• Journal of the Korean institute of surface engineering
• /
• v.44 no.6
• /
• pp.260-263
• /
• 2011

GZO/ITO double layered films were deposited on unheated non-alkali glass substrates by RF magnetron sputtering using an ITO ($SnO_2$: 10 wt%) and GZO($Ga_2O_3$: 5.57 wt%) ceramic targets, respectively. The electrical resistivity of GZO/ITO films depends on the thickness ratio between the GZO film and ITO film. With increasing ITO film thickness, the resistivity of GZO/ITO films decreased which due to large increase in the Hall mobility. Also, the crystallinity of GZO/ITO film was improved with an increase in ITO thickness which was evaluated by X-ray diffraction. The average transmittance of the films was more than 85% in the visible region, which is slightly higher than ITO single layer films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.478.1-478.1
• /
• 2014

We investigated $MoO_3$ graded ITO electrodes for organic solar cells (OSCs) without PEDOT:PSS buffer layer. The effect of $MoO_3$ thickness on the electrical, optical, and structural properties of $MoO_3$ graded ITO anodes prepared by RF/DC magnetron co-sputtering system using $MoO_3$ and ITO targets was investigated. At optimized conditions, we obtained $MoO_3$ graded ITO electrodes with a low sheet resistance of 13 Ohm/square, a high optical transmittance of 83% and a work function of 4.92 eV, comparable to conventional ITO films. Due to the existence of $MoO_3$ on the ITO electrodes, OSCs fabricated on $MoO_3$ graded ITO electrode without buffer layer successfully operated. Although OSCs fabricated on ITO anode without buffer layer showed a low power conversion efficiency of 1.249%, OSCs fabricated on $MoO_3$ graded ITO electrode without buffer layer showed a outstanding cell performance of 2.545%. OSCs fabricated on the $MoO_3$ graded ITO electrodes exhibited a fill factor of 61.275%, a short circuit current of 7.439 mA/cm2, an open circuit voltage of 0.554 V, and a power conversion efficiency of 2.545%. Therefore, $MoO_3$ graded ITO electrodes can be considered a promising transparent electrode for cost efficient and reliable OSCs because it could eliminate the use of acidic PEDOT:PSS buffer layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.301-301
• /
• 2010

In order to enhance the efficiency of the organic solar cells, the effects of plasma surface treatment with using $CF_4$ and $O_2$ gas on the anode ITO were studied. The polymer solar cell devices were fabricated on ITO glasses an active layer of P3HT (poly-3-hexylthiophene) and PCBM ([6,6]-phenyl C61-butyric acid methyl ester) mixture, without anode buffer layer, such as PEDOT:PSS layer. The metallic electrode was formed by thermally evaporated Al. Before the coating of organic layers, ITO surface was exposed to plasma made of $CF_4$ and $O_2$ gas, with/without heat treatment. In order to identify the effect the surface treatment, the current density and voltage characteristics were measured by solar simulator and the chemical composition of plasma treated ITO surface was analyzed by using X-ray photoelectron spectroscopy(XPS). In addition, the work function of the plasma treated ITO surface was measured by using ultraviolet photoelectron spectroscopy(UPS). The effects of plasma surface treatment can be attributed to the removal organic contaminants of the ITO surface, to the improvement of contact between ITO and buffer layer, and to the increase of work function of the ITO.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.885-886
• /
• 2003

A bilayer is used as an anode electrode for organic electroluminescent devices. The bilayer consist of an ultrathjn ZnO layer adjacent to an hole-transporting layer and an Indium tin oxide(ITO) outerlayer. We tried to bring low the barrier between the devices as deposited ZnO films on ITO substrates. We fabricated the organic EL structure consisted of Al as cathode, $Al_{2}O_{3}$ as electro transport layer, Alq3 as luminously layer, triphenyl diamine(TPD) as hole transport layer and ZnO(l nm )/ITO(l50 nm) as anode. The result of this experiment was not good compared with the case of using ITO, Nevertheless, at this structure we obtained the lowest turn-on voltage as the value of 19 V and the good brightness (6200 $cd/m^{2}$) of the emission light from the devices. Then the quantum efficiency was to be 1.0%.

• Journal of the Optical Society of Korea
• /
• v.13 no.1
• /
• pp.65-74
• /
• 2009

Device quality indium tin oxide (ITO) films are deposited on glass substrates and ultra-thin diamond-like carbon films are deposited as a buffer layer on ITO by a pulsed Nd:YAG laser at 355 nm and 532 nm wavelength. ITO films deposited at room temperature are largely amorphous although their optical transmittances in the visible range are > 90%. The resistivity of their amorphous ITO films is too high to enable an efficient organic light-emitting device (OLED), in contrast to that deposited by a KrF laser. Substrate heating at $200^{\circ}C$ with laser wavelength of 355 nm, the ITO film resistivity decreases by almost an order of magnitude to $2{\times}10^{-4}\;{\Omega}\;cm$ while its optical transmittance is maintained at > 90%. The thermally induced crystallization of ITO has a preferred <111> directional orientation texture which largely accounts for the lowering of film resistivity. The background gas and deposition distance, that between the ITO target and the glass substrate, influence the thin-film microstructures. The optical and electrical properties are compared to published results using other nanosecond lasers and other fluence, as well as the use of ultra fast lasers. Molecularly doped, single-layer OLEDs of ITO/(PVK+TPD+$Alq_3$)/Al which are fabricated using pulsed-laser deposited ITO samples are compared to those fabricated using the commercial ITO. Effects such as surface texture and roughness of ITO and the insertion of DLC as a buffer layer into ITO/DLC/(PVK+TPD+$Alq_3$)/Al devices are investigated. The effects of DLC-on-ITO on OLED improvement such as better turn-on voltage and brightness are explained by a possible reduction of energy barrier to the hole injection from ITO into the light-emitting layer.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.2
• /
• pp.55-59
• /
• 2005

ITO/Ni/ITO thin films were deposited on the PET by RF magnetron sputtering. Dependance of the process parameters such as deposition pressure, positions of Ni layer, on the transmittance, reflectance and sheet resistance of ITO/Ni/ITO film were investigated. When the Ni layer is placed at the center of ITO and deposition pressure is low, ITO/Ni/ITO films showed better optical and electrical properties. At these conditions, the transmittance, reflectance and sheet resistance of the ITO film were $90\%,\;0.38\%$ and $185\Omega/\Box$ respectively.

• Korean Journal of Materials Research
• /
• v.17 no.10
• /
• pp.516-520
• /
• 2007

Indium tin oxide, which is used as transparent conducting layer in flexible device, is deposited on PET film by a magnetron sputtering in 300 mm wide roll-to-roll process (vacuum web coating). Sheet resistance, specific resistance and transmittance is differed by sputtering parameters such as working pressures, oxygen partial pressure, and thickness of ITO layer. ITO layer is deposited about 90 nm at roll speed of 0.24 m/min and its sputtering power is 3 kW. From the XRD spectrum deposited ITO layer is verified as amorphous. Under working pressure varied from $3{\times}10^{-4}\;Torr$ to $2{\times}10^{-3}\;Torr$, sheet resistance is lowest at the working pressure of $1{\times}10^{-3}\;Torr$ and its value is from $110\;{\Omega}/{\square}$ to $260\;{\Omega}/{\square}$ at the thickness of 90 nm. Oxygen partial pressure also varies sheet resistance and is optimized at the regime from 0.2% ($1.8{\times}10^{-6}\;Torr$) to 0.6% ($6{\times}10^{-6}\;Torr$). In this oxygen partial pressure sheet resistance is lower than $150\;{\Omega}/{\square}$. As ITO layer thickness increases, sheet resistance decreases down to $21\;{\Omega}/{\square}$ and specific resistance is about $7.5{\times}10.4{\Omega}cm$ in 340 nm thickness ITO layer. Transmittance is measured at the wavelength of 550 nm and is about 90% for 180 nm thickness ITO/PET.

• Journal of Sensor Science and Technology
• /
• v.7 no.2
• /
• pp.97-102
• /
• 1998

Organic thin film EL devices using PPV(poly (p-phenylenevinylene)) as emitter were fabricated on various conditions and structures, their electro-optical properties were estimated. Fabricated EL devices had structures of single layer(ITO(indium tin oxide)/PPV/Mg), double layer(ITO/PVK(poly(N-vinylcarbazole))/PPV/Mg and ITO/PPV/Polymer matrix + PBD/Mg) and three layer (ITO/PVK/PPV/PS(polystyrene)+PBD(butyl-2-(4-bipheny])-5-(4-tert-butylphenyl-1,3,4-oxadiazole))/Mg), their electro-optical characteristics were compared with each other. In structure of double layer (ITO/PPV /Polymer matrix + PBD/Mg), the used polymer-matrices were PMMA(poly(methyl methacrylate), PC(polycarbonate), PS and MCH(side chain liquid crystalline homopolymer). When PS as a hole transport layer was used, the luminance characteristics on concentration of PBD was obtained. In results, current-voltage-luminance curves of fabricated devices had characteristics of tunneling effect and the device showed a stable light emitting.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.1
• /
• pp.37-43
• /
• 2022

In this study, we investigated the optical, electrical and exothermic characteristics of ITO/Ag/ITO multilayer structures prepared with various Ag thicknesses on quartz and PI substrates. The transparent conducting properties of the ITO/Ag/ITO multilayer films depended on the thickness of the mid-layer metal film. The ITO/Ag (14 nm)/ITO showed the highest Haccke's figure of merit (FOM) of approximately 19.3×10^-3 Ω^-1. In addition, the exothermic property depended on the substrate. For an applied voltage of 3.7 V, the ITO/Ag (14 nm)/ITO multilayers on quartz and PI substrates were heated up to 110℃ and 200℃, respectively. The bending tests demonstrated a comparable flexibility of the ITO/Ag/IT multilayer to other transparent electrodes, indicating the potential of ITO/Ag/ITO multilayer as a flexible transparent conducting heater.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.57.1-57.1
• /
• 2010

ITO(Indium Tin Oxide)는 전도도와 투과도 특성이 뛰어나 디스플레이, 태양전지, LED 등 여러 산업에서 전극 물질로 널리 사용 되어져 왔다. 최근 ITO의 사용이 급격히 증가하면서 이에 대한 연구가 활발히 진행되고 있다. ITO는 막의 특성을 좋게 하기 위하여 증착 시 Ar gas와 함께 $O_2$가스를 첨가하기도 한다. 본 연구에서는 산소 분압에 따른 ITO 박막의 전기적, 광학적 특성에 대하여 연구하였다. Corning사의 eagle 2000 glass 기판위에 스퍼터링을 이용하여 ITO layer를 증측하였고, 증착시, $O_2$ partial pressure를 0 - 0.5%까지 0.1% 간격으로 가변하였다. 증착된 샘플은 Sinton사의 UV-vis 장비를 이용하여 광학적 특성을 측정하였고, Hall measurement 장비를 이용하여 전기적 특성을 측정하였다. ITO 박막은 $O_2$의 partial pressure가 증가할수록 향상된 전기적, 광학적 특성을 나타내었다.