. LVDT (linear variable differential transformer) is widely used to measure the absolute position in the linearly moving cylinder under poor factory environment. In this paper we implement the three phase LVDT with a high resolution of one micron and L/D (LVDT to digital) converter. First we designed U, V, and W three phase signaling using FPGA. Second a pulse output algorithm is designed for position information with A and B phase waveforms. Finally the performance is compared with previous sensors. Experiments show that the linearity deviation error is 0.009788 [mm] and the average sinusoidal THD is 0.0751%, which means 2.2% and 33% more improved result than the previous sensors respectively.

• Journal of Satellite, Information and Communications
• /
• v.2 no.2
• /
• pp.64-68
• /
• 2007

This paper describes the development of RF front.end equipment of a wide band high precision satellite navigation receiver to be able to receive the currently available GPS navigation signal and the GALILEO navigation signal to be developed in Europe in the near future. The wide band satellite navigation receiver with high precision performance is composed of L - band antenna, RF/IF converters for multi - band navigation signals, and high performance baseband processor. The L - band satellite navigation antenna is able to be received the signals in the range from 1.1 GHz to 1.6 GHz and from the navigation satellite positioned near the horizon. The navigation signal of GALILEO navigation satellite consists of L1, E5, and E6 band with signal bandwidth more than 20 MHz which is wider than GPS signal. Due to the wide band navigation signal, the IF frequency and signal processing speed should be increased. The RF/IF converter has been designed with the single stage downconversion structure, and the IF frequency of 140 MHz has been derived from considering the maximum signal bandwidth and the sampling frequency of 112 MHz to be used in ADC circuit. The final output of RF/IF converter is a digital IF signal which is generated from signal processing of the AD converter from the IF signal. The developed RF front - end has the C/N0 performance over 40dB - Hz for the - 130dBm input signal power and includes the automatic gain control circuits to provide the dynamic range over 40dB.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.1989-1992
• /
• 1997

A new soft switching single stage AC-DC full bridge boost converter with unit input power factor and isolated output is presented. Due to using of the non-dissipative snubber in the primary side, a single stage high-power factor isolated full bridge boost converter has a significant reduction of switching losses in main switching devices and output rectifiers of the primary and secondary side, respectively. The non-dissipative snubber adopted in this study is consisted of a snubber capacitor C. and a snubber inductor $L_r$, a fast recovery snubber diode $D_r$, a commutation diode $D_p$. This paper presents the complete operating principles, theoretical analysis and simulation results.

• Journal of the Korean Society of Tobacco Science
• /
• v.27 no.1 s.53
• /
• pp.11-18
• /
• 2005

The nicotine converter genotypes of burley tobacco (Nicotiana tabacum L.), which convert nicotine to nornicotine, contain a high amount of nornicotine that degrades tobacco quality and smoking taste. Elimination of nicotine converter plants before seed harvesting is required for breeding nicotine low-converter lines and for increasing their seed production. This study aims to develop a rapid and convenient method of identifying nicotine converter plants of burley breeding lines of KB9118(KB108) using thin-layer chromatography (TLC) and isatin coloration method. Out of 223 plants in 10 lines harvested at maturity in 2002, 102 plants ($45\%$) were identified as nicotine converters by TLC of tobacco leaves air-cured. For 16 lines selected as low-converters in 2002, 148 plants grown in the field in 2003 were tested by the isatin coloration method using two detached leaves at the flowering stage thoroughly sprayed with $1\%\;NaHCO_3$ solution and cured in conditioned chambers for the early identification of nicotine to nornicotine conversion. From these samples, 46 plants ($31\%$) in 4 lines were identified as nicotine converters, indicating that the ratio of converters significantly decreased by one time selection. Mean percent conversion of non-screened lines was $14\%$ higher than that of following generation. Therefore in the burley tobacco, a rapid and convenient means of identifying and removing nornicotine converter plants by the isatin coloration method during growth in the greenhouse or field were effective in reducing the converter plants in the following generation.