• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.1
• /
• pp.151-157
• /
• 2013

In this paper, a comparative analysis of PBTI induced device degradation in nanowire n-channel junctionless and inversion mode Multiple-Gate MOSFET(MuGFETs) has been performed. It has been observed that the threshold voltage is increased after PBTI stress and the threshold voltage variation of junctionless device is less significant than that of inversion mode device. However the degradation rate of junctionless device is less significant than that of inversion mode device. The activation energy of the device degradation is larger in inversion mode device than junctionless device. In order to analyze the more significant PBTI induced device degradation in inversion mode device than junctionless device, 3-dimensional device simulation has been performed. The electron concentration in inversion mode device is equal to the one in junctionless device but the electric field in inversion mode device is larger than junctionless device.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.3
• /
• pp.139-143
• /
• 2022

In this study, Among the electromagnetic induction power generation (EMG) techniques, the design specifications of the RFPM were set, and a suitable test prototype was manufactured through finite element analysis (FEM, 2D) required for characteristic calculation. In addition, a dedicated testing device (Dynamo-Tester) was designed and manufactured to measure and analyze the test prototype. The test product was measured with a test device and the result is analyzed to suggest a method that can be applied by generating as much output power as possible to charge the battery of the wearable IT device using actual kinetic energy of the human body. As a result of the test, the output power was 1.679W and the efficiency was 79.31% under the conditions of rotation speed of 780.9rpm, torque of 0.264kgf/cm, and load current of 73.6~73.9mA. Therefore, it was analyzed that it was possible to charge the wearable device with the output of the ultra-small RFPM pendulum generator.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.25 no.1
• /
• pp.65-80
• /
• 2007

The input and output device requires precise color representation and CMS (Color Management System) because of the increasing number of ways to apply the digital image into electronic publishing. However, there are slight differences in the device dependent color signal among the input and output devices. Also, because of the non-linear conversion of the input signal value to the output signal value, there are color differences between the original copy and the output copy. It seems necessary for device-dependent color information values to change into device-independent color information values. When creating an original copy through electronic publishing, there should be color management with the input and output devices. From the devices' three phases of calibration, characterization and color conversion, the device-dependent color should undergo a color transformation into a device-independent color. In this paper, an experiment was done where the input device used the linear multiple regression and the sRGB color space to perform a color transformation. The output device used the GOG, GOGO and sRGB for the color transformation. After undergoing a color transformation in the input and output devices, the best results were created when the original target underwent a color transformation by the scanner and digital camera input device by the linear multiple regression, and the LCD output device underwent a color transformation by the GOG model.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.5
• /
• pp.1039-1044
• /
• 2005

A Multi-channel serial device using the embedded Linux system is designed for a remote controlling and monitoring system. The proposed device consists of a FIFO, a state machine, and an interrupter. The device program written in embedded Linux enables the effective programming of device. While the conventional multi-channel serial devices accesses every individual serial devices, the proposed device accesses the multi-channel serial device as if it is a single serial device. The device efficiently performs the multi-channel serial input/output operation and has fast access time than the conventional multi-channel serial device.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.29 no.3
• /
• pp.5-16
• /
• 2021

In this study, the applicability of the MBR(Membrane Bio Reactor) process of oxygen dissolve was evaluated through comparison and evaluation of the efficiency of oxygen dissolve device and conventional aeration device in the explosive tank within the MBR process. The organic matter and ammonia oxidation by oxygen dissolve device were evaluated, and the efficiency of persaturation was evaluated by applying real waste water (anaerobic digester effluent treatement from food waste). SCOD and ammonia removal rates for oxygen dissolve device and conventional aeration device methods were similar. However, it was determined that the excess sludge treatment cost could be reduced as the yield of microorganisms by oxygen dissolve device is about 0.03 g MLSS-produced/g SCOD-removed lower than that of microorganisms by conventional aeration device. The removal rates of high concentrations of organic matter (4,000 mg/L) and ammonia (1,400 mg/L) in anaerobic digester effluent treatment from food waste were compared to the conventional aeration device and the oxygen dissolve device organic matter removal rate was approximately 13% higher than that of the conventional aeration device. In addition, for MLSS, the conventional aeration device was 0.3 times higher than for oxygen dissolve device. This is believed to be due to the high progress of sludge autooxidation because the dissolved oxygen is sufficiently maintained and supplied in the explosive tank for oxygen dissolve device. Therefore, it was determined that the use of oxygen dissolve device will be more economical than conventional aeration device as a way to treat wastewater containing high concentrations of organic matter.

• Journal of IKEEE
• /
• v.8 no.1 s.14
• /
• pp.136-144
• /
• 2004

From the AC analysis results utilizing a two dimensional device simulator, the ac equivalent-circuit modeling of the ESD protection devices is executed. It is explained that the ac equivalent circuit of the NMOS protection transistor is modeled by a rather complicated form and that, depending on the frequency range, the error can be large if it is modeled by a simple RC serial circuit. It is also shown that the ac equivalent circuit of the thyristor-type pnpn protection device can be modeled by a simple RC serial circuit. Based on the circuit simulations utilizing the extracted equivalent circuits, the effects of the parasitics in the protection device on the characteristics of LNA are examined when the LNA, which is one of the important RF circuits, is equipped with the protection device. It is explained that a large error can result in estimating the circuit characteristics if the NMOS protection transistor is modeled by a simple capacitor. It is also confirmed that the degradation of the LNA characteristics by incorporating the ESD protection device can be reduced a lot by adopting the suggested pnpn device.

• Clean Technology
• /
• v.23 no.3
• /
• pp.248-255
• /
• 2017

In dismantling factories for recycling, it is important to input actual working data to a personal computer (PC) in order to monitor the work results and related recycling rate of the inputs. This should be performed with a keyboard, a mouse, or other devices. But when a worker is working in the factory, it could be bothersome or time consuming to go to the PC. Especially, workers who works at dismantling factories have a generally low education level are scared to use a PC, which could be used as a pretext for not using the PC. In some cases, data input is performed by a worker after the day's job. In this case, it could take additional time, the worker can make more mistakes, and the data could be unreliable. In this study, we developed a man-machine interface (MMI) device using a safety helmet. A joystick-like device, pushbuttons, and a radio frequency (RF) device for wireless communication is equipped in a safety helmet. This MMI device has functions similar to a PC mouse, and it has a long communication distance. RF is used because it consumes less battery power than Bluetooth. With this MMI device, workers need not go to a PC to input data or to control the PC, and they can control the PC from a long distance. The efficiency of PCs in a factory could be increased by using the developed MMI system, and workers at the dismantling factories could have less reluctance in using the PC.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.3
• /
• pp.134-140
• /
• 2021

This study relates to the development of a wearable device that can identify a personal location using low-power GPS and IMU based on energy harvesting. The energy harvesting technology using a piezoelectric device was applied for the development of personal location identification, and made it possible to acquire precise personal location data using GPS and IMU. As a result of the experiment, it was confirmed that GPS and IMU data were normally received. The personal location identification device can be prepared for an accident by identifying a personal location in a disaster area, etc., and the user will be able to use it easily regardless of time, place, and environment. It is expected that it can be used in various fields such as leisure and health care.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2000.11a
• /
• pp.149-152
• /
• 2000

This paper is on the edgelit device with external control function and change of light color by dimming control of high flux LED. It the light is projected the transparent body via reflector, the mixture of light is uniform and it is proved by simulation and experimentation. To improve the light efficiency of the device, the research on reflector materials and the distortion of LED input owing to the transistor's characteristics are need.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.79-79
• /
• 2000

In this Paper, the PC input device using MEMS gyros and accelerometer is newly developed, so that it can measure rotation rate and linear acceleration of the human body in space. In General, the human motion has 6 degree of freedom but 2 degree of freedom is enough PC monitor with 2D display. Therefore the simple method is proposed to achieve minimum degree of freedom. It is also applied to the PC mouse. This method can be expanded to the input device for internet set-top box or internet TV.