• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.4
• /
• pp.39-44
• /
• 2010

To increase the fracture toughness of paper made of Sw-BKP, refining and kneading conditions were analyzed. Curl and kink was known to increase the strain at break and the fracture touhness. Sequence of multiple stage beating, beating load and kneading were compared. When we applied a kneading treatment using a kneader at the final step, the most of the fiber transformation such as curl and kink occurred, the more the bulk and air-permeability improved. Physical strength and TEA(tensile energy absorption) were increased higher when kneading treatment before refining than only refining treatment was performed. TEA was increased because of higher elongation. It was found that the highest fracture toughness was obtained when applying the kneading treatment to the fibers in the pre-treatment step rather than in the middle step of beating or in the final step of beating.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.3
• /
• pp.47-54
• /
• 2015

In this study, effects of kneading treatment on the properties of hardwood bleached kraft pulp (HwBKP), softwood bleached kraft pulp (SwBKP) and hardwood bleached chemi-thermo-mechanical pulp (HwBCTMP) were elucidated with a laboratory two-shaft kneader. Kneading treatment was performed at 30% (w/w) of pulp concentration and the number of passes through the kneader was adjusted from 0 to 10 passes. Then, changes in properties of pulp fibers were evaluated. It was found that fiber characteristics were influenced by kneading treatment. Fiber length was decreased with kneading while other morphological properties such as fiber width, curl and kink became increased as the number of passes through the kneader increased from 0 to 5 passes. The magnitude of changes in the morphological properties of softwood chemical pulp was the largest, followed by hardwood chemical pulp. The morphological properties of HwBCTMP were little influenced by kneading treatment. Swelling of fiber measured by WRV was increased with kneading except of HwBCTMP.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.1-10
• /
• 2002

Flow computations around forward sweep wing small aircraft have been conducted in this study. The main-wing of the forward-wing small aircraft is composed of two planforms: the inboard wing section with backward sweep angle which is known as strake and the outboard wing section with forward sweep angle. The geometrical discontinuity or kink generated by the combination of these two different planforms requires detailed flow analysis around wing. Four different solvers were used to calculate aerodynamic data and the accuracy of each method is examined. For the convenience of grid generation over the aircraft geometry, the overset grid method was applied. Through this calculation, the basic aerodynamic data of the forward-wing aircraft were provided and the aerodynamic characteristics of the wing is expounded.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.7
• /
• pp.69-74
• /
• 2003

By employing vane tip concept, a new rotor blade (NRSB-I) has been designed to enhance the noise characteristics of BERP blade. Numerical analyses have been performed for hovering rotor and the results are compared with respect to those of original BERP blade. Although the thrust of designed rotor decreases by 6-7% due to cutout at the tip region, the results indicate that the actual performance loss is negligible because power reduction is greater than thrust loss. It is also found that aerodynamic fence is required at the outboard kink to obtain clearly separated twin-vortices because the vortex generated at kink is diffused during the convection over the blade surface.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.145-145
• /
• 2010

반도체 소자의 크기가 수십 나노미터 영역으로 줄어들면서, 메모리 소자 또한 미세화를 위해 새로운 기술을 요구하고 있다. 1T DRAM은 하나의 트랜지스터와 하나의 캐패시터 구조를 가진 기존의 DRAM과 달리, 캐패시터 영역을 없애고 하나의 트랜지스터만으로 동작하기 때문에 복잡한 공정과정을 줄일 수 있으며 소자집적화에도 용이하다. 또한 SOI (Silicon-On-Insulator) 기판을 사용함으로써 단채널효과와 누설전류를 감소시키고, 소비전력이 적다는 이점을 가지고 있다. 1T DRAM은 floating body effect에 의해 상부실리콘의 중성영역에 축적된 정공을 이용하여 정보를 저장하게 된다. floating body effect를 발생시키기 위해 본 연구에서는 SOI 기판을 사용한 MOSFET을 사용하였는데, SOI 기판은 불순물 도핑농도에 따라 상부실리콘의 공핍층 두께가 결정된다. 실제로 불순물을 $10^{15}cm^{-3}$ 정도 도핑을 하게 되면 완전공핍된 SOI 구조가 된다. 이는 subthreshold swing값이 작고 저전압, 저전력용 회로에 적합한 특성을 보이기 때문에 부분공핍된 SOI 구조보다 우수한 특성을 가진다. 하지만, 상부실리콘의 중성영역이 완전히 공핍되어 정공이 축적될 공간이 존재하지 않게 된다. 이를 해결하기 위해 기판에 전압을 인가 후 kink effect를 확인하여, 메모리 소자로서의 구동 가능성을 알아보았다. 본 연구에서는 상부실리콘의 두께가 감소함에 따라 1T DRAM의 메모리 특성변화를 관찰하고자, TMAH (Tetramethy Ammonuim Hydroxide) 용액을 이용한 습식식각을 통해 상부실리콘의 두께가 각기 다른 소자를 제작하였다. 제작된 소자는 66 mv/dec의 우수한 subthreshold swing 값을 나타내며 빠른 스위칭 특성을 보였다. 또한 kink effect가 발생하는 최적의 조건을 찾고, 상부실리콘의 두께가 메모리 소자의 쓰기/소거 동작의 경향성에 미치는 영향을 평가하였다.

• The Journal of the Petrological Society of Korea
• /
• v.24 no.2
• /
• pp.125-139
• /
• 2015

Rock structural and microstructural analyses on the deformed Cheongsan granite, which is characterized by abundant feldspar megacrystals, have been carried out to understand the microstructural change during the mylonitization by ductile shear deformation. In K-feldspars, the characteristic microstructures are recognized as microkinks, microfractures, myrmekites, flame perthites, and core-and-mantle structures without the development of subgrains in outer core-zone. Microkinks are observed in both the microfractured and unmicrofractured K-feldspars and the directions of their axes are generally extended across the adjacent K-feldspar fragments bounded by microfractures. Myrmekites and flame perthites are found on the strain-localized boundaries of the microfractured K-feldspars. In plagiclases, microfractures, deformation twins and kink bands are predominant. Grain size reduction of plagioclase megacrysts also occurs by microfracturing but the core-and-mantle structures like the case of K-feldspars are uncommon in the microfractured plagioclases. The deformation twins, which overlap the igneous zoning structures, are often found in less deformed rocks. The twin lamellae in more deformed rocks generally bisect the obtuse angles of conjugate kink-band boundaries, and are microfractured or microfaulted and randomly oriented. From such characteristic microstructures, thus, it can be suggested that the micostructures during the mylonitzation of Cheongsan granite was developed as follows: production of microkinks in the K-feldspar megacrysts and of deformation twins and kink bands in the plagioclase megacrysts, and then grain-size reduction of the feldspar megacrysts through microfracturing, and then production of core-and-mantle structures (grain-size reduction of the microfractured K-feldspars through grain boundary migration), myrmekites and flame perthites in the microfractured K-feldspars.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.322-325
• /
• 2000

N-channel poly-Si TFT, Processed by Solid Phase Crystalline(SPC) on a glass substrate, has been investigated by measuring its electrical properties before and after electrical stressing. It is observed that the threshold voltage shift due to electrical stress varies with various stress conditions. Threshold voltages measured in 1.5$\mu\textrm{m}$ and 3$\mu\textrm{m}$ poly-Si TFTs are 3.3V, 3.V respectively. With the threshold voltage shia the degradation of transconductance(G$\_$m/) and subthreshold swing(S) is also observed.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.297-299
• /
• 2002

To wind a HTS (High Temperature Superconductor) tape conductor on a bobbin, double pancake winding technique is widely used to reduce number of splicing contacts between conductor pieces. However, this makes some Ic (critical current) degradation on kink points which is unavoidable. This paper describes the two ways of winding; usual double pancake and soldered double pancake. Characteristics of the two windings are measured and compared.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.479-480
• /
• 2011

관로내 케이블 포설시 케이블 허용장력이 포설장력을 초과하지 않도록 주의해야 한다. 또한, 케이블 포설 도중 Kink가 발생하지 않도록 케이블 드럼을 반드시 세워서 포설해야 하고, 케이블 드럼을 눕혀서 포설해서는 안 된다. 또한, 허용전류를 고려하여 케이블 상호간의 간격을 일정하게 유지해야 한다. 관로 내 케이블을 설치할 경우 직선구간 뿐 아니라 굴곡구간에도 설치되므로 포설측압이 허용측압을 초과하지 않도록 시설해야 한다. 측압에 견디기 위해서는 케이블 포설시 곡률 반경을 케이블 외경의 10배 이상으로 유지하는 것이 중요하다.

• Journal of the Korean Vacuum Society
• /
• v.3 no.1
• /
• pp.17-25
• /
• 1994

장전자 방출법을 이용하여 Kink 또는 loosely closed pack의 텅스텐 결정면(310) (221) (211) 의 수소흡착에 대한 일함수의 변화를 측정하고 상대 흡착율을 주입량과 일함수의 변화로 결정할 수 있는 방법을 제시 하였다. 또한 (310)면과 (221)면에 대한 수소의 heat of desorption을 측정하였으며 초고진 공 장치내에서 팔라듐의 수소 source로서의 가능성을 확인하였다.