• 대한조선학회논문집
• /
• 제41권5호
• /
• pp.28-33
• /
• 2004

Generally Horn-type rudders have been used for single propeller and single rudder system. The reason is that the rudder torques of Horn-type rudder are smaller than those of Spade rudder with same lift force. But it is found that the rudder cavitation occurs on a Horn-type rudder of fast container ship. In this paper the comparison results of Horn-type and Spade rudders are described. HPMM tests are carried out to compare the effects of two rudder types on the maneuverability of a ship. It is shown that the maneuvering performance of a ship equipped with Horn-type rudder is better than that equipped with Spade rudder by comparing the test results and maneuvering coefficients at scantling condition. The reason is that the movable part area of Horn-type rudder is about 14％ larger than that of Spade rudder with same total area. And the rudder torque of Spade rudder is greater than that of Horn rudder. At ballast condition, however, the effect of rudder type is negligible.

• 대한조선학회논문집
• /
• 제48권4호
• /
• pp.346-356
• /
• 2011

Rudder is to be located in extremely complicated flows generated and disturbed behind a hull and a propeller in operation. In order to estimate the rudder efficiency, it is quite important to investigate the disturbed flows due to the interaction under the hull-propeller and rudder condition. The purpose of the present research is to investigate the interaction between the hull-propeller and a high-lifting horn-type rudder through both numerical computations and experiments. A horn-type rudder implementing the Coanda effect of USB (Upper Surface Blowing) type is selected for its high efficiency of lifting force, and a 1/85 scaled model of 47K PC(Product Carrier) is manufactured for the purpose of the model test. The forces acting on the rudder during the experiment are measured using a three-component force gauge. Both cases are investigated in the hull-propeller-rudder condition and rudder open-water condition, which confirms that the flows generated under the former condition is considerably different from that of the latter condition.

• 대한조선학회논문집
• /
• 제44권2호
• /
• pp.101-110
• /
• 2007

Recently, rudder erosion due to cavitation frequently has occurred at large high speed container carriers. Especially, in the case of a horn-type rudder, the rudder erosion is severe around a gap. The gap-flow characteristics are investigated through a computational method to understand the effects of a gap on the cavitation and rudder efficiency. A viscous flow theory utilizing a cavitation model is applied to calculate the flow around idealized 2-dimensional rudder sections in a full scale. The effects of gap clearance and flow-control projection are also investigated. From the computational results, the mass flow rate through a gap is found to be one of the important parameters to affect the cavitation and rudder efficiency.

• 한국해양환경ㆍ에너지학회지
• /
• 제4권1호
• /
• pp.70-74
• /
• 2001

본 논문에서는 특수타를 채용한 선박과 일반타를 장착한 선박에 대하여 구속모형시험을 통하여 비교 연구를 실시하였다. 구속모형시험은 일반타가 장착된 경우와 특수타가 장착된 경우에 대하여 수행되었고, 조종수학 모델링은 Abkowitz 수학 모델을 통하여 유체력 미계수를 구하여 조종운동을 시뮬레이션하였다. 연구 결과에 의하면 플랩(Flap) 타를 채택한 경우에 선회성능은 아주 향상되는 것을 확인하였다.

• 대한조선학회논문집
• /
• 제47권4호
• /
• pp.553-564
• /
• 2010

This paper studies on the rudder shapes for the suppression of the cavitation around a horn-type rudder. To improve the problems due to cavitation, there have been several studies. However, these some studies are recognized as incomplete ways to suppress the rudder cavitation. In this study, the section shapes to suppress the cavitation phenomena are determined by moving the location of maximum thickness for reducing the curvature variation and changing the radius of leading edge. Also, in the pintle part, the curvature radius of the inlet outlet edge of rudder plate is changed. During the design of rudder shape, two-dimensional numerical simulations are firstly performed because those offer some advantages with that cavitation phenomena becomes predictable for a short time, and then the three-dimensional numerical simulations are performed to confirm the determination. The time mean distribution of the propeller slipstream is imposed on the inlet boundary condition. As some results, this paper shows the effects reducing the range of the occurrence of cavitation, and suggests the references on the design of a horn-type rudder for the suppression of cavitation phenomena.

• 대한기계학회논문집B
• /
• 제33권11호
• /
• pp.924-931
• /
• 2009

The two-dimensional turbulent flow around the horn-type rudder has been examined in the present study by using the commercial code FLUENT. The standard ${\kappa}-{\epsilon}$ model is used as a closure relationship. The geometry of horn rudder is based on the NACA 0020 airfoil. The simulations for various angle attack (${\alpha}$) and yaw angle(${\delta}$) are carried out. The effect of Reynolds number is also investigated in this study. The cavitation is more possible when the yaw angle is $6^{\circ}$ and it is more serious as Reynolds number increases.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권2호
• /
• pp.177-184
• /
• 2017

The Coanda effect is the phenomenon of a fluid jet to stay attached to a curved surface; when a jet stream is applied tangentially to a convex surface, lift force is generated by increase in the circulation. The Coanda effect has great potential to be applied practically applied to marine hydrodynamics where various lifting surfaces are being widely used to control the behavior of ships and offshore structures. In the present study, Numerical simulations and corresponding experiments were performed to ascertain the applicability of the Coanda effect to a horn-type rudder. It was found that the Coanda jet increases the lift coefficient of the rudder by as much as 52% at a jet momentum coefficient of 0.1 and rudder angle of $10^{\circ}$.

• 대한조선학회논문집
• /
• 제44권3호
• /
• pp.228-237
• /
• 2007

The flow characteristics around a horn-type rudder behind an operating propeller of a high-speed large container carrier are studied through a numerical method in fully wetted and cavitating flow conditions. The computations are carried out in a small scale ratio of 10.00(gap space=5mm) to consider the gap effects. The Reynolds averaged Navier-Stokes equation for a mixed fluid and vapor transport equation applying cavitation model are solved. The axisymmetry body-force distribution technique is utilized to simulate the flow behind an operating propeller. The gap flow, the three-dimensional flow separation, and the cavitation are the flow characteristics of a horn-type rudder. The pattern of three-dimensional flow separation is analyzed utilizing a topological rule. The various cavity positions predicted by CFD were shown to be very similar to rudder erosion positions in real ship rudder. The effect of a preventing cavitation device, a horizontal guide plate, is also investigated.

• 대한조선학회논문집
• /
• 제46권6호
• /
• pp.578-586
• /
• 2009

Recently, horn-type rudders are generally being used at high speed container ships and are frequently suffering from the cavitation occurs on the rudder surface in the vicinity of the gap between the horn and rudder plate. In the present study, a fluid supplying device is employed as to decrease the gap cavitation of the horn-type rudder. The device is devised to inject the water against the pressure side through the nozzle installed inside of the gap to control the gap flow. Numerical calculations are performed to investigate the effectiveness of the device and the results show that the device can noticeably reduce the gap cavitation. The rates of water injection for achievement of the maximum retardations of gap flow are also sought.

• 대한조선학회논문집
• /
• 제47권4호
• /
• pp.543-552
• /
• 2010

The Coanda effect is noticeable when a jet stream is applied tangential to a curved surface since then the jet stream remains attached to the surface beyond the point where flow separates otherwise and results in augmentation of circulation and lift. Numerous experimental and numerical studies have been performed in various fields of aerodynamics to exploit the Coanda effect and many of them found to be useful. It can be speculated that the Coanda effect may have practical application to the field of marine hydrodynamics as well since various control surfaces are being used to control behaviors of ships and offshore structures. In the present study, the Coanda effect has been applied to a horn type rudder and a series of numerical computations and model experiments are performed to find the practical applicability. The results indicate that the Coanda jet increases the lift coefficient of the rudder as much as 52% at the momentum coefficient $C_j$ = 0.1 and the rudder angle ${\alpha}=10^{\circ}$.