• 한국전기전자재료학회논문지
• /
• 제14권6호
• /
• pp.466-469
• /
• 2001

In this paper, we evaluated the dielectric properties of XLPE sheet of 22kV power cable, XLPE/semiconductor and XLPE/water/semiconductor depended on electric field and temperature respectively. Dielectric properties and temperature dependency of XLPE sheet of 22kV power cable increase greatly with as temperature increase and have no effect on applied voltage. And we confirmed that tan$\delta$ values in the samples with semiconductor or water layers were higher than those in the samples without them.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.131-134
• /
• 1999

Microstructure modification and electrochemical properties are investigate to estimate the effects of internal chlorides on the steel corrosion in the blended cement systems. According to the test results, slag cement system showed high chloride binding capacity and low corrosion rate. The impedance data showed three distince arcs from lowest(mHz) frequency to highest (MHz) frequency due to product layer, interfacial reaction and bulk matrix. Through the microstructural investigation, fine steel-matrix interface of slag cement system was observed but rough steel-matrix interface of OPC system was observed. Friedel's salt was thought that the substantial material contributed to the chloride binding of slag cement system.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.291-295
• /
• 2005

The PEMFC behavior is quite complex and is influenced by several factors, including composition and structure of electrodes and membrane type. Fabrication of MFA is important factor for proton exchange membrane fuel cell. MFA of PEMFC with hot pressing and direct coating method were prepared, and performances were evaluated and compared each other. The effect of MEA preparation methods, hot pressing methods and direct coating methods, on the cell performance was analyzed by impedance spectroscopy and SEM. The performance of PEMFC wi th direct coat ing method was better than wi th hot pressing method because membrane internal resistance and membrane-:-interfacial resistance were reduced by elimination of hot pressing process in MEA fabrication. In addition the micro structure of MEA with direct coating method reveals uniform interface between membrane and catalyst layer.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.230-234
• /
• 2005

Fabrication of MEA is important factor for proton exchange membrane fuel cell (PEMFC). MEA of PEMFC with hot pressing and direct coating method were prepared, and performances were evaluated and compared each other. The effect of MEA preparation methods, hot pressing methods and direct coating methods, on the cell performance was analyzed by impedance spectroscopy and SEM. The performance of PEMFC with direct coating method was better than with hot pressing method because membrane internal resistance and membrane-interfacial resistance were reduced by elimination of hot pressing process in MEA fabrication. In addition the micro structure of MEA with direct coating method reveals uniform interface between membrane and catalyst layer.

• 한국진공학회지
• /
• 제8권2호
• /
• pp.157-164
• /
• 1999

The post ion implantation has been applied to modify early-grown BN layer and improve the adhesion of the BN films. The effect of ion implantation doses on microstructure and interlayer was investigated by FTIR and HRTEM. And the hardness and delamination life time of N+-implanted BN films were measured. With increasing the ion dose up to $5.0\times10^{15}\textrm{atoms/cm}^2$,the change of IR spectrum is observed. At $5.0\times10^{16}\textrm{atoms/cm}^2$, a drastic transition of cubic phase into hexagonal phase is detected. The change of microstructure of early-grown layers by ion implantation is confirmed using HRTEM. Both microhardness and delamination life time of BN films increase with ion dose. The modification model of early-grown BN layers is briefly discussed based on the displacement per atom and excess boron in the BN film induced by ion irradiation.

• Macromolecular Research
• /
• 제9권1호
• /
• pp.51-65
• /
• 2001

Two-stage emulsion polymerizations of hydrophobic monomers on hydrophilic seed polymer particles were carried out to make core-shell composite particles. It was found that the loci of polymerization in the second stage were the surface layer of the hydrophilic seed latex particles, and that it has resulted in the formation of either eccentric core-shell particles with the core exposed to the aqueous phase or aggregated nonspherical composite particles with the shell attached on the seed surface as many small separated particles. The driving force of these phenomena is related to the gain in free energy of the system in going from the hydrophobic polymer-water interface to hydrophilic polymer-water interface. Thermodynamic analysis of the present polymerization system, which was based on spreading coefficients, supported the likely occurrence of such nonspherical particles due to the combined effects of interfacial free energies and phase separation between the two polymer phases. A hypothetical pathway was proposed to prepare hydrophilic core-hydrophobic shell composite latex particles, which is based on the concept of opposing driving and resistance forces for the phase migration. It was found that the viscosity of the monomer-swollen polymer phase played important role in the formation of particle morphology.

• 한국세라믹학회지
• /
• 제30권3호
• /
• pp.206-214
• /
• 1993

Coherent precipitation of Zn3P2 during Zn diffusion in a GaInAsP/InP heterostructure was studied using high-resolution transmission electron microscopy. Zn-diffusion-induced intermixing of Ga and In across the GaInAsP/InP heterointerface provided a Ga-mixed InP region which was nearly lattice-matched with Zn3P2 crystal and thus allowed thecoherent precipitation of Zn3P2. The Zn3P2 precipitates were preferentially nucleated at stacking faults which were formed to relax interfacial strain built up by the intermixing. The precipitates were grown to planar epitaxial layer along (100) plane in the lattice-matched region. The TEM images and diffraction pettern revealed that the tetragonal Zn3P2 crystals were coherently matched to the fcc structured GaInP matrix by the {{{{ SQRT {2} $\times$ SQRT {2} $\times$2 }} arrangement. The precipitation reaction of Zn3P2 was explained by an atomic migration model based on the kick-out mechanism.

• Transactions on Electrical and Electronic Materials
• /
• 제15권6호
• /
• pp.324-327
• /
• 2014

Germanium (Ge) is a promising material for next generation nanoelectronics and multiple junction solar cells. This work investigated the electrical properties in Cu/p-type Ge Schottky diodes, using current-voltage (I-V) measurements. The Schottky barrier heights were 0.66, 0.59, and 0.70 eV from the forward ln(I)-V, Cheung, and Norde methods, respectively. The ideality factors were 1.92 and 1.78 from the forward ln(I)-V method and Cheung method, respectively. Such high ideality factor could be associated with the presence of an interfacial layer and interface states at the Cu/p-Ge interface. The reverse-biased current transport was dominated by the Poole-Frenkel emission rather than the Schottky emission.

• E2M - 전기 전자와 첨단 소재
• /
• 제11권10호
• /
• pp.94-99
• /
• 1998

Suitable replacement materials for ultrathin SiO2 in deeply scaled MOSFETs such as lattice polarizable films, which have much higherpermittivities than SiO2, have bandgaps of only 3.0 to 4.0 eV. Due to these small bandgaps, the reliability of these films as a gate insulator is a serious concern. Ramped voltage, time dependent dielectric breakdown, and hot carrier effect measurements were done on 190 layers of TiO2 which were deposited through the metal-organic chemical vapor deposition of titanium tetrakis-isopropoxide (TTIP). Measurements of the high and low frequency capacitance indicate that virtually no interface state are created during constant current injection stress. The increase in leakage upon electrical stress suggests that uncharged, near-interface states may be created in the TiO2 film near the SiO2 interfacial layer that allow a tunneling current component at low bias.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2008년도 학술발표회 논문집
• /
• pp.1838-1842
• /
• 2008

본 연구에서는 하구 유입 하천에서 발생하는 염수쐐기의 형상 및 거동특성을 구명하기 위하여 정상상태 염수쐐기 실험을 수행하였다. 길이에 비해 상대적으로 폭이 좁은 개수로의 상류부분에는 담수를 지속적으로 공급할 수 있는 담수공급장치를 설치하였고, 정상상태의 염수쐐기를 발생시키기 위하여 염수수조 측면에 지속적으로 염수를 공급할 수 있는 염수공급수조를 설치하였다. 실험조건은 담수 방류량과 이층류의 밀도차의 영향을 고려한 밀도프루드수(densimetric Froude number)를 기준으로 선정하였다. 실험결과 각 케이스별 염수쐐기의 형상은 중앙부에서 약간의 산포된 양상을 제외하고는 거의 선형을 이루는 것으로 관찰되었다. 경계층의 형상과 두께는 이층류의 농도장을 측정하고 밀도변동성분을 고려한 표준편차를 통하여 산정하였다. 그리고 염수쐐기의 선단부에 해당하는 리차드슨수와 경계층 두께와의 비교 등을 통해서 경계층의 양상을 파악하였다.