• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.11
• /
• pp.1-8
• /
• 2011

One of the most important parameters that limit maximum output power of transistor is breakdown. InAlAs/InGaAs/GaAs Metamorphic HEMTs (MHEMTs) have some advantages, especially for cost, compared with InP-based ones. However, GaAs-based MHEMTs and InP-based HEMTs are limited by lower breakdown voltage for output power even though they have good microwave and millimeter-wave frequency performance with lower minimum noise figure. In this paper, InAlAs/$In_xGa_{1-x}As$/GaAs MHEMTs are simulated and analyzed for breakdown. The parameters affecting breakdown are investigated in the fabricated 0.1-${\mu}m$ ${\Gamma}$-gate MHEMT device having the modulation-doped $In_{0.52}Al_{0.48}As/In_{0.53}Ga_{0.47}As$ heterostructure on the GaAs wafer using the hydrodynamic transport model of a 2D commercial device simulator. The impact ionization and gate field effect in the fabricated device including deep-level traps are analyzed for breakdown. In addition, Indium mole-fraction-dependent impact ionization rates are proposed empirically for $In_{0.52}Al_{0.48}As/In_xGa_{1-x}As$/GaAs MHEMTs.

• Korean Journal of Materials Research
• /
• v.9 no.5
• /
• pp.460-466
• /
• 1999

The deep level electron traps in AP-MOCVD GaAs/undoped Al\ulcornerGa\ulcornerAs/n-type GaAs heterostructures have been investigated by means of Deep Level Transient Spectroscopy DLTS). In terms of the experimental procedure, GaAs/undoped Al\ulcornerGa\ulcornerAs/n-type GaAs heterostructures were deposited on 2" undoped semi-insulating GaAs wafers by the AP-MOCVD method at $650^{\circ}C$ with TMGa, AsH3, TMAl, and SiH4 gases. The n-type GaAs conduction layers were doped with Si to the target concentration of about 2$\times$10\ulcornercm\ulcorner. The Al content was targeted to x=0.5 and the thicknesses of Al\ulcornerGa\ulcornerAs layers were targeted from 0 to 40 nm. In order to investigate the electrical characteristics, an array of Schottky diodes was built on the heterostructures by the lift-off process and Al thermal evaporation. Among the key results of this experiment, the deep level electron traps at 0.742~0.777 eV and 0.359~0.680 eV were observed in the heterostructures; however, only a 0.787 eV level was detected in n-type GaAs samples without the Al\ulcornerGa\ulcornerAs overlayer. It may be concluded that the 0.787 eV level is an EL2 level and that the 0.742~0.777 eV levels are related to EL2 and residual oxygen impurities which are usually found in MOCVD GaAs and Al\ulcornerGa\ulcornerAs materials grown at $630~660^{\circ}C$. The 0.359~0.680 eV levels may be due to the defects related with the al-O complex and residual Si impurities which are also usually known to exist in the MOCVD materials. Particularly, as the Si doping concentration in the n-type GaAs layer increased, the electron trap concentrations in the heterostructure materials and the magnitude of the C-V hysteresis in the Schottky diodes also increased, indicating that all are intimately related.ated.

• Journal of the Korean Vacuum Society
• /
• v.19 no.2
• /
• pp.134-140
• /
• 2010

We have investigated the contactless electroreflectance (CER) properties of $In_{0.5}(Ga_{1-x}Al_x)_{0.5}P$/GaAs double heterostructures grown by metal-organic chemical vapour deposition (MOCVD). The CER measurements on the sample were studied as a function of temperature, modulation voltage ($V_{ac}$), and dc bias voltage ($V_{bias}$). Five signals observed at room temperature are related to the GaAs, $In_{0.5}Ga_{0.5}P$, $In_{0.5}(Ga_{0.73}Al_{0.27})_{0.5}P$, $In_{0.5}(Ga_{0.5}Al_{0.5})_{0.5}P$, and $In_{0.5}(Ga_{0.2}Al_{0.8})_{0.5}P$ transitions, respectively. From the temperature dependence of CER spectrum, the Varshni coefficients and broadening parameters were determined and discussed. In addition, we found that the behavior of the CER amplitude for the reverse bias is larger than that of the forward.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1321-1323
• /
• 1998

We investigated drain leakage current in GaAs power MESFET. The device we studied by 20 simulation has a $1000{\AA}$ thick AlGaAs buffer layer under n-GaAs active layer. The calculation shows that the leakage current through GaAs substrate is significantly reduced by the buffer layer.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.6
• /
• pp.225-231
• /
• 2016

The valence band maximum (VBM) and conduction band minimum (CBM) of Al-doped GaInAsSb alloys substrated on GaSb are calculated by using an analytic approximation based on the tight binding method. The relative positions of the VBM and CBM between Al-GaInASSb and GaSb determine band alignement type, valence band offset (VBO) and conductin band offset (CBO) for the heterojunctions. In this study, aluminium doping is assumed to be substituted in the cation site and limited up to 20 % because it can easily oxidize and degrade materials. It is found that the Al-doped alloys exhibit type-II band alignments over the entire composition range and make the band gaps increase, whereas the VBO and CBO decrease. The decreasing rate of VBO is higher than that of CBO, which implies the Al components play a decisive role in controlling electrons at the interface. The Al-dopled GaInAsSb alloy has a direct band gap induced by $E({\Gamma})$ with a considerable distance from the E(L) and E(X), however, $E({\Gamma})$ approaches to E(L) and E(X) in the high Sb concentration (Sb > 0.7-0.8) which might affect the electron mobility and degrade the optical quality.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.10
• /
• pp.1202-1208
• /
• 1988

The electron density and electronic states in n- AlGaAs/GaAs heterointerface are calculated by using classical- and quantum-mechanics, respectively. We examine the effects of spacer layer thickness and doping concentration in AlGaAs layer on 2DEG density. Also, the dependences of electronic states of 2DEG upon temperature and acceptor concentration in GaAs layer are investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.10-12
• /
• 1996

AlGaAs/GaAs Heterojunotion Bipolar Transistors (HBTs) with various emitter areas were fabricated and the device size dependence on the current gain was examined. With the different emitter areas, the passivated devices having the same peripheral length were fabricated and measured. The measured base current density in the Gummel plots shows an ideality factor of nearly 2. It is found that as the emitter area becomes small, the base current density with the ideality factor of 2 increases linearly, and as the emitter perimeter/area ratio becomes large, the surface recombination current density component increases. The current gain performance in AlGaAs/GaAs HBTs is mainly determined by either the larger emitter area or the smaller ratio of the emitter perimeter to the emitter area. These results will be compared with experimental works for GaInP/GaAs HBTs

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.1
• /
• pp.30-39
• /
• 1991

The influence of physical parameters (Al mole fraction, thickness, doping concentration) in the window and emitter on the efficiency characteristics of heteroface p-$Al_{x}Ga_{1-x}As/p-GaAs/n-GaAs/n^{+}$-GaAs solar cell is investigated. The maximum efficiency theoretically calculated in this device is obtained when a thickness of the window is in a range of (400-1000))$\AA$and a thickness/doping concentration of the emitter is in a range of (0.5-0.8)$\mu$m/(1-7)${\times}10^{17}cm^{-3}$, respectively. Also is the efficiency improved according to the increase of Al mole fraction in the indirect gap window(0.41${\le}x{\le}1.0$). The optimum designed heteroface cell with an area of 0.165cm$^2$fabricated using MOCVD exhibits an active area conversion efficiency of 17%, having a short circuit current density of 21.2mA/cm\ulcorner an open circuit voltage of 0.94V, and a fill factor of 0.75 under ELH-100mW/cm$^2$illumination.

• The Korean Journal of Ceramics
• /
• v.4 no.1
• /
• pp.43-46
• /
• 1998

We have investigated the formation and thermal stability of cobalt aluminide(CoAl) thin films on GaAs. In order to obtain cobalt-aluminide thin films, we deposited a multilayer of Co/Al on GaAs, and subsequently annealed the samples at 80$0^{\circ}C$ for 30 min. After annealing, single-phase cobalt aluminide was produced showing a flat and uniform interface with GaAs. which indicates that cobalt aluminide (CoAl) is thermally stable with GaAs. In addition, the adherence and mechanical properties of the as-deposited, and annealed Co/Al multilayer structure on GaAs are compatible with those required for device fabrication processes. The electrical property of the CoAl/GaAs contact shows rectifying characteristics, indicating that the diodes were usable as rectifying gate electrodes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.205-205
• /
• 2013

테라헤르쯔(terahertz: THz)파는 0.1~10 THz 의 범위로 적외선과 방송파 사이에 광대역 주파수 스펙트럼을 차지하고 있으며 직진성, 투과성, 그리고 낮은 에너지 (meV)를 가지고 있어 비 파괴적이고 무해한 장점을 지니고 있다. Ti:sapphire laser와 같은 femto-pulse source 등이 많은 발전이 되어 현재 많은 연구와 발전이 이루어지고 있다. femto-pulse source를 이용한 THz 응용에서는 높은 저항, 큰 전자 이동도, 그리고 아주 짧은 전하수명의 기판을 요구하는데 저온에서 성장한 (low-temperature grown : LT) GaAs는 격자 내에 Gallium 자리에 Arsenic이 치환 하면서 AsGa antisite가 발생하여 전하수명을 짧아지는 것을 응용하여 가장 많이 이용되고 있다. 현재 THz 응용분야에서 보다 작고 가격경쟁력이 있는 광통신을 이용한 THz photomixer등이 활발히 연구 하고 있다. 광섬유 내에서 손실과 분산이 최소값을 가지는 부분이 1.55 ${\mu}m$ 부근이고 In0.53Ga0.47As 기판을 이용하였을 때 여기에 완벽하게 만족하게 된다. 하지만 LT-InGaAs 의 경우 AsGa antisite로 인하여 carrier lifetime은 짧아지지만 높은 n-type 전하밀도를 가지게 된다. 이때 Be을 doping하여 전하밀도를 보상하여 높은 저항을 유지해야 하는데 Be의 활성화를 위해서는 열처리를 필요로 한다. 하지만 열처리를 하면 carrier lifetime이 길어지기 때문에 carrier lifetime과 저항을 적절히 조율해야 한다. 이는 물질자체의 특성이기 때문에 InGaAs는 GaAs보다 낮은 amplitude와 짧은 cut-off frequency를 가진다. 본 연구에서는 보다 높은 저항을 얻기 위하여 molecular beam epitaxy를 이용하여 semi-insulating InP:Fe 기판위에 격자 정합된 InGaAs:Be/InAlAs multi quantum well (MQW)를 온도별 ($250{\sim}400^{\circ}C$), 주기별 (50~150)로 성장을 하였고 이때 InGaAs layer의 Be doping level은 $2{\times}1018\;cm^{-3}$, Ex-situ annealing은 $550^{\circ}C$에서 10분으로 고정 하였다. THz 발생 실험에서는 InGaAs/InAlAs MQW은 4000 pA로 1,000 pA를 가지는 InGaAs epilayer보다 4배 높은 전류 신호를 얻을 수 있었고 모든 샘플이 2 THz에서 cut-off frequency를 가지고 있었다. THz 검출 실험에서는 LT-InGaAs:Be epilayer LT-InGaAs:Be/InAlAs, HT-InGaAs/InAlAs 샘플이 각각 180, 9000, 12000 pA의 전류신호를 가지고 있었고 모든 샘플이 2 THz에서 cut-off frequency를 가지고 있었다. HT-InGaAs/InAlAs MQW를 이용한 검출실험에서는 InGaAs layer가 defect free이지만 LT-InGaAs:Be/ InAlAs MQW 보다 높은 전류 신호를 얻을 수 있었다. 이는 InAlAs layer가 저항만 높이는 것뿐만 아니라 carrier trapping layer로써의 역할도 하는 것으로 사료된다.