• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(2)
• /
• pp.137-140
• /
• 2001

This paper shows an asynchronous comparator circuit for 1.2Gbps signal receiver that converts 1.2Gbps data rate input signals with less than 100㎷ swing to on-chip CMOS compatible voltage levels in a 0.35${\mu}{\textrm}{m}$ CMOS process. Folded-cascode nMOS input stage with source-coupled pMOS input stage cover rail-to-rail input common-mode range. Drastic gain-bandwidth increment due to gain-boosting stage with positive-feedback latch as well as wide input common-mode range make designed circuit be suitable for a fully differential signal receiver. HSPICE simulation results show that worst-case sensitivity is less than 20㎷ and maximum propagation delay is 640-psec. And also we verified 3.97㎽ power consumption with 150㎷ differential swing amplitude at 1.2Gbps.

• Journal of information and communication convergence engineering
• /
• 제17권4호
• /
• pp.285-289
• /
• 2019

A 1.9-GHz linear CMOS power amplifier is presented. An adaptive bias circuit (ABC) that utilizes an AC ground to detect the power level of the input signal is proposed to enhance the linearity and efficiency of the power amplifier. The ABC utilizes the second harmonic component as the input to mitigate the distortion of the fundamental signal. The input power level of the ABC was detected at the AC ground located at the V_DD node of the power amplifier. The output of the ABC was fed into the inputs of the power stage. The input signal distortion was mitigated by detecting the input power level at the AC ground. The power amplifier was designed using a 180 nm RFCMOS process to evaluate the feasibility of the application of the proposed ABC in the power amplifier. The measured output power and power-added efficiency were improved by 1.7 dB and 2.9%, respectively.

• 전자공학회논문지A
• /
• 제30A권5호
• /
• pp.45-51
• /
• 1993

An erbium doped fiber amplifier(EDFA) pumped by aingle 1.48$\mu$m LD was fabricated, and its gain and noise characteristics were measured. As a signal source, 1548 nm wavelength DFB LD was used. The small signal net gain of the EDFA module was 21.8 dB with maximum gain coefficient 0.7dB/mW for the erbium fiber length of 17.6 m, the pump power of 58 mW, and an input signal power of -25 dBm, respectively. The saturation power of the EDFA was 1 dBm for the input signal power of -5 dBm and the noise figure, measured by using an optical spectrum analyzer, was 5.8 dB for the input signal power of -40 dBm.

• 한국인쇄학회지
• /
• 제25권1호
• /
• pp.65-80
• /
• 2007

The input and output device requires precise color representation and CMS (Color Management System) because of the increasing number of ways to apply the digital image into electronic publishing. However, there are slight differences in the device dependent color signal among the input and output devices. Also, because of the non-linear conversion of the input signal value to the output signal value, there are color differences between the original copy and the output copy. It seems necessary for device-dependent color information values to change into device-independent color information values. When creating an original copy through electronic publishing, there should be color management with the input and output devices. From the devices' three phases of calibration, characterization and color conversion, the device-dependent color should undergo a color transformation into a device-independent color. In this paper, an experiment was done where the input device used the linear multiple regression and the sRGB color space to perform a color transformation. The output device used the GOG, GOGO and sRGB for the color transformation. After undergoing a color transformation in the input and output devices, the best results were created when the original target underwent a color transformation by the scanner and digital camera input device by the linear multiple regression, and the LCD output device underwent a color transformation by the GOG model.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1996년도 춘계학술대회
• /
• pp.240-242
• /
• 1996

In this paper, we proposed a method of a hearing aid suitable for the sensorineural hearing impaired. Generally as the sensorineural hearing impaired have narrow audible ranges between threshold and discomfortable level, the speech spectrum may easily go beyond their audible range. Therefore speech spectrum must be optimally amplified and compressed into the impaired's audible range. The level and frequency of input speech signal are varied continuously. So we have to make compensation input signal for frequency-gain loss of the impaired, specially in the frequency band which includes much information. The input sigaal is divided into short time block and spectrum within the block is calculated. The frequency-gain characteristic is determined using the calculated spectrum. The number of frequency band and the target gain which will be added input signal are estimated. The input signal within the block is processed by a single digital filter with the calculated frequency-gain characteristics. From the results of monosyllabic speech tests to evaluate the performance of the proposed algorithm, the scores of test were improved.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2008년도 춘계종합학술대회 A
• /
• pp.285-288
• /
• 2008

In ubiquitous computing environment the biological signal ECG (Electrocardiogram signal) is usually recorded with noise components. Adaptive interference (or noise) canceller do adaptive filtering of the noise reference input to maximally match and subtract out noise or interference from the primary (signal plus noise) input thereby adaptively eliminate unwanted interference from the ECG signal. Measured Stress ECG (or exercise ECG signal) signal have three major noisy component like baseline wander noise, motion artifact noise and EMG (Electro-mayo-cardiogram) noise. These noises are not only distorted signal but also root of incorrect diagnosis while ECG data are analyzed. Motion artifact and EMG noises behave like wide band spectrum signals, and they considerably do overlapping with the ECG spectrum. Here the multidimensional adaptive method used for filtering which is more effective to improve signal to noise ratio.

• 한국정보통신학회논문지
• /
• 제13권8호
• /
• pp.1491-1496
• /
• 2009

본 논문에서는 비상 디젤 엔진 발전기 제어 및 모니터링을 위해 제안된 디지털 기반의 입/출력 인터페이스 회로를 소매한다. 비상 발전기의 동작 상태를 모니터링 하고 제어하기 위해 제어 및 감시 회로는 5개의 아날로그 입력 채널과 2개의 픽업(Pick-up)코일 계측 회로, 브로컨 와이어(Broken Wire) 감지 기능을 가지는 10개의 디지털 입력 채널 및 7개의 릴레이 제어 신호 출력 채널이 요구된다. 본 연구에서는 아날로그 입력 단에 간단한 필터 회로와 포토커플러, 비교기 회로를 이용하여 입력 신호에 대한 신호처리를 수행하였으며, 중요한 릴레이 출력 신호들은 이중으로 단속될 수 있도록 설계하여 오동작을 철저히 방지하였다. 그리고 픽업코일 신호를 디지털 처리하는 회로를 적용하여 속도 신호 입력의 정확성을 향상 시켰다.

• 한국항공우주학회지
• /
• 제45권10호
• /
• pp.863-871
• /
• 2017

헬리콥터 능동진동제어시스템에 널리 이용되는 LMS (least mean square) 알고리즘은 전방경로 (forward path) 전달함수와 에러 신호의 연산을 통해 제어 입력을 계산한다. 에러 신호가 정현파 형태일 경우, 기준 신호에 동기화된 진동수, 위상을 가지는 코사인과 사인 함수의 조합으로 표현될 수 있다. 제어 신호 또한 동일한 진동수를 가지게 되므로 제어 입력의 코사인, 사인 성분의 크기만 계산하고, 기준 신호의 진동수, 위상 정보를 활용하면 제어알고리즘은 단순하게 구현될 수 있다. 제어 입력 신호의 계산은 단순한 행렬 연산으로 구현되고, 제어 명령의 변화는 에러 센서의 주파수에 비해 느리기 때문에 제어알고리즘은 낮은 주파수에서 운용 가능하다. 에러 센서의 코사인, 사인 성분을 추출하는 신호처리 알고리즘을 시뮬링크 모델로 구현하고, PIL (processor in the loop) 모드 시뮬레이션을 통해 실시간 작동 성능을 평가하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 제14회 신호처리 합동 학술대회 논문집
• /
• pp.73-76
• /
• 2001

It is well-known that the convergence rate gets worse when an input signal to an adaptive filter is correlated. In this paper we propose a new adaptive filtering algorithm that makes the convergence rate highly improved even for highly correlated input signals. By introducing an orthogonal constraint between successive input signal vectors, we overcome the slow convergence problem caused by the correlated input signal. Simulation results show that the proposed algorithm yields highly improved convergence speed and excellent tracking capability under both time-invariant and time varying environments, while keeping both computation and implementation simple.

• 대한전자공학회논문지
• /
• 제27권5호
• /
• pp.808-815
• /
• 1990

This paper treats with the design method for the single loop oversampled Sigma-Delta A/D converter with one delay and the digital integrator. Such an integrator was kgenerated by means of the bilinear transform of the analog integrator. The frequency spectrums of the quantizer and the decimator output signal are evaluated by FFT respectively. With the performance evaluation system, the values of SNR are obtained versus the input sinusoidal signal amplitude, frequency, the oversampling ratio, the DC-input level, the loop gain and the limitting value of the integrator. As compared with existing results, values of SNR versus the input signal amplitude and the oversampling ratio for the suggested system are about 6dB higher then previously reported results respectively. Furthermore, this approach achieves an about 60dB input dynamic range.