• 한국추진공학회지
• /
• 제13권1호
• /
• pp.19-26
• /
• 2009

과산화수소 단일추진제 추력기의 응답성에 대한 실험적 연구를 수행하였다. 촉매베드의 특성을 배제하고 추력기 설계 인자에 따른 응답특성을 살펴보기 위해 $MnO_2$/$Al_2O_3$를 주 촉매로 고정하였다. 세 가지 50 N 급 추력기를 이용하여 인젝터 방식, ullage volume, 촉매 펠렛 크기, 반응기 부피에 따른 응답 속도를 측정하였다. 측정 결과 16-20 mesh 크기 촉매, shower head 인젝터를 사용한 경우 점화지연, 압력 상승 및 하강시간은 각각 14, 108, 94 ms로 상용 하이드라진 추력기 응답성에 근접한 특성을 보였다.

• 대한기계학회논문집B
• /
• 제26권6호
• /
• pp.788-794
• /
• 2002

In liquid rocket engine, propellant feed rate is proportional to approximately square root of the pressure difference between injector head and combustion chamber. This ΔP depends on the engine design, but in general on the order of 50psi. However, during ignition period, especially for the pressurized feed system, combustion chamber pressure is almost atmospheric and large ΔP causes over flow of propellants which may lead to catastrophic accident due to hard start. Hard start may be prevented by applying cavitating venturi or/and two step ignition. In cavitating venturi, evaporated propellants near the venturi throat become chocked and flow rate depends on only upstream condition. In two step ignition propellants are supplied to the liquid engine in two different flow rate. First step, to avoid hard start, small amount of propellants are supplied to build up chamber pressure in safe zone, then full propellants to ensure design pressure. In this study, both cavitating venturi and two step ignition method were used for the hot test and hard start problem was completely solved.

• 대한기계학회논문집B
• /
• 제27권1호
• /
• pp.9-16
• /
• 2003

According as the industry was developed, the pollution of the environment and atmosphere rose up to the surface. So, the focus is now concentrated on the engines of affinity for nature. And the investigators make more effort to the improvement in the performance of engines, depending to the prices of oil and the anxiety about the exhaustion of the fossil fuel go up. So the GDI engines head up for these necessities. In this experimental study, the spray flow characteristics for a commercial injector equipped in the present GDI engine were investigated, which had a strong influence on the engine performance and emissions. The experiment was performed at the injection pressures of 1, 3, 5 and 7MPa under the atmospheric condition. A PDPA system was used to specify the flow characteristics of the spray. Also, the global spray behavior classified into three regions as leading, main spray and vortex cloud region, was analyzed by using a visualization system. And the regions were compared with each other.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제26회 춘계학술대회논문집
• /
• pp.171-176
• /
• 2006

연료 과농 가스발생기에 대한 실험적 연구가 수행되었다. 연소 성능에 주요한 영향을 미치는 분사기 헤드에는 1.5의 리세스 수를 갖는 내부 혼합형 이중 스월 분사기 37개가 배치되었다. 본 논문에서는 연소실 길이, 직경, 그리고 교반링 등의 연소실 설계 변경에 따른 실물형 가스발생기의 연소 안정성 특성에 대하여 살펴보았다. 연소시험 결과 공진 주파수가 고주파 영역에서 생성됨에 따라 동압의 세기는 전반적으로 감소하였으나, 연소 불안정을 완전히 억제시키지는 못하는 것으로 나타났다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.125-129
• /
• 2009

본 논문에서는 대형 우주 발사체에 적용 가능한 추력 75톤급 액체로켓엔진 연소기의 기본설계에 대해 기술하였다. 이 연소기는 진공추력 74.8 ton, 진공비추력 306.9 sec, 연소실 압력 60 bar, 추진제 유량 243.6 kg/s, 연소특성속도 1730 m/sec을 갖는다. 연소기의 성능에 미치는 연소특성속도, 추력계수 그리고 비추력에 대해 알아보았고, 연소기의 기하학적인 형상에 대해서도 기술하였다. 75톤급 액체로켓 엔진 연소기는 분사기를 장착한 연소기 헤드, 재생냉각 채널을 가지고 있는 연소실로 구성되어 있다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.225-228
• /
• 2009

추력 75톤급 액체로켓엔진용 기술개발/검증 시제인 가스발생기의 연소시험이 수행되었다. 가스발생기 분사기 및 헤드의 성능을 먼저 확인하기 위해 heat-sink 형태의 연소실이 사용되었다. 본 논문에서는 연소시험을 위한 준비상황 및 기술검증시제 연소시험에서 얻어진 압력, 온도 분포, 압력 섭동 등의 결과들을 설명하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.255-258
• /
• 2002

Liquid rocket engines using liquefied natural gas (LNG) or methane as a fuel is known to have several good characteristics, such as high specific impulse compared to other hydrocarbon fuels, environment-friendly exhaust gas, low production cost, and re-usability with low soot generation in the cooling channel. In this study, experimental combustion chambers capable of using LNC and $CH_{4}$ are being researched through experimental firing tests, and within easy range of eyes' inspection, there are the periodical existence of soot or discoloration in the chamber wall surface. This result means that mixture ratio of oxidizer and fuel fluctuates periodically between outer-row injectors in the mixing head in the circumferential direction. Therefore, based on this phenomenon, the variation of mixture ratio near the chamber wall caused by the spill pattern of a shear coaxial injector was analyzed quantitatively and the thermal heat flux Into the cooling channel is modified. Then, the calculated and modified results are compared with the measured ones.

• 대한기계학회논문집A
• /
• 제31권1호
• /
• pp.11-17
• /
• 2007

In this paper, we present a design, analysis, fabrication and performance test of the novel DoD metal-jet system for application to the high-density and high-temperature-melting materials. The theoretical analysis of the metal-jet nozzle system is derived by using electro-mechanical analogy. Based on the theoretical analysis results, we design the metal-jet print head system and fabricate the metal-jet system, which can eject the droplet of lead-free metal solder in high-temperature. In the experimental test, we set up the test apparatus for visualization of the droplet ejection and measure the ejected droplet volume and velocity. As a result, the diameter, volume and the velocity of the ejected droplet are about 65 $\mu$m $\sim$ 70 $\mu$m, 145p1 $\sim$ 180 pl and 4m/s, which shows quite good agreement with the theoretical analysis results of the 75 $\mu$m-diameter and 220 pl-volume of droplet. In comparison with the experimental result, the errors of diameter and volume are 7% $\sim$ 13% and 18 $\sim$ 34%, respectively.

• 한국자동차공학회논문집
• /
• 제16권3호
• /
• pp.73-79
• /
• 2008

Atomization speed of diesel fuel injected from 8-hole nozzle is faster than that of 7-hole nozzle because the hole diameter of 8-hole nozzle is smaller than that of 7-hole nozzle. But both insufficient distance between the fuel sprays and short penetration of injected sprays through 8-hole nozzle hole cause many harmful effects on combustion. In this study, we installed the 8-hole injectors to diesel 2.0 liter class engine, and optimized in-cylinder swirl and penetration via selecting and matching proper cylinder head and combustion bowl. Through this process, we found out the performance and emission potential of 8-hole nozzle installed engine are better than those of 7-hole nozzle installed one.

• International Journal of Automotive Technology
• /
• 제2권2호
• /
• pp.63-75
• /
• 2001

This paper describes the development of THC reduction technologies compliant with SULEV regulations. Technologies embodied by the developmental work include improvement of fuel spray atomization, quick warm-up through coolant control shut of, and acceleration of fuel atomization for the fast rise of cylinder head temp inside the water jacket as well as the improvement of combustion state. The technologies likewise entail reduced HC while operating in lean A/F condition during engine warm-up with the cold lean burn technology, individual cylinder A/F control for improvement of catalytic converting efficiency, after-treatment such as thin-wall catalyst, HC-adsorber and EHC and etc, through vehicle application evaluation in cold start. We carried out an experimental as well as a practical study against SULEV regulations, and the feasibility of adopting these items in vehicle was likewise investigated.