• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1658-1662
• /
• 2007

The tire uneven wear has been an ongoing concern for a long time, and one of customer's complaints too. This paper deals with uneven wear improvement of passenger car tires, to have tested the tire wear levels by each wheel alignment set (according to changing toe and camber) using taxis. The pre-set wheel alignments on test vehicle were gained by energy friction simulation of tire. The result of this experiment was as follows : First, verified the effects of initial wheel alignment (adjusted at Curb Vehicle Weight) to minimize tire uneven wear. Second, tire uneven wear makes tire life much shorter than even wear does.

• 대한조선학회지
• /
• 제8권1호
• /
• pp.95-102
• /
• 1971

Since the fuel oil of the bunker C grade, which is commonly burnt in the large marine diesel engine, causes the corrosive wear of cylinder liners and piston rings, a cylinder oil of high alkality is frequently used to prevent the wear. This practice, however, brings us an another problem to cause the abnormal wear. In this study the author made an investigation of the mechanism of the abnormal wear by the experiments surveying the influences of the alkality of a cylinder oil and the temperature of cylinder wall on the wear. The major results obtained from this study are as follows; A cylinder oil of low alkality is clearly effective for the preventation of the abnormal wear. Therefore, it is recommended that, prio to using a cylinder oil of high alkality, a cylinder oil of low alkality should be used until bringing an end to the initial wear. It is also observed that the abnormal wear depends largely on the temperature of the cylinder wall, that is, the higher the temperature goes up the severer the wear grows.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.184-192
• /
• 2001

Cam/tappet wear is one of the critical concerns in valve train deign. Maximum contact stress and minimum oil film thickness between the cam and tappet are usually checked for the estimation of wear characteristics. If the two extreme cases arise simultaneously, there is a strong possibility of cam/tappet wear. In this paper, effects of valve train layout on the wear characteristics were studied. Especially for swinging arm type valve trains, initial geometric layout must be very carefully defined to avoid wear problems. The study was performed fur an end pivot type OHC valve train, which had severe wear problems. Analysis results show that some geometric parameter affect very sensitively on the wear characteristics. Experiments were also performed for the original and modified valve trains, which strongly support the analysis results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1684-1689
• /
• 2007

Fretting wear is one of the important degradation mechanisms of steam generator tubes in the nuclear power plants. Especially, impact fretting wear occurred between steam generator tubes and tube support plates or anti-vibration bar. Various tests have been carried out to investigate the wear mechanisms and to report the wear coefficients. Those are fruitful to get insight for the wear damage of steam generator tubes; however, most wear researches have concentrated on sliding wear of the steam generator tubes, which may not represent the wear loading modes in real plants. In the present work, impact fretting tests of steam generator tube were carried out. A wear progression model for impact-fretting wear has been investigated and proposed. The proposed wear progression model of impact-fretting wear is as follows; oxide film breaking step at the initial stage, and layer formation step, energy accumulation step and finally particle torn out step which is followed by layer formation in the stable impact-fretting progress. The wear coefficient according to the work-rate model has been also compared with one between tube and support.

• 대한기계학회논문집A
• /
• 제32권10호
• /
• pp.817-822
• /
• 2008

Fretting wear is one of the important degradation mechanisms of steam generator tubes in the nuclear power plants. Especially, impact fretting wear occurred between steam generator tubes and tube support plates or anti-vibration bar. Various tests have been carried out to investigate the wear mechanisms and to report the wear coefficients. Those are fruitful to get insight for the wear damage of steam generator tubes; however, most wear researches have concentrated on sliding wear of the steam generator tubes, which may not represent the wear loading modes in real plants. In the present work, impact fretting tests of steam generator tube were carried out. A wear progress model for impact-fretting wear has been investigated and proposed. The proposed wear progress model of impact-fretting wear is as follows; oxide film breaking step at the initial stage, and layer formation step, energy accumulation step and finally particle torn out step which is followed by layer formation in the stable impact-fretting progress. The wear coefficient according to the work-rate model has been also compared with one between tube and support.

• Tribology and Lubricants
• /
• 제36권5호
• /
• pp.262-266
• /
• 2020

Herein, we present a numerical investigation of wear analysis of sliding systems with a constant speed subjected to Archard's wear law. For this investigation, we compared two methods: eigen-wear analysis and adaptive meshing technique. The eigen-wear analysis is advantageous to predict the evolution of contact pressure due to wear using the initial contact pressure and contact stiffness. The adaptive meshing technique in finite element analysis is employed to obtain transient wear behavior, which needs significant computational resources. From the eigen-wear analysis, we can determine the appropriate element size required for finite element analysis and the time increment required for wear evolution by a dimensionless variable above a certain value. Since the prediction of wear depends on the maximum contact pressure, the finite element model should have a reasonable representation of the maximum contact pressure. The maximum contact pressure and wear amount according to this dimensionless variable shows that the number of fine meshes in the contact area contributes more to the accuracy of the wear analysis, and the time increment is less sensitive when the number of contact nodes is significantly larger. The results derived from a two-dimensional wear model can be applied to a three-dimensional wear model.

• 산업경영시스템학회지
• /
• 제17권31호
• /
• pp.91-98
• /
• 1994

Most of machines are physically or chemically degenerated by continuous usage. There- fore, a preventive maintenance is necessary. Producing defects are caused by process shift in mean and variance which are due to three types of degeneration. We develope the function of process variance from the experimental data and determine the optimal tool wear limit and the initial setting position of tool by considering the percent defective cost and the preventive maintenance cost.

• 대한기계학회논문집A
• /
• 제32권11호
• /
• pp.930-936
• /
• 2008

This paper studies the effect of pad at initial stage and wear during braking on the dynamic contact pressure distribution. Wear is influenced by variable factor (contact pressure, sliding speed, radius, temperature) during dynamic braking and variation in contact pressure distribution. Many researchers have conducted complex eigenvalue analysis considering wear characteristic with Lim and Ashby wear map. The conventional analysis method is assumed the pad has smooth and flat surfaces. The purpose of this paper is to validate that wear rate induced by braking is considered for the precise squeal prediction. After obtaining pad wear from experiment, it is incorporated with FE model of brake system. Finally, the comparisons in fugitive nature of squeal will be carried out between the complex eigenvalue analysis and noise dynamometer experiment.

• 한국기계가공학회지
• /
• 제7권4호
• /
• pp.3-9
• /
• 2008

The ion implantation technology is generally used in order to improve surface mechanical properties, especially tribological properties, of engineering metals. In this study, experimental works were carried out to investigate the surface properties, such as hardness, wear quantity, wear rate and friction force, of a nitrogen ion implanted tool steel STD11 under dry condition. Specimens for the wear test were made to investigate the influences of the initial ion implantation temperature and the total ion radiation. Wear properties, such as the wear quantity and the wear rate, of the nitrogen ion implanted tool steel were considerably improved, especially under the low sliding speed and the low applied load.

• 대한기계학회논문집A
• /
• 제31권11호
• /
• pp.1083-1092
• /
• 2007

The objective of the present paper is to evaluate the effect of the evolution of contact surface profile caused by fretting wear on fatigue life of press-fitted shaft by means of an analytical method based on experimental data. A finite element analysis was performed to analyze the stress states of press-fitted shaft, considering the worn contact profiles of shaft. The fatigue lives of the press-fitted shaft reflecting the evolution of contact stress induced by fretting wear were evaluated by stress-life approach using fatigue notch factor. It is found that the stress concentration of contact edge in press-fitted shaft decreases rapidly at the initial stage of total fatigue life, and its location shifts from the contact edge to the inside with increasing number of fatigue cycles. Thus the change of crack nucleation position in press-fitted shaft is mainly caused by the stress change of contact edge due to the evolution of contact surface profile by fretting wear. Furthermore, the estimated fatigue lives by stress-life approach at the end of running-in period of the fretting wear process corresponded well to the experimental results. It is thus suggested that the effect of fretting wear on fatigue life in press fits is strongly related to the evolution of surface profile at the initial stage of total fatigue life.