• Geophysics and Geophysical Exploration
• /
• v.6 no.2
• /
• pp.57-63
• /
• 2003

For the dectection of small cavity in the hard rock, we investigated the feasibility of crosswell travel-time tomography and Kirchhoff migration technique. In travel-time tomography, first arrival anomaly caused by small cavity was investigated by numerical modeling based on the knowledge of actual field information. First arrival delay was very small (<0.125 msec) and detectable receiver offset range was limited to 4m with respect to $1\%$ normalized first arrival anomaly. As a consequence, it was turned out that carefully designed survey array with both sufficient narrow spatial spacing and temporal (<0.03125 msec) sampling were required for small cavity detection. Also, crosswell Kirchhoff migration technique was investigated with both numerical and real data. Stack section obtained by numerical data shows the good cavity image. In crosswell seismic data, various unwanted seismic events such as direct wave and various mode converted waves were alto recorded. To remove these noises und to enhance the diffraction signal, combination of median and bandpass filtering was applied and prestack and stacked migration images were created. From this, we viewed the crosswell migration technique as one of the adoptable method for small cavity detection.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.53-60
• /
• 2009

Motion estimation for H.264/AVC video CODEC is very complex and requires a huge amount of computational efforts because it uses multiple reference frames and variable block sizes. We propose the architecture of high-performance integer-pixel motion estimation circuit based on fast algorithms for multiple reference frame selection, block matching, block mode decision and motion vector estimation. We also propose the architecture of high-performance interpolation circuit for sub-pixel motion estimation. We described the RTL circuit in Verilog HDL and synthesized the gate-level circuit using 130nm standard cell library. The integer-pixel motion estimation circuit consists of 77,600 logic gates and four $32\times8\times32$-bit dual-port SRAM's. It has tile maximum operating frequency of 161MHz and can process up to 51 D1 (720$\times$480) color in go frames per second. The fractional motion estimation circuit consists of 22,478 logic gates. It has the maximum operating frequency of 200MHz and can process up to 69 1080HD (1,920$\times$1,088) color image frames per second.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.1
• /
• pp.49-55
• /
• 2007

To improved the multi-resolution fast hierarchical motion estimation by using de-interlacing algorithm that is effective in term of both performance and VLSI implementation, is proposed so as to cover large search area field-based as well as frame based image processing in SoC design. In this paper, we have simulated a various picture mode M=2 or M=3. As a results, the proposed algorithm achieved the motion estimation performance PSNR compare with the full search block matching algorithm, the average performance degradation reached to -0.7dB, which did not affect on the subjective quality of reconstructed images at all. And acquiring the more desirable to adopt design SoC for the fast hierarchical motion estimation, we exploit foreground and background search algorithm (FBSA) base on the dual arithmetic processor element(DAPE). It is possible to estimate the large search area motion displacement using a half of number PE in general operation methods. And the proposed architecture of MHME improve the VLSI design hardware through the proposed FBSA structure with DAPE to remove the local memory. The proposed FBSA which use bit array processing in search area can improve structure as like multiple processor array unit(MPAU).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.443-451
• /
• 2010

This paper describes a fully integrated CMOS low-IF mobile-TV RF tuner for Band-III T-DMB/DAB applications. All functional blocks such as low noise amplifier, mixers, variable gain amplifiers, channel filter, phase locked loop, voltage controlled oscillator and PLL loop filter are integrated. The gain of LNA can be controlled from -10 dB to +15 dB with 4-step resolutions. This provides a high signal-to-noise ratio and high linearity performance at a certain power level of RF input because LNA has a small gain variance. For further improving the linearity and noise performance we have proposed the RF VGA exploiting Schmoock's technique and the mixer with current bleeding, which injects directly the charges to the transconductance stage. The chip is fabricated in a 0.18 um mixed signal CMOS process. The measured gain range of the receiver is -25~+88 dB, the overall noise figure(NF) is 4.02~5.13 dB over the whole T-DMB band of 174~240 MHz, and the measured IIP3 is +2.3 dBm at low gain mode. The tuner rejects the image signal over maximum 63.4 dB. The power consumption is 54 mW at 1.8 V supply voltage. The chip area is $3.0{\times}2.5mm^2$.

• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.67-72
• /
• 1992

The growth of Ti on Si(111)-$7{\times}7$ and the formation of epitaxial C54 $TiSi_2$ were investigated by using reflection high energy electron diffraction(RHEED) and high resolution transmission electron microscopy(HRTEM). Polycrystalline Ti layer is grown on the amorphous Ti-Si interlayer which is formed at the Ti/Si interface by Ti deposition on Si(111)-$7{\times}7$ at room temperature (RT). HRTEM lattice image and transmission electron diffraction(TED) showed that epitaxial C54 $TiSi_2$ grown on Si substrate with 160 ML of Ti on Si(111)-$7{\times}7$ surface at RT, followed by annealing at $750^{\circ}C$ for 10 min in UHV. Thin single crystal Si overlayer with [111] direction is grown on $TiSi_2$ surface when $TiSi_2$/Si(111) is annealed at ${\sim}900^{\circ}C$ in UHV, which was confirmed by Si(111)-$7{\times}7$ superstructure.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.5
• /
• pp.599-610
• /
• 2005

Purpose: The success of the bonding between electroformed gold and ceramic is dependent on the surface treatment of the pure gold coping. The purpose of this study was to evaluate the bonding strength between the electroformed gold and ceramic with varying surface treatment. Materials and methods: A total of 32 disks,8 were using conventional ceramometal alloy, 24 were using electroforming technique as recommended by manufacturer, were prepared. 24 electroformed disks were divided 3 groups according to surface treatment, i.e. 50 microns aluminium oxide sandblasting(GES-Sand), gold bonder treatment(GES-Bond) and $Rocatec^{TM}$ system(GES-Rocatec). For control group of conventional alloy 50 microns aluminium oxide treatment was done(V-Supragold). Energy dispersive x-ray analysis and scanning electron microscope image were observed. Using universal testing machine, shear bond strength and bonding failure mode at metal-porcelain interface were measured. Results and Conclusion: The following conclusions were drawn: 1. In the energy dispersive x-ray analysis, the Au was main component in electroformed gold(99.9wt%). After surface treatment, a little amount of $Al_2O_3(2.4wt%)$ were found in GES-Sand, and $SiO_2(4wt%)$ in GES-Bond. In GES-Rocatec, however, a large amount of $SiO_2(17.4wt%)$ were found. 2. In the scanning electron microscopy, similar pattern of surface irregu larities were observed in V-Supragold and GES-Sand. In GES-Bond, surface irregularities were increased and globular ceramic particles were observed. In GES-Rocatec, a large amount of silica particles attached to metal surface with increased surface irregularities were observed. 3. The mean shear bond strength values(MPa) in order were $22.9{\pm}3.7(V-Supragold),\;22.1{\pm}3.8(GES-Bond),\;20.1{\pm}2.8(GES-Rocatec)\;and\;13.0{\pm}1.4(GES-Sand)$. There was no significant difference between V-Supragold, GES-Bond, and GES-Rocatec. (P>0.05) 4. Most bonding failures modes were adhesive type in GES-Sand. However, in V-Supragold, GES-Bond and GES-Rocatec, cohesive and combination failures were commonly observed. From the result, with proper surface treatment method electroformed gold may have enough strength compare to conventional ceramometal alloy.

• Journal of Digital Contents Society
• /
• v.16 no.1
• /
• pp.63-70
• /
• 2015

In this paper, we estimate the life cycle from acceleration life test about the hard disk of disk array of image storage of PACS. Webuil distribution was selected by the Anderson-Darling goodness-of-fit test with data of down time at $50^{\circ}C$ and $60^{\circ}C$. The equality test of shape parameter and scale parameter was conducted, so that the probability distribution estimated from data of down time at $50^{\circ}C$ and $60^{\circ}C$ was not statistically significant. The shape parameter was 1.0409, The characteristic life was 24603.5 hours at normal user condition($30^{\circ}C$) by the analysis of weibull-arrhenius modeling which included the acceleration factor of temperature, and The activation energy was 0.5011 eV through arrhenius modeling. The failure analysis of the failure samples of acceleration test and the samples of market return was conducted, so that the share percentage of failure mode was detail difference but the rank of share percentage was almost same. This study suggest the test procedure of acceleration test of hard disk drive in PACS using environment, and help the life estimation at manufacture and use.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.3
• /
• pp.303-309
• /
• 2007

Statement of problem. The effect of gold electroforming on gold alloy was not studied. Purpose. This in vitro study investigate the effect of gold electroforming on gold-silver-palladium alloy. Material and methods. Three pieces of gold strips had undergone the electroforming procedures on one side and then half of the side again electroformed. The set mode for this study was program 1 ($200{\mu}m$). And the processing time was 15min (1/20 time to form $200{\mu}m$ coping). The confocal laser scanning microscope (PASCAL 5, Carl Zeiss, Bernried, Germany) was used to measure the thickness of the pure gold layer electroformed on the gold strips. Half of the gold strip was coated two times with electroformed gold, and the other half one time. The data from the cone focal laser system was processed to get the vertical profile of the strips and the difference of the vertical height between the double coated and single coated layer was regarded as the thickness of the gold coating. The layer thickness value to built 3D image of the cone-focal laser was set $0.5{\mu}m$. Next to the measurement of the thickness of the coating, the Vicker's hardness test was done. It was performed on the double coated surface, single coated surface and non-coated surface (back side) three times each. Results. The mean thickness value gained from gold electroforming technique was measured to be $22{\mu}m$ for sample 1, $23{\mu}m$ for sample 2, $21{\mu}m$ for sample 3. In the same condition of time, power and the amount of electrolyte, the data showed no difference between samples. According to the results of variance analysis, the differences among the variations in number of coating were statistically insignificant (p>0.05), meaning that the two times of gold electroforming coating did not change the hardness of gold-silver-palladium alloy. Conclusion. The test of thickness of gold coating proved the coherency of the gold electroforming procedure, in other words, when the power, the exposed surface area, processing time and the amount of electrolytes were set same, the same thickness of gold would be coated on. The hardness test showed that the electroformed gold coating did not change the hardness of the gold-silver-palladium alloy when it is coated not more than $45{\mu}m$.

• Journal of Korea Port Economic Association
• /
• v.26 no.4
• /
• pp.329-353
• /
• 2010

This paper deal with government logistics policy in related low carbon in China. The government policy of promoting low-carbon way is more dependent on the top-down enforcement rather than voluntary market principles. It will succeeded in transforming the environment-friendly image, to focus on creating a mindset the company can go on voluntary carbon-reduction. The three factors of low-carbon economy and the new energy and industrial development policy is technology and funding, and that most of the government's policy has a crucial role. Due to the nature of the Chinese economy, government policies impact on the development of the industry is very important, and even for China's industrial restructuring of the logistics industry in the areas of government policy support for green economic growth, its role is expected to be very large. In Future, Chinese government will promote low carbon policies through the optimization of the logistics network to reduce energy waste, pursue the low carbon-reduction of logistics machinery and equipment, and develop an mode to appropriate demand for green low-carbon economic growth.

• The Research Journal of the Costume Culture
• /
• v.4 no.2
• /
• pp.113-124
• /
• 1996

This research was designed to find out what is a distictive feature of the design elements of Korean women's costume and its influence by analizing the trend of Korean women's constume during the period of 1890 and 1995. The research was analized by a total of 854 random samples of clothing styles collected from materials in the museums and from articles of three leading newspapers and one of the best women's magazines in Korea. The changing trend of Korean women's costume was found out to be as follows: 1. In around 1910s, the trend of Korean women's costume has been changed into two-tier structure of both Korean and Western styles, and the typical and traditional Korean women's street wears such as 'Chang-ot' and 'Tsdechima' have been gradually diminished. 2. From 1920s, length of the Korean skirt, which was unnecessarily long and inconvenient, has been getting shorter for the convenience of walking. In addition, Korean women's underwear has become simplified, and sports wear could be seen for the first time in Korea. 3. During 1960s, the Western clothing styles have been increased rather than Korean styles as the street wear of the Korean women. 4. In 1970s, blue jeans, mini-skirts and casual wears have become a trend or fashion for women in Korea. 5. In 1980s, a fashion of unisex mode has arrived in this country, and from the year of 1987, wearing of panties among the Korean women has been increased rather than skirts wearing for the street wear. 6. During 1990s, various forma of complex styles came into being in such styles as so-called 'orange class style,' 'protruding navel T-shirts' and 'runner wear speedy.' From mid-1990s, Korean women have turned out to prefer the cute and light costumes by placing emphasis on the image of intellectual, professional and functional wears. The changing special feature of the Korean women's clothing designs could be distinctively observed during 1960s as the modernization policies in Korea have been processed during the period. The clothing trend before 1960 was to change and to solve problems of inconvenient and impractical wears, but the trend after 1960 was seen as a change to confirm a trend of the world fashion. From mid-1990s, however, preference of Korean women's self-conceited conception socially and an unquestionable changing pattern of Korean women's life.