• Bulletin of the Korean Chemical Society
• /
• 제26권10호
• /
• pp.1569-1574
• /
• 2005

To develop new hole-blocking materials for phosphorescent organic light-emitting diodes (PhOLEDs), 5,6-dihydro-2,9-diisopropyl-4,7-diphenyl[1,10]phenanthroline (1) and 5,6-dihydro-2,9-diisopropyl-4-(4-methoxyphenyl)-7-phenyl[1,10]phenanthroline (2) were synthesized. While the absorption spectrum of 1 is very similar to that of 2, the photoluminescence spectrum of 1 has the feature of the narrower and blue-shifted blueviolet emission at the peak of 356 nm compared to that of 2. The HOMO and LUMO energy levels of 1 and 2 were estimated from the measurement of cyclic voltammetry, and 1 has the appropriate levels for a holeblocking layer (HBL). The use of 1 as a HBL in a green PhOLED led to good efficiency of 23.6 cd/A at 4.4 mA/$cm^2$.

• 한국기계가공학회지
• /
• 제18권5호
• /
• pp.17-22
• /
• 2019

In this study, Cermet Reamers for planet carrier was manufactured and the machining characteristics were analyzed through processing experiment. Cermet reamer with ∅14, ∅15, ∅18, and ∅21mm was used and machining characteristics were compared and analyzed by observing tool wear, machining hole dimensions and surface roughness. In the flank wear of the tool, the result is less than 0.2mm, which is the target value for each tool size. The experimental results of the machining hole dimensions show the results of the process control range of 3/100 or less according to the size of the tool. Also, the surface roughness measurement result showed a value of less than $0.5{\mu}m$ in the process control range for each tool size. As a result of observing the experimental results of each ∅, the results satisfied the process standard in both the tool wear, the machining hole dimension and the surface roughness.

• 한국안전학회지
• /
• 제21권1호
• /
• pp.96-104
• /
• 2006

This study is to find out how the sawdust-mixed RC beam with holes acts compared to two case of normal one with sawdust without hole, without sawdust. variables are ED3H1, ED3H2, ED3H1UB, ED3H2L, ED5H1, ED5H1UB, ED5H2, ED5H2L, Normal with sawdust PLA without sawdust. All sand, aggregate, cement are in accordance with KS. mixing design is also in accordance with KS and done at D remicon company in order to decrease any error in mixing manually. ED3H1 showed 7tone of maximum load capacity having only minor tensile deformation around hole, compared to the center of the beam. ED5H2L showed almost same shape of tensile strain between hole area and center of two beam length, while having 9.5 tone load capacity, incase of two holes being in the longitudinal axis. But ED5H2 in case of two holes being in same forcing direction showed 8.4tone of load capacity while having minor tensile chape around hole and normal tensile shape in the center of beam length. Two diameter 3cm hole in longitudinal axis give more effective behavior than the other case, practically. Capacity decrease between 5cm and 3cm in eccentric position form the longitudinal axis is less than percents. There is minor capacity difference between hole diameter 3cm hole, but 13tone difference of load capacity between hole diameter 5cm.

• 대한조선학회논문집
• /
• 제32권1호
• /
• pp.17-24
• /
• 1995

본 연구에서는 범용 CAD 시스템을 사용하여 상세구조 설계단계에서의 자동화 가능성을 검토하였다. 파라메트릭 개념을 가진 macro의 기능이 유효함을 확인하였고, 이 개념을 이용하여 대표적인 구조부재인 transverse web frame, slot hole & collar plate 그리고 bracket의 설계에 적용하였다.

• 동력기계공학회지
• /
• 제10권3호
• /
• pp.67-72
• /
• 2006

The effect of manufacturing parameters on wear and improve cooling of motorcycle break system was studied using a disk-on-pad type friction tester. Such parameters conditions have an effect on the wear and improve cooling factor such as applied load, sliding speed, frictional time and number of ventilated disk hole. However, it is difficult to know the mutual relation of these factor. In this study, the wear and cooling characteristics using design of experiment containing 4 elements were investigated for an optimal condition for the best motorcycle disk break system employing Taguchi robust experimental design. From this study, the result was shown that vents have an effect on convection area improving more cooling ability and reduced wear of the disk.

• 소성∙가공
• /
• 제24권1호
• /
• pp.37-43
• /
• 2015

The purpose of the current study is to improve the clinching joint strength of aluminum and fiber metal laminates (FMLs) comprised of three layers. The joining of FML and Al 5052 by a conventional clinching joint has some disadvantages such as necking of the upper sheet, lack of interlocking, defects caused by the vertical load, and especially loss of strength of the composite material due to the low ductility. In the current study, a tapered-hole clinching method is proposed as an alternative for the joining of Al 5052 and FMLs. A hole with a tapered shape is formed before the joining process. The design parameters were evaluated using the Taguchi method for the geometry of the tapered hole in order to determine the maximum separation load. The diameter of the punch corner, clearance, punch stroke and the tapered length were used as the main variables in the Taguchi method. In conclusion, the contribution ratio for each of the fours variable examined was 35.07%, 22.44%, 21.32% and 14.11%, respectively. In addition, the appropriate combination of the design parameters can make a 5% improvement in the vertical direction joint strength.

• 한국재료학회지
• /
• 제3권2호
• /
• pp.197-204
• /
• 1993

Plastic기 복합재료의 파괴거동에 미치는 원공크기오 판폭의 영향을 검토하기 위하여 단축인장시험을 행하였다. 점응력파손조건에서의 특성길이 $d_o$는 원공크기 및 판폭에 의존하며, 이를 기초로 파손강도를 예측하기 위한 수정 점응력 파손조건식을 제안하였다. 이 파손조건의 예측값은 실험값과 잘 일치하였다. 파손 강도는 원공선단의 손상비의 증가에 따라 증가하며, 이는 손상영역의 형성으로 인한 응력완화현상으로 설명되어 진다. 또한 불안정 파괴시의 최대균열길이 $a_c$는 특성길이 $d_o$의 약 2배의 값을 나타낸다. 파괴인성에 대응하는 한계에너지해방율 $G_c$의 변화는 원공선단의 손상영역의 증가에 의한 응력완화가 주요한 원인이라고 할 수 있다.

• 한국항공우주학회지
• /
• 제49권7호
• /
• pp.549-555
• /
• 2021

원공이 있는 복합재 적층판의 강도는 복합재 항공기기 설계 시 충격하중이 가해지는 부위의 설계 허용치로 사용된다. 일반적으로 BVID (Barely Visible Impact Damage)에 의한 강도저하는 24.0 mm 폭의 시편에 6.0 mm 지름의 원공이 있는 시편의 강도로 가정한다. 본 연구에서는 원공이 있는 복합재 적층판의 강도에 적층각이 미치는 영향을 조사하기 위해 잔류강도 시험을 수행하였다. 원공이 있는 적층판의 강도를 예측하기 위해 특성길이를 이용한 점응력 파손기준을 사용하였고, 이론해를 검증하기 위하여 유한요소해석을 수행하였다. 실험결과로부터 특성길이는 0°, ±45°와 90°층의 비율과 관련이 있음을 보였다. 또한 회귀분석을 통하여 임의의 적층 패턴에 대한 특성길이와 원공이 없는 시편의 강도를 결정하였다.

• 대한기계학회논문집A
• /
• 제26권5호
• /
• pp.890-895
• /
• 2002

Cold expansion method is retarded of crack initiation due to the compressive residual stress developed on the hole surface. Previous research has just been study about residual stress distribution in the hole surrounding. But, The purpose of this study was to improve the understanding of the residual stress effect in hole surrounding as crack growth from another hole. In this paper, it is shown that residual stress is redistributed due to the application of cold expansion process for CT specimen using finite element method. It is further shown that tensile stress increases in proportion to cold expansion ratio in the vicinity of crack. It is thought that stress intensity factor increases with cold expansion ratio.

• 한국전산유체공학회지
• /
• 제15권1호
• /
• pp.56-63
• /
• 2010

Since emission regulations for vehicles have become more stringent, SCR technology has drawn a strong attention in order to reduce NOx emissions. Optimal design of a reductant injection nozzle and a multi-hole plate located between the cone and catalyst is critical in that the uniform distribution of reductant is necessary to maximize the NOx conversion efficiency and minimize the slip of reductant in SCR. In this work, an LPG fuel(C3H8 in vapor state) was used as a reductant for LPG vehicles. A Realizable k-$\varepsilon$ model is used for turbulence, and SCR body is defined as porous media with inertia and viscous resistances measured in this work. Effect of the number of nozzle holes on the flow mixing index was analyzed, which revealed that a four hole nozzle shows the best performance in terms of uniformity of flow. An installment of a multi-hole plate at the entrance of catalyst was evaluated with flow mixing index, uniformity of flow, and pressure drop. A multi-hole plate with gradual hole diameter change in three steps showed the best uniformity of flow within the conditions suggested in this work.