• Journal of applied mathematics & informatics
• /
• v.29 no.5_6
• /
• pp.1463-1475
• /
• 2011

This paper proposes a new generalized iterative method (SSOR-like method) for solving augmented system. A functional equation relating two involved parameters is obtained, and some convergence conditions for this method are derived. This paper generalizes some foregone results. Numerical examples show that, this method is efficient by suitable choices of the involved parameters.

• Journal of Broadcast Engineering
• /
• v.14 no.5
• /
• pp.650-653
• /
• 2009

Turbo-coded CDMA system is analyzed and simulated in an indoor wireless infrared channel. The indoor infrared channel is modeled as a non-directed diffuse link. From the simulation results, it is confirmed that the turbo coding is very effective in improving BER (bit error rate) performance, and outperforms BCH code.

• Structural Engineering and Mechanics
• /
• v.6 no.5
• /
• pp.517-527
• /
• 1998

This paper describes an exact method of analysis for natural vibration of diagonal networks by considering an equivalent cyclic periodic structure and adopting the double U-transformation technique. Both a lumped mass system and a distributed mass system are considered to investigate the diagonal networks. The exact solution for the frequency equations and the natural modes of the networks can be derived. As numerical examples, square diagonal cable networks with different meshes are worked out.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.510-513
• /
• 1988

This paper describes an effective trunk loop signal processing method and analyzes execution time of program in the DTCP(Digital Trunk Circuit Processor) in the TDX-1A digital switching system. To predict a maximum trunk capacity, also analyzes to Z80A system clock(4Mbit/s, 2.5Mbit/s) and scanning period(8mS,5mS) respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.911-914
• /
• 2007

We developed the laser annealing system using green laser of 261W(5kHz) and 75.5mJ/pulse(2kHz). We confirmed that this system makes it possible to form two kinds(large or uniformed grain) of poly-Si by changing its polarized directions. By using ${\mu}-crystal-Si$ as irradiated films, grain size uniformity is better than that using a-Si.

• Korean Journal of Environmental Agriculture
• /
• v.11 no.3
• /
• pp.225-234
• /
• 1992

Thermal decomposition was conducted to investigate the influence of the various factors on stability of a new insecticide, [O, O-Diethyl O-(1-phenyl-3-trifluoromethyl-5-pyrazoyl) thiophosphoric acid ester : KH-502], in view of those informations applicable for industrial exploitation. In the thermal decomposition experiment, KH-502 was, after mixing with Fe, Cu and adjustment of moisture and pH conditions, subjected to three temperatures, 25, 50, and $100^{\circ}C$. Results for stability, and degradation pattern of KH-502 from the above experiment can be summarized as follows: 1. Main products of the thermal decomposition when this was conducted in the closed system were identified as following five compounds:O, O, O-Triethylthiophosphoric acid(TEPA), 1-Phenyl-3-trifluoromethyl-5-ethoxypyrazole(PTMEP), 1-Phenyl-2-ethyl-3-trifluoromethyl-5-hydroxypyrazole(PETMHP), O, O-Diethyl O-(1-phenyl-3-trifluoromethyl-5-pyrazoyl)phosphoric acid ester(KH-502 oxo form), O, S-Diethyl O-(1-phenyl-3-trifluoromethyl-5-pyrazoyl)phospho rothiolate(S-ethyl KH-502). However, compounds such as oxo form and S-ethyl KH-502 were not identified when the thermal decomposition was proceeded in the open system. 2. KH-502 was stable at 25 and 50$^{\circ}C$, but it was decomposed at 100$^{\circ}C$ following the first-order kinetics at the early stages of decomposition. 3. Rate constants for the thermal decomposition of KH-502 at 100$^{\circ}C$ were in the orders of Cu powder addition 0.344>Cu plate addition 0.21>moisture addition 0.05>closed system=open system=iron addition=pH 5.5 adjustment 0.04>pH 8.5 adjustment 0.027 day$^{-1}$, representing KH-502 was decomposed fast at Cu powder treatment and slow at pH 8.5 adjustment. 4. Half-life for the thermal decomposition of KH-502 at 100$^{\circ}C$ was in the orders of Cu powder addition 2.02

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.10
• /
• pp.99-106
• /
• 2008

5kWh FESS(Flywheel Energy Storage System) using AMB(Active Magnetic Bearing) has been under development and 1st trial system has been finished and run the operating test. Unfortunately, the test result was not satisfactory because FESS could increase the rotational speed up to 9,000 rpm only although the target rotational speed is 18,000rpm. It's because 1st bending mode frequency of flywheel shaft was too low and imbalance response was too big. To achieve the target speed, 1st bending mode and imbalance response must be improved and the whole FESS needed to be designed again. This paper presents the newly designed FESS and what has been changed from the 1st trial FESS to improve 1st bending mode and imbalance response. The experimental results to see how much 1st bending mode frequency was improved are presented, too.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.12-15
• /
• 2002

Korea Power System Protection Setting Rule was used from the rectify 1990's. Thereafter transmission voltage is raised the voltage into 765kV, and introduction to new technology of Power System, and was many of variation but, it is using. The present is using Digital type distance relay for 765kV transmission line protection. If impedance value of transmission line were to value lower than setting, this would be operating and relay setting rule is for 85% into Zone 1 self section, and Zone 2 is a 125%, Zone 3 is a 225%. Which's $15{\sim}25%$ include current transformer error 5%, potential transformer 5%, relay calculation error 5% and margin factor from the field experience. This paper is discussed transmission protective relay and relay setting rule of high voltage power system and we verify the correctness relay setting rule with distance relay using Matlab simulation.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.6
• /
• pp.971-976
• /
• 2012

A 150 kJ compact capacitive pulsed power system (CCPPS) capable of delivering electrical energy into an electrothermal chemical (ETC) gun on a vehicle has been studied. The CCPPS provides pulsed electrical energy into a capillary plasma injector which generates plasma of tens of thousands $^{\circ}K$ in temperature and has a nonlinear resistance depending on the current. The design requirements of the CCPPS are as follows: the maximum power of 250 MW, the pulse width of about 0.6 ms, the volume of no more than 0.5 cubic meter, the efficiency of energy transfer over 80 % and the repetition rate of 4~5 times per minute. The constructed CCPPS is composed of four 37.5 kJ capacitor bank modules in parallel to make a trapezoid pulse shape and to satisfy the design requirements. Each module is designed to achieve high reliability, safety, efficiency and energy density to endure severe operating conditions. The results of the performance test on the CCPPS using a 120 mm ETC gun are described.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.754-757
• /
• 1998

This study was carried out to investigate the effect of replacing silicate by Versenate PS peroxide stabilizer in a peroxide bleaching system of deinked pulp process. To evaluate the possibility of replacement, optimization of pretreatment and caustic in bleaching for stock treated with silicate and Versenate PS were performed. After these performance, residual peroxide content and brightness were measured. Results obtained form this study were summarized as follows : 1. Caustic concentration in bleaching system treated with silicate was optimized at 2.5~3.0%. 2. Caustic concentration in bleaching system treated with Versenate PS was optimized at 1.0~1.5%. 3. Versenate PS alone did not provide satisfying bleaching effect. 4. Bleaching system treated with Versenate PS had potential to reduce silicate. 5. DTPA pretreatment provided higher bleaching efficiency.