• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.34 no.1
• /
• pp.41-51
• /
• 2018

In case of evaluating the bond stress of a void deck plate using a wire steel, there is no standard formula considering both the influence on the void and the type of the reinforcing bar. Therefore we proposed a model equation considered the bond characteristics of the void deck plate. A total of 46 specimens was carried out a direct pull-out test and the test variables were the presence of a void body, type of reinforcing bar, the inner cover thickness according to the location of reinforcing bars and bond region. As a result of the comparison between the steel bar and steel wire, the bond stress of the steel wire with the relative rib area of 0.071 is 4.5 ~ 28.58% lower than that of the steel bar with 0.092 and the bond stress reduction rate increases when the inner cover thickness is insufficient. In the case of the inner cover thickness of $1.7d_b$ and $2.7d_b$, the bond stress was reduced to 48.7 ~ 68.4%. In the inner cover thickness was $4.9d_b$ and $5.2d_b$, the bond stresses were equivalent to those of the solid specimens. It was confirmed that the average bond stress and strain were affected by the inner cover thickness. Therefore the predicted model for one module of the void deck plate is proposed and verified by considering the bond characteristics of the void deck plate.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.7 s.238
• /
• pp.805-813
• /
• 2005

The thermal performance of a flat-strip heat pipe with inner grooves and the screen mesh cover was investigated experimentally. The heat pipes were made of 2024 aluminum alloy of which the dimensions were 30 (W) $\times$ 4 (T) $\times$ 150 (L) mm. The cross sectional dimensions of inner groove were 0.4$\times$0.9 mm and the space between grooves was 0.6 mm. To enhance the capillary force, foe screen meshes were attached to cover the grooved inner surface. In the grooved heat pipes without screen mesh cover, the maximum thermal load of 180 W (12 W/$cm^2$) was achieved for operating temperature below $130^{\circ}C$ at horizontal position. The heat pipes with screen mesh cover showed the thermal resistances less than one third of those without screen mesh cover, and showed less fluctuation in the thermal resistance values. Furthermore, the thermal performance of the former exhibited less dependence on the tilt angle and the fill charge ratio.

• Journal of the Korea Concrete Institute
• /
• v.25 no.2
• /
• pp.155-163
• /
• 2013

This study investigated the bond characteristics of embedded deformed steel bar in donut type biaxial hollow slabs. The donut type hollow sphere make concrete inner cover formed between steel bar and hollow sphere due to the hollow shape and arrangement. Generally, inner cover was thinner than outer cover, and some part of donut type biaxial hollow slab has smaller inner cover thickness than $2.5d_b$. It was affected to the bond condition of deformed bar. Furthermore, inner cover thickness changes along the longitudinal deformed bar due to hollow shape. Therefore, donut type hollow slab was divided 3 regions according to the hollow shape such as insufficient region, transition region, sufficient region. Pull-out test were performed to find out the effect of bond condition by the region. Main parameters are inner cover thickness, embedded length and bond location. Bond characteristics of donut type biaxial hollow slab were confirmed through comparison of bond stress-slip relationship, maximum bond strength and bond stress distribution of each regions. And the calculation method of bond strength of donut type biaxial hollow slab was suggested based on the test results.

• Journal of Korean Society of Rural Planning
• /
• v.3 no.1
• /
• pp.23-32
• /
• 1997

The purpose of this study is to analyze structural and ecological characteristics of streams in rural village. The methods used in this study were measuring the section and surveying the vegetation of the stream at three points(upstream, inner village, downstream ) of 10 rural villages. The major findings of this study can be summarized as follows : 1) The average width of streams is 9 m, and the height of banks 3.1 m. the downstreams are the widest(average 10 m), and the inner-villages are the narrowest (average 8 m), and the slopes of basin are 7.33 %, 2.67 %, 1.39 % at upstream, inner-village, downstream respectively. 2) The downstreams are more contaminated than upstreams due to the sewage from the residents, especially livestock wastewater. 3) The dominant species in the streams are Persicaria thunbergii H. Gross (average Cover 17.76 %) and cumulus japonicas Sieb et. Zucc (average Cover 7.75 % ). 4) The average area covered by vegetation is 53.31 % the downstreams are covered 65.7 %, but inner-village area covered by vegetation is 46.6 %. 5) The problem found in this study are severe water contamination, poor accessibility to stream and poor vegetation of inner-village area, etc.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.3
• /
• pp.28-36
• /
• 2010

Today We have three full series of the annals of Joseon Dynasty. Taebaeksan volume which is one of them shows comparatively good maintenance but Taebaeksan volume also decomposed in patches. The size of cover and inner paper were increased in late Joseon Dynasty, but the weight, thickness and basis weight bears no relation to each other. The oxidation index of paper in annals of pre-periods of King Sunjo shows very high value. After the annals of King Sunjo, the oxidation index of paper is very similar to today's Hanji. L.a.b values of inner paper in the Taebaeksan volume are similar generally. The average length of fiber using image analysis soft ware is 8.08~9.92 mm, that like immediate value of measurement. The air fraction of fiber's range is 1.20~2.12%. It lower than today's Hanji. After considering the factors of the length of fiber, air fraction and FE-SEM, we reached that no difference between raw material of inner paper in the Taebaeksan volume.

• Design & Manufacturing
• /
• v.12 no.1
• /
• pp.52-57
• /
• 2018

With the recent strengthening of environmental regulations and the need for cost reduction, excavators, a type of construction equipment, are being miniaturized while components are being developed in consideration of stability. In the case of excavator press parts, mainly high-strength steel sheets are being used to enhance stability and reduce weight. However, in the case of high-strength materials, there is a need to research product forming methods to reduce Springback in defects arising in parts assembly due to Springback that result from the internal residual stress that occurs in press forming being released after product forming. Accordingly, regarding the tank cover, an excavator press-forming part, this study selected a method to reduce distortion through analysis of the Springback occurrence rate and Springback causes through a forming analysis. A forming analysis was conducted for the Springback of the tank cover. Deformations of 13.714 mm in the upper part and 6.244 mm in the inner part of the product occurred, while wrinkles occurred on the sides of the product due to uneven thickness. A forming analysis was conducted for the major shapes of the product to investigate the causes of Springback. Distortion deformation due to the bead in the center of the product was confirmed to be a large factor. A Springback reduction method of correcting uneven thickness in the product sides, a Springback reduction method of removing the bead, and a correction method of restriking after the final forming were used in a forming analysis to determine the degree of Springback reduction. For the forming method to correct uneven thickness in the sides, deformation was reduced by 12% in the upper side compared to the existing model, but deformation in the inner side increased by 1%. For the restriking forming method, deformation decreased by 25% in the upper side and 13% in the inner side. For the bead removal method, deformation decreased by 28% in the upper side and 13% in the inner side, the largest Springback correction results. This indicates that the bead has a large affect on Springback.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.4
• /
• pp.449-455
• /
• 2013

When a missile is launched, a fracture-type canister cover should be properly broken by a collision with a missile or inner pressure of a canister. The fracture performance of a canister cover should be evaluated by a test using a real missile; however, it is unrealistic due to high cost and time restriction in a design stage. In this study, a test technique is newly developed to predict fracture performance of a canister cover. The test was design to have same kinetic energy with a real missile test when the cover is collide with a missile. The effectiveness of the suggested test technique was proved by comparing the test result with that of a real missile test.

• Journal of Korean Society of Rural Planning
• /
• v.15 no.2
• /
• pp.19-26
• /
• 2009

The purpose of this study is to build Island biogeography in the basic concept of landscape ecology in South Korea by draw relationship between the species side of quantitative habitats and forest area surveyed in the national database based on investigation of the 2nd natural environment. In addition, try to present criterion of habitats character category after understanding habitats character of emergence area side of quality habitats based on the type of formatting. Species and forest area relationship analyzed using correlation analysis and simple regression analysis. Also habitat character limited composition ratio of neighboring land cover and analyzed using hierarchical cluster analysis to classify type of habitat. As a result, we found that forest area is correlated with number of species, forests which is bigger than 100ha are more important of increase in species' population. And according to land cover composition ratio, bird's classified types of forest inner species, forest edge species, forest outer species and mammal's classified types of forest inner species, forest general species, forest edge species. We suggest that study of species-forest area relationship and emergence habitat character be used as some management plans of species' conservation, protection and restoration.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.55 no.3
• /
• pp.181-189
• /
• 2019

Discarding juvenile fishes under girth 16 cm nearly equal to inner perimeter of codend mesh size collected by a cover net method in bottom trawl. The body size of the main five species (mackerel, horse mackerel, sea bream, melon seed and black throat seaperch) was measured for their body length, girth, weight, height and width and analyzed size selectivity. Frequency of penetrating fish as retention in a cover net was less than 40% of total number of juvenile discarding fish. The most of body length or girth of five species were significantly different between in the codend and in the cover net. The 50% selection girth in the cover net ranged 8-11 cm were smaller than those in the codend ranged 9-13 cm by the species respectively. The 50% selection body length was significantly related with the ratio of body height (H) by body width (W) both for in the codend or in the cover net while 50% selection girth was not significantly related with H/W. Furthermore 50% selection fish size by fish species between in the codend and in the cover net was not significantly different both in body length or girth. Therefore, the girth selectivity represented possibly as one unique value regarding fish body shape was considered as more useful method for multi-species catch in trawl.

• KIEAE Journal
• /
• v.10 no.3
• /
• pp.11-16
• /
• 2010

This paper has attempted to investigate the change in soil moisture volume and temperature of architecture by planting ground(soil thickness and soil mixture ratio) and ground cover plants(Sedum sarmentosum, Zoysia japonica, Chrysanthemum zawadskii) for middle region green roof system. For this, a test was conducted on the roof of Konkuk University building from April 2009 to October 2009. In terms of treatment, five types(SL, $P_7P_1L_2$, $P_6P_2L_2$, $P_5P_3L_2$, $P_4P_4L_2$) depending on soil mixture ratio and two types(15cm, 25cm) by soil depth were created. Results of soil moisture volume by soil mixture ratio in the 15cm soil thickness showed that the difference was significance between simple soil and mixture soil treatment, however, the statistical significance was not recognized according to soil mixture ratio. In case of 25cm soil thickness, soil moisture volume by soil mixture ratio was more higher 7Vol.%~10Vol.% in the mixture soil than simple soil treatment. In terms of districts planted ground cover plants, soil volume moisture differed among plants in the order Zoysia japonica 17.74 Vol.%$34.86^{\circ}C$, district non-planted $27.49^{\circ}C$, Sedum sarmentosum $25.11^{\circ}C$, Chrysanthemum zawadskii $23.08^{\circ}C$, Zoysia japonica $24.45^{\circ}C$ respectively So, concrete surface showed more higher $5^{\circ}C{\sim}15^{\circ}C$ than other things among the all the time. Result of inner temperature of the architecture and soil, it was measured inner of architecture $25.69^{\circ}C$, inner district non-planted $24.29^{\circ}C$, Chrysanthemum zawadskii $23.90^{\circ}C$, Zoysia japonica $24.02^{\circ}C$, Sedum sarmentosum $25.13^{\circ}C$, respectively.