• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1229-1230
• /
• 2006

This study is for implementation of PC based Motor fault diagnosis system. By using harmonics and current signals of the motor, this system diagnoses the motor condition by accumulated harmonic contribution rate. In this proposed system that was composed of 5 parts. A sensor, connection box, evaluation board, device server, and main computer are those. There were two types of sensor, one was harmonic sensor the other was current sensors. The signal was acquired by sensor, and transferred to evaluation board. Second one is connection box. Because the output type of sensor and input type of evaluation board is different, connection box was necessary. Third one was evaluation board. The signal from the sensor was converted to digital signal in evaluation board. And this signal was transferred to device server. Fourth one was device server. Device server transferred the data from evaluation board to main computer. And the last one was other parts controlled by main computer in main computer, there were communication and diagnosis algorithms. The result was derived by main computer. In the result, there were 12 categories and 5 levels of motor conditions. The proposed system had some advantages comparing with stand alone type commercial motor fault diagnosis system. The first, by using remote access it was easier to get the conditions of motor. The second, there was no need to handle the sensors when users measured the motor signals. By this property, no one was necessary at motor location site. The third, this system was less restricted by times and places than commercial stand alone type diagnosis system. Therefore users can operate this system only using the main computer. Once the sensors are installed at the motor, users doesn't need to move to check up the condition of motors. Moreover, if there is ethernet hub, many motors can be not only diagnosed at once but also decreased its cost.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1689-1690
• /
• 2006

This study is for implementation of PC based Motor fault diagnosis system. By using harmonics and current signals of the motor, this system diagnoses the motor condition by accumulated harmonic contribution rate. In this proposed system that was composed of 5 parts. A sensor, connection box, evaluation board, device server, and main computer are those. There were two types of sensor, one was harmonic sensor the other was current sensors. The signal was acquired by sensor, and transferred to evaluation board. Second one is connection box. Because the output type of sensor and input type of evaluation board is different, connection box was necessary. Third one was evaluation board. The signal from the sensor was converted to digital signal in evaluation board. And this signal was transferred to device server. Fourth one was device server Device server transferred the data from evaluation board to main computer. And the last one was other parts controlled by main computer. In main computer, there were communication and diagnosis algorithms. The result was derived by main computer. In the result, there were 12 categories and 5 levels of motor conditions. The proposed system had some advantages comparing with stand alone type commercial motor fault diagnosis system. The first, by using remote access it was easier to get the conditions of motor. The second, there was no need to handle the sensors when users measured the motor signals. By this property, no one was necessary at motor location site. The third, this system was less restricted by times and places than commercial stand alone type diagnosis system. Therefore users can operate this system only using the main computer. Once the sensors are installed at the motor, users doesn't need to move to check up the condition of motors. Moreover, if there is ethernet hub, many motors can be not only diagnosed at once but also decreased its cost.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2014년도 전력전자학술대회 논문집
• /
• pp.245-246
• /
• 2014

본 논문에서는 외전형 영구자석 동기 전동기의 전기적 브레이크 동작 시에 발생하는 회생 에너지를 분석한다. 그리고 전류 정보 없이 전동기 속도 및 배터리의 전압만으로 회생 전력을 제어하는 방법을 제안한다. 후륜 허브 전동기를 가지는 자전거 프로토 타입을 제작하고, 제안하는 회생 제동 제어 기법을 적용한 실험을 통해 제안 기법을 검증한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.280-284
• /
• 1997

In this paper, Nonlinear VSS control based on bang-bang control concept is derived under the assumption that the control input is bounded. We try to derive control algorithm which has almost same performance as the time optimal control. We focus this control scheme on the real implementation of DC motor position controller of flexible link, i.e. we obtain the switching curves from the real data of DC motor system operating under the full maximum and minimum applied voltages. State space is separated into several regions and we set different switching surfaces in each region to reduce chattering problem. The efficiency of the proposed controller is compared with PID controller and it is shown that the controller converges fast than PID controller without chattering. The hybrid controller scheme is also proposed not only to control the position of hub but also to reduce the vibration of end tip of flexible link.

• 대한기계학회논문집
• /
• 제19권6호
• /
• pp.1371-1381
• /
• 1995

A novel hybrid control scheme to actively control the endpoint position of a very flexible single-link manipulator is proposed. The control scheme consists of a motor mounted at the beam hub and a piezofilm actuator bonded to the surface of the flexible link. The control torque of the motor to produce a desired motion is firstly determined by employing the sliding mode control theory on the equation of motion of the rigid link having the same mass as that of the proposed flexible link. The torque is then applied to the flexible manipulator in order to activate the commanded motion. During the motion, undesirable oscillation is actively suppressed by applying a feedback control voltage to the piezofilm actuator. Consequently, the imposed desired position is accomplished. In order to demonstrate high control performances accrued from the proposed method, computer simulations are undertaken by treating both regulating and tracking control problems.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.6-8
• /
• 2008

In this paper a novel bearingless switched reluctance motor (SRM) with hybrid stator poles is proposed. The operating principle of proposed motor is also presented. Compared with existing bearingless SRM, it has many advantages such as lower number of switches and cost, simpler control algorithm, lower thermal load. Meanwhile through finite element method (FEM) characteristics of proposed structure such as inductance, torque and radial force can be obtained. According to the FEM results, the above advantages of the proposed structure can be verified.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.865_866
• /
• 2009

In this paper, a novel structure Bearingless SRM with hybrid stator poles is proposed. The motor torque can be controlled independently from radial force control. Analytical models of torque and radial force for proposed structure are explained. Based on these models, control scheme of desired radial force is proposed. In this control method, the magnitude of force can be controlled in arbitrary direction and magnitude by selecting some combinations of radial force windings. The validities of structure and control method are verified by the experimental results when motor is at standstill and running.

• 소음진동
• /
• 제6권2호
• /
• pp.187-196
• /
• 1996

A new control strategy to actively control the vibration of a very flexible single link manipulator is proposed and experimentally realized. The control scheme consists of two actuators; a motor mounted at the beam hub and a piezoceramic bonded to the surface of the flexible link. The control torque of the motor to produce a desired angular motion is firstly determined by employing a sliding mode control theory on the equivalent rigid dynamics. The torque is then applied to the flexible manipulator in order to activate the commanded motion. During the motion, underirable oscillation is actively suppressed by applying a feedback control voltage to the piezoceramic actuator. Consequently, the desired tip position is favorably accomplished without vibration. Measured control responses are presented in order to demonstrate the efficiency of the proposed control methodology.

• 한국지능시스템학회논문지
• /
• 제25권4호
• /
• pp.405-411
• /
• 2015

본 논문은 회전 동력을 직접 바퀴에 전달하는 휠-인 직구동 모터를 제어 대상으로 하여 속도 계측 및 제어시스템을 설계하는 방법에 대한 논문이다. 지능 제어기로서 16비트급 모션제어 전용의 dsPIC30F2010 마이크로프로세서를 사용한다. 프로세서의 여러 기능 중 내부의 최소 기능인 시스템 클럭, PWM, I/O, Timer 및 통신만을 사용하였고, 홀 신호 계측 및 제어 소프트웨어 기능에 대한 동작 특성을 시험하였다. 또한 이러한 기능을 이용하여 PDFF 속도제어 프로그램을 구현하고, 그 실험 결과를 보인다.

• 한국산학기술학회논문지
• /
• 제22권3호
• /
• pp.199-207
• /
• 2021

본 연구는 한국형고속철도(KTX)의 제동장치의 국산화를 통한 성능 개선을 위한 목적으로 수행되었다. 본 연구에서 기존 수입에 의존하고 있는 고속철도용 제동 디스크 허브를 국산화하기 위하여 유한요소 해석을 통해 성능을 분석하고 제동 시험결과와 상관도 분석을 통해 모델의 검증을 수행하였다. 또한, 제동시 발생할 수 있는 기계적인 특성을 검토하기 위하여 마찰열에 의한 열전달-열응력 해석, 고유진동해석 및 강도해석을 수행하였다. 디스크 허브 국산화 신규 모델의 개발을 위해 형상에 따른 설계 인자를 도출하고 파라미터 해석을 수행하여 방열성능을 향상시키고 경량화를 위한 최적 사양을 도출하고자 하였다. 개발 모델을 기존 모델과 비교한 결과 기존 모델 대비 제동시 발생하는 허브의 최고 온도가 낮아졌으며, 냉각 효율이 향상되었음 확인할 수 있었다. 또한, 고유진동수 및 강도 특성 또한 동등 수준 이상의 성능을 확보한 설계임을 확인하였다. 본 연구 결과는 철도차량 및 수송기기 분야의 제동 디스크 시스템 개발에 활용될 수 있을 것으로 기대된다.