• 한국안전학회지
• /
• 제25권6호
• /
• pp.9-13
• /
• 2010

An experimental study for characteristics of soot were conducted at the post-flame region in jet diffusion flames, where carbon dioxide was used as additives in oxidizer stream. Light-extinction method was performed using He-Ne laser with wave length at 632.8nm for the measurement of relative soot density and soot volume fraction with dimensionless extinction coefficient, $K_e$ and mass specific extinction coefficient, ${\sigma}_s$. To increase of resolution, laser light was modified for sheet-form using concave, convex lenses and slit. C/H ratio was introduced for quantitative analysis of soot growth which is expressed by carbonization and dehydrogen. Also transmission electron microscopy(TEM) was used for observation of morphological shape. The results show that the relative soot density in the post-flame region was lower when carbon dioxide was added in oxidizer stream because of reduction of flame temperature.

• Journal of Animal Science and Technology
• /
• 제55권6호
• /
• pp.545-549
• /
• 2013

The optimal conditions for applications of an atmospheric pressure plasma (APP) jet for the inactivation of Salmonella Typhimurium in chicken breast and pork loins were investigated. APP jet treatment for 10 min (versus 5 minutes) showed a higher inactivation of S. Typhimurium in an agar plate, with the best effect at a distance of 20 mm. A treatment on both sides (both-side treatment) for 2.5 + 2.5 min showed a greater inhibition on S. Typhimurium growth compared to single-side treatment for 5 min, with reduction levels of 0.66 log CFU/g in chicken breast and 1.33 log CFU/g in pork loin, respectively. However, there was no significant difference between single-side treatment for 10 min and both-side treatment for 5 + 5 min in chicken breasts and pork loin samples. In conclusion, APP jet treatment conditions, including distance, time, and direction, may affect the inactivation efficiency of S. Typhimurium. In this experiment, distance of 20 mm and both-side treatment were the best conditions. Therefore, the optimal APP jet treatment conditions were evaluated to maximize its practical efficiency.

• 한국재료학회지
• /
• 제17권9호
• /
• pp.453-457
• /
• 2007

Interest in use of ink-jet printing for pattern-on-demand fabrication of metal interconnects without complicated and wasteful etching process has been on rapid increase. However, ink-jet printing is a wet process and needs an additional thermal treatment such as an annealing process. Since a metal ink is a suspension containing metal nanoparticles and organic capping molecules to prevent aggregation of them, the microstructure of an ink-jet printed metal interconnect 'as dried' can be characterized as a stack of loosely packed nanoparticles. Therefore, during being treated thermally, an inkjet-printed interconnect is likely to evolve a characteristic microstructure, different from that of the conventionally vacuum-deposited metal films. Microstructure characteristics can significantly affect the corresponding electrical and mechanical properties. The characteristics of change in microstructure and electrical resistivity of inkjet-printed silver (Ag) films when annealed isothermally at a temperature between 170 and $240^{\circ}C$ were analyzed. The change in electrical resistivity was described using the first-order exponential decay kinetics. The corresponding activation energy of 0.44 eV was explained in terms of a thermally-activated mechanism, i.e., migration of point defects such as vacancy-oxygen pairs, rather than microstructure evolution such as grain growth or change in porosity.

• 한국결정성장학회지
• /
• 제30권5호
• /
• pp.174-182
• /
• 2020

최근 잉크젯 프린팅 기술을 이용한 인쇄전자 분야가 차세대 기술로서 각광받고 있으며, 복수의 프린트 헤드(head)로부터 다양한 잉크 형태의 소재를 정밀하게 출력하여 적층할 수 있는 3D 프린팅 기술에 관한 연구가 활발하게 진행되고 있다. 본 연구에서는 잉크젯 3D 프린팅 기술을 이용하여 광경화성 실리카 잉크와 PVP가 첨가된 나노 구리 잉크로 절연층과 전도층의 복합구조체를 제작하였다. 프린팅 구동 조건과 잉크의 유변학적 거동을 최적화하여 정밀한 광경화 실리카 절연층을 적층 제조하였으며, 절연층의 저항은 2.43 × 10¹³ Ω·cm의 값을 나타내었다. 광경화 실리카 절연층 위에는 액적 간격 제어를 통하여 나노 구리 전도층을 프린팅하였다. PVP 첨가 나노 구리 잉크의 소결은 IPL 광소결 공정을 이용하였으며, 어닐링 온도와 인가 전압 변화에 따른 전기적, 기계적 특성을 확인하였다. 100℃ 어닐링 온도와 700 V IPL 광소결 조건에서 PVP가 첨가된 나노 구리 전도층의 저항은 29 μΩ·cm으로 매우 낮으며, 광경화 실리카 절연층과의 접착력은 매우 우수한 것으로 확인하였다.

• 한국결정성장학회지
• /
• 제28권3호
• /
• pp.123-129
• /
• 2018

고온 열처리 후에도 안정적인 발색 효과를 가지는 디지털 4원색(cyan, magenta, yellow, black; CMYK)의 세라믹 잉크를 활용한 세라믹 잉크젯 프린팅 기술은 다양한 제품의 디지털 이미지를 정확하고 빠르게 인쇄 가능하다는 장점을 가지고 건축 및 세라믹 산업 분야에서 기존 공정을 빠르게 대체하고 있다. 세라믹 잉크젯 프린팅 기술은 무기 안료의 분산 안정성과 함께 적절한 점도와 표면 장력을 필요로 하며 기존에는 이러한 요구조건에 부합하는 유기용매 기반의 잉크가 주로 사용되어져 왔으나 최근에는 VOCs가 발생하지 않는 환경친화적인 세라믹 잉크 소재에 대한 관심이 커지고 있다. 본 연구에서는 $CoAl_2O_4$ cyan 발색 무기안료와 alumino boro-silicate 유리 분말을 사용하여 친환경적인 수계 세라믹 복합잉크를 합성하고, 수계 시스템에서의 유변학적 물성과 분산성을 최적화하여 잉크젯 프린팅 공정에서의 토출성 및 프린팅 특성에 대해 연구하였다. 그 결과, 합성된 수계 세라믹 복합잉크는 점도 및 표면장력 조절을 통해 satellite drop이 발생하지 않는 토출 거동을 보였으며, 유리 기판 위에서도 높은 접촉각으로 인해 잉크 퍼짐 현상이 최소화되며 프린팅되는 것을 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.423-425
• /
• 2001

The Proper Orthogonal Decomposition (POD) technique was applied to investigate the effects of Reynolds number and the characteristics of the organized motions or coherent structures as a function of downstream position from x/D=2 to 6 in a turbulent axisymmetric shear layer at Reynolds numbers of 78,400, 117,600, and 156,800. Data were collected simultaneously using the 138 hot-wire probe used by Citriniti and George (2000). The POD was then applied to a double Fourier transform in time and azimuthal direction of the double velocity correlation tensor. The lowest azimuthal mode for all POD modes, which dominated the dynamics at x=D = 3 in the previous experiments, dies off rapidly downstream. This is consistent with a trend toward homogeneity in the downstream evolution, and suggests that some residual value may control the growth rate of the far jet. On the other hand, for the higher azimuthal modes, the peak shifts to lower mode numbers and actually increases with downstream distance. These mixing layer data, normalized by similarity variables for the mixing layer, collapse at all downstream positions and are nearly independent of Reynolds numbers.

• Journal of Forest and Environmental Science
• /
• 제34권5호
• /
• pp.376-381
• /
• 2018

For the control of oak wilt caused by Raffaelea quercus-mongolicae, an antifungal microorganism, Streptomyces blastmyceticus, was used as a potential agent. Culture suspension of S. blastmyceticus was injected into Quercus mongolicae in the research forest of Kangwon National University by $ChemJet^{(R)}$ trunk injection and Macro-infusion at root flare injection. $Alamo^{(R)}$ (a.i., propiconazole 14.5%), a fungicide currently used for the control of oak wilt in USA, was also treated by both methods to compare the efficacy. For preventive efficacy, culture suspension of the pathogen was inoculated at 1 month after injection of either agent. Tested trees were cut at 3 months after treatment, stained with 1% Fuchsin acid, and then non-conductive area (NCA) and re-isolation frequency (RIF) of oak wilt fungus were compared among treatments. While NCA was the highest as 47.3% in pathogen only treatment, it was the lowest as 16.0% in sterilized water treatment by Macro-infusion. NCAs of Alamo treatment by Macro-infusion and ChemJet injection were 25.3% and 32.1%, respectively. NCA of S.blastmyceticus treatment by ChemJet injection was 32.3%, similar with Alamo treatment's by ChemJet injection. All treatments by either injection method showed significantly lower NCA compared to the pathogen only treatment. These results indicate that S. blastmyceticus injection shows the preventive efficacy against oak wilt disease by suppressing the growth of pathogen injected. NCA of Macro-infusion injection of sterilized water was lower as 16.0%, compared to 21.3% of ChemJet injection. It means that Macro-infusion is more effective in translocation of sterilized water than ChemJet injection by even distribution. RIF from wood discs of treated trees showed high in pathogen only treatment, but relatively low in S. blastmyceticus treatment. RIF results were correlated with NCA results. From the above results, it was confirmed that S. blastmyceticus showed preventive efficacy against oak wilt disease by ChemJet trunk or Macro-infusion at root flare injection.

• 수산해양기술연구
• /
• 제40권2호
• /
• pp.155-160
• /
• 2004

Water jet trajectories and velocity deficits from a high pressurize nozzles were experimentally observed. In this article, several parameters affecting plugging and erosion onto the steam generator tube were quantitatively analyzed. Visualization, velocity distribution, and spray growth rate with different nozzle configurations have been mainly focused using a 2-D PDPA (Phase Doppler Particle Analyzer) system. The results indicated that trajectories along the centerline regardless of their momentum has its potential core region. However, the phenomena from the peripheral part need to be meticulosly considered. Accordingly, it is evident that quantitative velocity deficits at the outer region are outstanding due to the aerodynamical drag and entrainment.

• Wind and Structures
• /
• 제5권2_3_4호
• /
• pp.141-150
• /
• 2002

Numerical simulations based on the ALE finite element method are carried out to examine the aerodynamics of an oscillating circular cylinder when the separated shear flows around the cylinder are stimulated by periodic jet excitation with a shear layer instability frequency. The excitation is applied to the flows from two points on the cylinder surface. The numerical results showed that the excitation with a shear layer instability frequency can reduce the negative damping and thereby stabilize the aerodynamics of the oscillating cylinder. The change of the lift phase seems important in stabilizing the cylinder aerodynamics. The change of lift phase is caused by the merger of the vortices induced by the periodic excitation with a shear layer instability frequency, and the vortex merging comes from the high growth rate, the rapid increase of wave number and decrease of phase velocity for the periodic excitation in the separated shear flows.

• 산업경영시스템학회지
• /
• 제26권3호
• /
• pp.31-38
• /
• 2003

There is boner process of stone manufacturing to become quality down of stone to consolidated micro crack appearance of stone surface and biotite by fire that is to be route process in stone surface by flame of LPG. And then, it is develop that stone surface process equipment by automation for the work method of boner process can be substitute work method by water jet To development of equipment, There is to be down noise and dust. According to remove calamity growth hazardous substance in the work environment, there is to solve workplace avoidance factor.