• Journal of Broadcast Engineering
• /
• v.16 no.3
• /
• pp.448-461
• /
• 2011

H.264/AVC significantly outperforms the previous video coding standards with many new coding tools. Among these tools, several intra-block coding tools can particularly improve coding efficiency. For intra prediction, H.264/AVC supports most probable mode in the entropy coding process to reduce syntax elements indicating intra prediction modes and most probable mode selection ratio is very high. Also, in general, natural images and videos have many homogeneous regions whose high correlation with neighbouring blocks. In this paper, we propose intra prediction mode SKIP mode using decoder-side prediction to improve the coding efficiency. The proposed method is determined the optimal prediction mode using only neighbouring block's information and coded on the basis of the conventional prediction/transform coding. And the prediction modes are not send to decoder at all. Skipped intra prediction mode is determined by decoder. Experimental results show that the proposed method achieves coding gains of 1.40% for common intermediate format(CIF), 3.24% for 720p sequences against the H.264/AVC JM 17.0 reference software.

• Membrane Journal
• /
• v.3 no.2
• /
• pp.79-82
• /
• 1993

The sorption equilibria and permeabilities for $CO_2$ in a homogeneous membrane of polystyrene with the glass transition temperature of $95^{\circ}C$ were measured at a temperature of $60^{\circ}C$ and gas pressures up to 1.6 MPa and 2.5 MPa, respectively. The sorption isotherm had the form af dual-mode sorption model at low gas pressures, but became linear at pressures above 1.3 MPa. The linear portion of the isotherm extrapolated to the origin. The pressure dependence of the rnean permeability coefficient deviated upward from the dualsrhode mobility model prediction. It was found that the glass transition was brought out by the plasticization action of sotbed $CO_2$ at a gas pressure of 1.3 MPa from the sorption isotherm. And this result was consistent with an increase in the mean permeability coefficient with applied gas pressure.

• Computers and Concrete
• /
• v.12 no.5
• /
• pp.627-650
• /
• 2013

This paper deals with application of a non-linear continuum model for reinforced concrete affected by alkali-aggregate reaction (AAR) to analysis of some nuclear structures. The macroscopic behaviour of the material affected by AAR is described by incorporating a homogenization/averaging procedure. The formulation addresses the main stages of the deformation process, i.e., a homogeneous deformation mode as well as that involving localized deformation, associated with formation of macrocracks. The formulation is applied to examine the mechanical behaviour of some reinforced concrete structures in nuclear power facilities located in Quebec (Canada). First, a containment structure is analyzed subjected to 45 years of continuing AAR. Later, an inelastic analysis is carried out for the spent fuel pool taking into account the interaction with the adjacent jointed rock mass foundation. In the latter case, the structure is said to be subjected to continuing AAR that is followed by a seismic event.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1155-1158
• /
• 2004

Various inorganic alignment layers of nematic liquid crystal (NLC) molecules were investigated. Ar ion beam (IB) irradiation was utilized for alignment method and homogenous and homeotropic orientations with tilt angle were obtained on the suitable inorganic thin films. Proper doping materials were added to diamond-like carbon (DLC) films. In the case of homogeneous alignment, nitrogen doping affected the increase of pretilt angle, while the fluorine bonding in the DLC films was induced the tilted homeotropic alignment cause its extreme hydrophobic property. These results showed that ion beam irradiation method could be applied to the various alignment mode of NLC such as IPS, TN and MVA.

• Journal of Mechanical Science and Technology
• /
• v.18 no.8
• /
• pp.1375-1387
• /
• 2004

A solution is given for the elastodynamic problem of a crack perpendicular to the graded interfacial zone in bonded materials under the action of anti plane shear impact. The interfacial zone is modeled as a nonhomogeneous interlayer with the power-law variations of its shear modulus and mass density between the two dissimilar, homogeneous half-planes. Laplace and Fourier integral transforms are employed to reduce the transient problem to the solution of a Cauchy-type singular integral equation in the Laplace transform domain. Via the numerical inversion of the Laplace transforms, the values of the dynamic stress intensity factors are obtained as a function of time. As a result, the influences of material and geometric parameters of the bonded media on the overshoot characteristics of the dynamic stress intensities are discussed. A comparison is also made with the corresponding elastostatic solutions, addressing the inertia effect on the dynamic load transfer to the crack tips for various combinations of the physical properties.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.4 no.3
• /
• pp.39-47
• /
• 1995

This paper suggests generalize mathematica mode for the benefit of volumetric error analysis of a multi-axis machine tool machining a sculptured surfaces. The volumetric error, in this paper, is defined as a three dimensional error at the cutting point, which is caused by the geometric errors and the kinematic errors of each axis and alignment errors of the cutting tool. The actual cutting position is analyzed based on the form shaping model including a geometric error of the moving carriage, where a form shaping model is derived from the homogeneous transformation matrix. Then the volumetric error is obtained by calculating the position difference between the actual cutting position and the ideal one calculated from a Nonuniform Rational B-Spline named as NURES. The simulation study shows the effectiveness for predicting the behavior of machining error and for the method of error compensation.

• International Journal of Automotive Technology
• /
• v.6 no.3
• /
• pp.293-303
• /
• 2005

Bonded dissimilar materials are being increasingly used in automobiles, aircraft, rolling stocks, electronic devices and engineering structures. Bonded dissimilar materials have several material advantages over homogeneous materials such as high strength, high reliability, light weight and vibration reduction. Due to their increased use it is necessary to understand how these materials behave under stress conditions. One important area is the analysis of the stress intensity factors for interface cracks emanating from circular holes in bonded dissimilar materials. In this study, the bonded scarf joint is selected for analysis using a model which has comprehensive mixed-mode components. The stress intensity factors were determined by using the boundary element method (BEM) on the interface cracks. Variations of scarf angles and crack lengths emanating from a centered circular hole and an edged semicircular hole in the Al/Epoxy bonded scarf joints of dissimilar materials are computed. From these results, the stress intensity factor calculations are verified. In addition, the relationship between scarf angle variation and the effect by crack length and holes are discussed.

• Tunnel and Underground Space
• /
• v.11 no.4
• /
• pp.339-343
• /
• 2001

Shield tunnel having circular section located in the soil or soft rock layer is liable to deform in such a way that its two diagonal diameters crossing each other expand and contract alternately during earthquakes. Based on this knowledge, the ground-tunnel interaction effect for this particular vibration mode is investigated. The ground surrounding a tunnel is assumed to be a homogeneous elastic medium. The bonded boundary condition on the ground-tunnel interface is considered. This suggests a firm bond between the ground and the tunnel lining. As Poisson's ratio and stiffness of the ground increases, the strain induced within the tunnel lining increases.

• Journal of KSNVE
• /
• v.5 no.3
• /
• pp.327-335
• /
• 1995

The study deals with the vibration of a beam whose flexural and centroidal axes are not coincident. The elementary bending-twisting theory is employed to derive the equation of motion, in which the effects of rotary inertia are added to the bending displacements and the effects of warping are added to the twist. Bending translation is restricted to one direction so that one bending equation is used instead of two. The equations of motion are solved by using the boundary value problem. The exact natural frequencies are fund from the frequency equation, which is obtained from the condition that the homogeneous system of algebraic equations representing the spatial solution shall not yield a trivial solution. The orthogonal conditions are established, and the principal mode equations of forced vibration are derived. As an example, the cantilevered beam is chosen and the first some natural frequencies and their modal shapes are found.

• Structural Engineering and Mechanics
• /
• v.35 no.2
• /
• pp.217-240
• /
• 2010

A semi-analytical method is presented for accurately prediction of the free vibration behavior of generally laminated composite plates with arbitrary boundary conditions. The method employs the technique of separation of spatial variables within Hamilton's principle to obtain the equations of motion, including two systems of coupled ordinary homogeneous differential equations. Subsequently, by applying the laminate constitutive relations into the resulting equations two sets of coupled ordinary differential equations with constant coefficients, in terms of displacements, are achieved. The obtained differential equations are solved for the natural frequencies and corresponding mode shapes, with the use of the exact state-space approach. The formulation is exploited in the framework of the first-order shear deformation theory to incorporate the effects of transverse shear deformation and rotary inertia. The efficiency and accuracy of the present method are demonstrated by obtaining solutions to a wide range of problems and comparing them with finite element analysis and previously published results.