• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1707-1709
• /
• 1999

Insulating thin films for strain gauge application, such as $SiO_2$ single layers and $SiO_2/Si_3N_4$ multilayers, are deposited by using both PECVD and RF magnetron sputtering techniques. Micro-structural analysis and electrical characterization are carried out on those films. It has been observed that PECVD films have a smoother surface and a denser micro-structure than sputter films. It should be also found out that the electrical insulation property of $SiO_2$ film can be significantly improved by adding the $Si_3N_4$ layer.

• Journal of the Korean Ceramic Society
• /
• v.24 no.3
• /
• pp.270-276
• /
• 1987

The microstructure and dielectric properties of a SrTiO3-based GBL (Grain Boundary Layer) capacitor were investigated. The 0.6 mol% Nb2O5 doped SrTiO3 was sintered for 3 hr at 1450$^{\circ}C$ in mixed gas(N2/H2) atmosphere. The Nb2O5 promoted the grain growth of the SrTiO3 ceramics was decreased with the amount of Nb2O5. The oxide mixture(PbO, Bi2O3, B2O3) were painted on the reduced specimen and fired at 1000$^{\circ}C$ to 1100$^{\circ}C$ in air. The penetrated oxide mixture into specimen were located in grain boundaries. A SrTiO3-based GBL capacitor had the apparent permittivity of about 3.0${\times}$104, the dielectric loss of 0.01-0.02, and insulating resistance of 108-109$\Omega$.cm. The capacitor had the stable temperature coefficient of capacitance and exhibited dielectric dispersion over 107 Hz. The capacitance-voltage measurements indicated that the grain boundary was composed of the continuous insulating layers.

• Journal of the Korean Society of Safety
• /
• v.31 no.4
• /
• pp.22-26
• /
• 2016

"Always-on" small ventilators are likely to experience thermal decomposition of insulating material due to thermal, electrical, mechanical and environmental influences, and lose insulating properties by the process of oxidation and physiochemical reaction. This increases the risk of electrical fire because of layer short, short circuit, overload and Plastics are usually used to make ventilator and ventilator enclosures since they make less noise and are cheaper. Although more preferred than iron, plastic, a combustible material, has a higher risk of fire. In this study, several experiments were carried out to find out how RCD(Residual Current Protective Device) and Thermal fuses, which are electric motor protection devices, work and what needs to be done to reduce the risk of fire.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.938-940
• /
• 1998

In order to improve insulating character and ability of insulating system of power apparatus, the interfacial and complex structure is widely used. However, the interface or complex structure of insulation materials is reported as a weak point which causes breakdown. As the interface of insulation system degrades its electrical property and eventually causes a failure, the datailed phenomenon analysis is reported. The object of this paper is to evaluate dielectric property of PET film with the interface. The $tan{\delta}$ increased with the existence of semiconducting layer and showed prominent decrease as a function of temperature. Also, the $tan{\delta}$ showed prominent increase as a function of frequency. The dielectric properties of interfacial were affected by the interface characteristics.

• Electrical & Electronic Materials
• /
• v.7 no.1
• /
• pp.15-24
• /
• 1994

For increasing the insulating proper-ties and the reliability of composite materials due to environmental aging, the electrical and mechanical characteristics of moisture absortion specimens and moisture desorption specimens were investigated. After moisture absorption wt% and moisture desorption wt% increased with time, a state of saturation arrived subsequent to a constant time. Moisture absorption constants with the layers of glass fiber showed 0.0117 in 1 layer, 0.0123 in 2 layers and 0.0152 in 3 layers. Electrical and mechanical characteristics dropped significantly with moisture absorbing in composite materials. Although moisture dried completly at 70.deg. C, it is impossible to obtain the electrical and mechanical characteristics before moisture absorption. Many defaults by moisture in composite materials exist at interface between epoxy matrix and filler.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.57-61
• /
• 1999

Electrical stress makes insulating materials aged finally resulting in the dielectric failure. It becomes more and more important to recognize the degree of aging and the life time of the insulating materials since it is directly concerned with the reliability of the insulation system. In this paper, the life time of the Cross-linked Polyethylene(XLPE), the insulation layer in the 154kV-grade power cable, is expected and calculated using statistical and mathematical methods. The simulated results are compared with experimental ones and the life exponent of the material is obtained.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.6
• /
• pp.312-315
• /
• 2004

The monolayer of oxygen atoms sandwiched between the adjacent nanocrystalline silicon layers was formed by ultra high vacuum-chemical vapor deposition (UHV-CVD). This multilayer Si-O structure forms a new type of superlattice, semiconductor-atomic superlattice (SAS). According to the experimental results, high-resolution cross-sectional transmission electron microscopy (HRTEM) shows epitaxial system. Also, the current-voltage (Ⅰ-Ⅴ) measurement results show the stable and good insulating behavior with high breakdown voltage. It is apparent that the system may form an epitaxially grown insulating layer as possible replacement of silicon-on-insulator (SOI), a scheme investigated as future generation of high efficient and high density CMOS on SOI.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.225-228
• /
• 1997

The main fault in this interface is that power cable insulating materials are mainly composed of a double layered structure, XLPE/FPDM laminates in cable joint. In this parer, we instituted the interface of XLPE/EPDM laminates and then investigated the breakdown and conduction characteristics as a function of heat treatment time. The results showed that conduction current was influenced by volatile crosslinking by-products which remained inside the insulating material during the production of XLPE and EPDM, especially during heat treatment process. And conduction current of XLPE/Oil 12500cSt/EPDM was more stable than XLPE/Grease/EPDM from the long heat treatment time. AC breakdown strength of silicone oil itself from the heat treatment was changed during the 4∼12 hour heat treatment time.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.130-131
• /
• 2019

As part of recent low-energy policies, thermal insulation standards for buildings are being tightened every year. In addition, the conventional styrofoam insulating material has a problem that the thickness of the heat insulating material to achieve a standard heat permeability is rapidly increased. Due to the thick insulation, there is a high risk of spreading vulnerable structures such as fire due to lack of space between buildings. On the other hand, the method of using the insulation as a formwork is known to be excellent cost saving effect through the reduction of the formwork usage and the simplification of the external insulation work. In order to solve this problem, this study aims to fabricate a multi-layered insulator that combines high-performance phenolic foam insulation and styrofoam insulation and evaluate the deflection characteristics for use as formwork.

• Applied Microscopy
• /
• v.52
• /
• pp.4.1-4.11
• /
• 2022

Field emission scanning electron microscopy (FESEM) is an essential tool for observing surface details of specimens in a high vacuum. A series of specimen procedures precludes the observations of living organisms, resulting in artifacts. To overcome these problems, Takahiko Hariyama and his colleagues proposed the concept of the "nanosuit" later referred to as "NanoSuit", describing a thin polymer layer placed on organisms to protect them in a high vacuum in 2013. The NanoSuit is formed rapidly by (i) electron beam irradiation, (ii) plasma irradiation, (iii) Tween 20 solution immersion, and (iv) surface shield enhancer (SSE) solution immersion. Without chemical fixation and metal coating, the NanoSuit-formed specimens allowed structural preservation and accurate element detection of insulating, wet specimens at high spatial resolution. NanoSuit-formed larvae were able to resume normal growth following FESEM observation. The method has been employed to observe unfixed and uncoated bacteria, multicellular organisms, and paraffin sections. These results suggest that the NanoSuit can be applied to prolong life in vacuo and overcome the limit of dead imaging of electron microscopy.