• 한국결정성장학회지
• /
• 제11권3호
• /
• pp.115-119
• /
• 2001

수산화아피타이트와 이트리아 부분 안정화된 지르코니아의 바를 달리하는 3층 구조를 가즌ㄴ 생체 재료용 경사기능재료(FGMs)를 spark plasma sintering(SPS)과 hot pressing(HP) 장비로 제조하였다. HAp 원료에 대한 전처리를 실시할 경우 HAp의 소결성이 개선되었다. 전처리하여 얻은 FGM 복합체의 최고밀도는 전처리하지 않은 FGM 보다 낮은 온도에서 얻을 수 있었다. SPS로 FGM 소결체를 제조할 경우 10 MPa의 가압조건에서 8분 동안 소결 할 경우, $1200^{\circ}C$의 온도에서도 HAp의 TCP로의 분해 반응은 일어나지 않았으나. 이 온도에서 FGm의 지르코니아는 정방정에서 압방정으로와 상변화가 일어났다. 지르코니아 첨가에 따라. 즉 지르코니아의 응력 유기 상전이에 의해, HAp-ZrO$_2$ FGm 소결체의 기계적 물성이 증진된 것으로 예산된다. 치밀하고 고강도의 FGM을 제조하는 방법으로서 SPS가 HP공정에 비해 우수한 것으로 나타났다.

• 한국재료학회지
• /
• 제32권3호
• /
• pp.132-138
• /
• 2022

Zintl phase Mg₃Sb₂ is a promising thermoelectric material in medium to high temperature range due to its low band gap energy and characteristic electron-crystal phonon-glass behavior. P-type Mg₃Sb₂ has conventionally exhibited lower thermoelectric properties compared to its n-type counterparts, which have poor electrical conductivity. To address these problems, a small amount of Sn doping was considered in this alloy system. P-type Mg₃Sb₂ was synthesized by controlled melting, pulverizing, and subsequent vacuum hot pressing (VHP) method. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to investigate phases and microstructure development during the process. Single phase Mg₃Sb₂ was successfully formed when 16 at.% of Mg was excessively added to the system. Nominal compositions of Mg_3.8Sb_2-xSn_x (0 ≤ x ≤ 0.008) were considered in this study. Thermoelectric properties were evaluated in terms of Seebeck coefficient, electrical conductivity, and thermal conductivity. A peak ZT value ≈ 0.32 was found for the specimen Mg_3.8Sb_1.994Sn_0.006 at 873 K, showing an improved ZT value compared to intrinsic one. Transport properties were also evaluated and discussed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.289-292
• /
• 2001

Aluminium foams, having a closed cell structure, fabricated by applying the powder compact method and an induction heating were studied. The powdered A6061 mixed with the powdered titanium hydride as a foaming agent was hot pressed into a foamable precursor. The resulting precursor was foamed by induction heating up to desired temperature. The effects of the titanium hydride content ($0.3{\~}1.5 wt.\%$), pressing pressure of the foamable precursor material (50-150kN), the forming temperature ($610{\~}690^{\circ}C$) and heating rate during foaming on the expansion behavior of the foam were investigated.

• 한국세라믹학회지
• /
• 제29권7호
• /
• pp.577-585
• /
• 1992

TiB2 and TiC were prepared from the mixture of metal titanium, boron and graphite powders in Argon atmosphere by Self-propagating High-temperature Synthesis method. The sintered properties of TiB2-TiC composite as a function of TiC content and sintering temperature were investigated in TiB2 matrix. The sintered properties were the most excellent at 10 wt% TiC content in TiB2-TiC composite. The relative density, M.O.R strength, hardness and fracture toughness of TiB2-10 wt% TiC composite sintered at 190$0^{\circ}C$ for 90 min by hot-pressing under the pressure of 30 MPa were 98.6%, 634 MPa, 2128.1 kg/$\textrm{mm}^2$ and 4.09 MN/m3/2, respectively.

• Tribology and Lubricants
• /
• 제18권2호
• /
• pp.127-132
• /
• 2002

The Taguchi method, a robust experimental design, was used to optimize manufacturing parameters of a brake lining during hot pressing and heat treatment. A friction material containing 15 ingredients was employed fur this experiment and friction and wear tests were carried out by using a pad-on-disk type tribotester. Sixteen brake linings with different manufacturing conditions were examined according to a parameter design. From the results of the signal-to-noise (S/N) ratio and the analysis of variance (ANOVA), the cause and effect of the manufacturing parameters on physical properties (hardness and porosity) and friction and wear characteristics of brake linings was obtained.

• 한국세라믹학회지
• /
• 제32권9호
• /
• pp.1009-1018
• /
• 1995

(Ti.Si)C composite powders were synthesized by SHS method using microwave energy. Compositional and structural characterization of the powder were carried out by using scanning electron microscopy and X-ray diffraction. The average particle size of the synthesized (Ti.Si)C composite powders was smaller than that of the starting materials. From the results of the temperature profile, combustion temperature and velocity were decreased with increasing Si molar ratio. With increasing C molar ratio combustion temperature and velocity did not change. (Ti.Si)C composite was sintered at 185$0^{\circ}C$ for 60 min by using hot-pressing with 30 MPa. The best properties were obtained from the sintered specimen whose composition was 1 : 1 : 1.9 molar ratio of Ti : Si : C. The sintering density, flexural strength and vickers hardness of the sintered body were 4.71 g/㎤, 423 MPa and 21 GPa, respectively.

• 한국세라믹학회지
• /
• 제34권7호
• /
• pp.731-737
• /
• 1997

TixZr1-xC(0$0^{\circ}C$, 5.1 mm/sec respectively. The relative density, three point flexural strength, and the hardness of composites, which was sintered at 190$0^{\circ}C$ for 60 min by using hot-pressing under a pressure of 30 MPa, were 99%, 525 MPa and 24 GPa respectively.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.69-72
• /
• 2002

The high temperature deformation behavior of SiCp/2124Al composite and 2124Al alloy was investigated by hot compression test in a temperature ranged $400~475^{\circ}C$ over a strain rate ranged $10^{-3}~1s^{-1}$. The billets of 2124Al alloy and SiCp/2124Al composite were fabricated by vacuum hot pressing process. The stress-strain curve during high temperature deformation exhibited a peak stress, and then the flow stress decreased gradually into a steady state stress with increasing the strain. It was found that the flow-softening behavior was attributed to the dynamic recovery, local dynamic recrystallization and dynamic precipitation during the deformation. The precipitation phases were identified as S' and S by TEM diffraction pattern. Base on the TEM inspection, the relationship between the Z-H parameter and subgrain size was found based on the experiment data. The dependence of flow stress on temperature and strain rate could be formulated well by a hyperbolic-sinusoidal relationship using the Zener-Hollomon parameter.

• 한국세라믹학회지
• /
• 제34권11호
• /
• pp.1129-1138
• /
• 1997

Al2O3/20 vol%YAG composite containing equiaxed grains and Al2O3/20 vol%LaAl11O18 composite containing elongated grains were fabricated using Al2O3-Y2O3 composition and Al2O3-La2O3 composition, respectively, by hot-pressing. In order to investigate the influence of microstructural control of second phase on toughening effect of toughened ceramic composites, AE (acoustic emission) measurements have been coupled with fracture toughness experiments(SENB and SEPB method). A separation of the fracture toughness and analysis of toughening mechanism was possible using the AE technique. The fracture toughness of hot-pressed materials was estimated to be 3.2 MPam0.5 for monolithic alumina, 4.7 MPam0.5 for Al2O3/20 vol%YAG composite and 6.2 MPam0.5 for Al2O3/20 vol%LaAl11O18 composite. In monolithic Al2O3, toughening does not occur as a result of either microcracking or grain bridging, whereas, composites exhibit toughening effects by both microcracking in the frontal zone and gain bridging in the wake zone, resulting in an improvement of fracture toughness as compared with monolithic Al2O3. The fracture toughness of Al2O3/20 vol%LaAl11O18 composite is higher than that of Al2O3/20 vol%YAG composite. It may be attributed to the elongated microstructure of Al2O3/20 vol%LaAl11O18 composite, resulting relatively greater bridging effect.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.447-451
• /
• 2009

Continuous SiC fiber-reinforced SiC composites ($SiC_f$/SiC) were fabricated by electrophoretic deposition (EPD). Nine types of slurries with different powder contents, binder resin amounts and slurry pH were deposited on Tyranno$^{TM}$-SA fabrics by EPD at 135 V for ten minutes to determine the optimal conditions. Further EPD using the optimum slurry conditions was performed on fabrics with four different pyrolitic carbon (PyC) thicknesses. The density of the hot-pressed composites decreased with increasing PyC thickness due to the difficulty of infiltrating the slurry into the narrow gaps between the fibers. On the other hand, the mechanical strength increased with increasing PyC thickness despite the decrease in density, which was explained by the enhanced crack deflection with increasing PyC thickness. The $SiC_f$/SiC composites showed the highest density and flexural strength of 94% and 342 MPa, respectively, showing EPD as a feasible method for dense $SiC_f$/SiC fabrication.