• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.75-79
• /
• 2003

We studied InP etch results in high density planar inductively coupled $BCl_3$ and $BCl_3$/Ar plasmas. The investigated process parameters were ICP source power, RIE chuck power, chamber pressure and $BCl_3$/Ar gas composition. It was found that increase of ICP source power and RIE chuck power raised etch rate of InP, while that of chamber pressure decreased etch rate. Etched InP surface was clean and smooth (RMS roughness < 2 nm) with a moderate etch rate ($300\;{\sim}\;500\;{\AA}/min$) after the planar $BCl_3/Ar$ ICP etching. It may make it possible to open a new regime of InP etching with $CH_4/H_2$ - free plasma chemistry. Some amount of Ar addition (< 50%) also improved etch rates of InP, while too much Ar addition reduced etch rates of InP.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 하계종합학술대회 논문집
• /
• pp.922-925
• /
• 1999

The Silylation photo-resist etch process was tested by Enhanced-ICP dry etcher. The comparison of the two process results of micro pattern etching with 0.25${\mu}{\textrm}{m}$ CD by E-ICP and ICP reveals that E-ICP has better quality than ICP The etch rate and the microloading effect was improved in E-ICP Especially, the problem of the lateral etch was improved in E-ICP.

• 청정기술
• /
• 제9권3호
• /
• pp.101-105
• /
• 2003

MEMS(Micro Electro Mechanical System) 기술에서 실리콘 식각기술의 중요성으로 플라즈마 식각기술의 개발이 꾸준히 진행되고 있다. 본 연구에서는 ICP(Inductive Coupled Plasma)를 이용하여 플라즈마를 발생시켜, 이온에너지를 증가시키지 않고도 이온밀도를 높이고 이온입자들에 의한 식각의 방향성을 가할 수 있는 새로운 플라즈마 기술을 이용하였다. 이같이 플라즈마를 이용하여 실리콘웨이퍼를 식각하여 제조하는 MEMS 응용분야는 다양하나, 본 연구에서는 미생물배양에 응용할 수 있는 PCR(Polymerase Chain Reaction)장치 제작을 위한 식각에 이용하였다. Platen power, Coil power 및 Process pressure에 다양한 변화를 주어 각 변수에 따른 식각속도를 관찰하였다. 각 공정별 변수를 변화시킨 결과 Platen 12W, Coil power 500W, 식각/Passivation Cycle 6/7sec 일 경우 식각속도는 $1.2{\mu}m/min$ 이었고, sidewall profile은 $90{\pm}0.7^{\circ}$로 나타나 매우 우수한 결과를 보였다. 분 연구에 SF6를 식각에 이용하였으며 공정의 최적화를 통하여 사용량을 최소화하여환경영향이 최소가 될 수 있는 가능성이 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.65-66
• /
• 2005

Etching characteristics of $Ge_2Sb_2Te_5$ (GST) films were investigated using $Cl_2$/Ar inductively coupled plasma.We examined the etching characteristics such as etching rate and selectivity over oxide films of GST films using inductively coupled plasma (ICP) with various etching parameters such as $Cl_2$/Ar gas mixing ratios, ICP source power, pressure, and bias power. The maximum etch rate of GST film was $2,815{\AA}$/min and the selectivity higher than 12:1 over the oxide films was also obtained at the $Cl_2$ flow rates of 40 sccm.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.380-381
• /
• 2012

Bioinspired sea urchin-like structures were fabricated on silicon by inductively coupled plasma (ICP) etching using lens-like shape hexagonally patterned photoresist (PR) patterns and subsequent metal-assisted chemical etching (MaCE) [1]. The lens-like shape PR patterns with a diameter of 2 ${\mu}m$ were formed by conventional lithography method followed by thermal reflow process of PR patterns on a hotplate at $170^{\circ}C$ for 40 s. ICP etching process was carried out in an SF6 plasma ambient using an optimum etching conditions such as radio-frequency power of 50 W, ICP power of 25 W, SF6 flow rate of 30 sccm, process pressure of 10 mTorr, and etching time of 150 s in order to produce micron structure with tapered etch profile. 15 nm thick Ag film was evaporated on the samples using e-beam evaporator with a deposition rate of 0.05 nm/s. To form Ag nanoparticles (NPs), the samples were thermally treated (thermally dewetted) in a rapid thermal annealing system at $500^{\circ}C$ for 1 min in a nitrogen environment. The Ag thickness and thermal dewetting conditions were carefully chosen to obtain isolated Ag NPs. To fabricate needle-like nanostructures on both the micron structure (i.e., sea urchin-like structures) and flat surface of silicon, MaCE process, which is based on the strong catalytic activity of metal, was performed in a chemical etchant (HNO3: HF: H2O = 4: 1: 20) using Ag NPs at room temperature for 1 min. Finally, the residual Ag NPs were removed by immersion in a HNO3 solution. The fabricated structures after each process steps are shown in figure 1. It is well-known that the hierarchical micro- and nanostructures have efficient light harvesting properties [2-3]. Therefore, this fabrication technique for production of sea urchin-like structures is applicable to improve the performance of light harvesting devices.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 유기절연재료 방전 플라즈마연구회
• /
• pp.77-80
• /
• 2003

MEMS(Micro Electro Mechanical System) 기술에서 실리콘 식각기술의 중요성으로 플라즈마 식각기술의 개발이 꾸준히 진행되고 있다. 이중에서 ICP(Inductive Coupled Plasma)는 기존의 증착장치에 유도결합식 플라즈마를 추가로 발생시켜 증착막의 특성을 획기적으로 개선시키는 가장 최근에 개발된 기술이며, 이용에너지를 증가시키지 않고도 이용밀도를 높이고 이용업자들에 방향성을 가할 수 있는 새로운 플라즈마 기술로, 주로 MEMS 제조공정에 응용되고 있다. 본 연구에서는 STS-ICP $ASE^{HR}$을 이용하여 식각과 증착공정을 반복하여 식각을 하는 Bosch 식각에 관하여 연구하였다 STS-ICP $ASE^{HR}$ 장비의 Platen power, Coil power 및 Process pressure에 다양한 변화를 주어 각 변수에 따른 식각속도를 관찰하였다. 각 공정별 변수를 변화시킨 결과 Platen power 12W, Coil power 500W, 식각/Passivation Cycle 6/7sec 일 경우 식각속도는 $1.2{\mu}m$/min 이었고, Sidewall profile은 $90{\pm}0.7^{\circ}$로 나타나 매우 우수한 결과를 보였다.

• 한국결정성장학회지
• /
• 제26권4호
• /
• pp.145-149
• /
• 2016

플라즈마 조성, ICP source power, rf chuck power 등의 공정변수가 GaN epitaxy층의 식각특성에 미치는 영향을 조사하였다. $GaF_x$ 화합물 보다 더 높은 휘발성을 가지는 $GaCl_x$ 식각 생성물 형성이 가능한 $Cl_2/Ar$ 플라즈마가 $SF_6/Ar$ 플라즈마보다 더 높은 식각속도를 나타내었다. 또한, $Cl_2/Ar$ 플라즈마에서 Ar 비중이 증가함에 따라 물리적 식각 기구 활성화로 인해 식각 이방성이 향상됨을 확인하였다. 두 가지 플라즈마 조성 모두에서 ICP source power와 rf chuck power가 증가함에 따라 식각속도가 지속적으로 증가함을 확인하였고, $13Cl_2/2Ar$, 750W ICP power, 400 W rf chuck power, 10 mTorr 조건에서 최고 251.9 nm/min의 식각속도를 확보하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 추계종합학술대회 논문집
• /
• pp.887-890
• /
• 1999

The etch characteristics of E-ICP and ICP are compared for the improvement of SiO$_2$ etch Process. Etch rate and etch pattern profile are measured by $\alpha$ -step surface profiler and SEM, respectively. The E-ICP provides improved characteristics on etch rate and surface profile in comparison to ICP process.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.276-278
• /
• 1997

The reliable etching process is one of the essential steps in fabricating GaN based-device. High etch rate is needed to obtain a deeply etched structure and perfect anisotropic etched facet is needed to obtain lasing profile. In the research, therefore, we had proposed a planar inductively coupled plasma etcher (Planar ICP Etcher) as a high density plasma source, and studied the etching mechanism using the $CH_4/H_2$/Ar gas mixture. Dry etching characteristics such as etch rate, anisotropic etching profile and so on, for the III-V nitride layers were investigated using Planar ICP Etcher, based on the plasma characteristic as a variation of plasma process parameters.

• 반도체디스플레이기술학회지
• /
• 제20권3호
• /
• pp.32-38
• /
• 2021

We developed an inductively coupled plasma (ICP) etcher for GaN etching using a parallel plasma electrode source with a multifunctional chuck matched to it in order for the low power consumption and low process cost in comparison with the conventional ICP system with a helical-type plasma electrode source. The optimization process condition using it for the micro light-emitting diode (µ-LED) chip fabrication was established, which is an ICP RF power of 300 W, a chuck power of 200 W, a BCl₃/Cl₂ gas ratio of 3:2. Under this condition, the mesa structure with the etch depth over 1 ㎛ and the etch angle over 75° and also with no etching residue was obtained for the µ-LED chip. The developed ICP showed the improved values on the process pressure, the etch selectivity, the etch depth uniformity, the etch angle profile and the substrate temperature uniformity in comparison with the commercial ICP. The µ-LED chip fabricated using the developed ICP showed the similar or improved characteristics in the L-I-V measurements compared with the one fabricated using the conventional ICP method