• 한국안전학회지
• /
• 제9권1호
• /
• pp.61-67
• /
• 1994

Rate of rise heat detectors that respond to the heat generated in fire plume and alarm when the temperature reaches a specified point, give a great influences to the loss of life and property according to their reaction sensitivity. In this study, simple equations were derived which can be predicted the response time and temperature of the rate of rise heat detector with the results of hot wind tunnel tests and compartment fire experiments.

• 열처리공학회지
• /
• 제25권5호
• /
• pp.239-243
• /
• 2012

$SnO_2$ thin films were prepared on the Si substrate by radio frequency (RF) magnetron sputtering and then post deposition vacuum annealed to investigate the effect of annealing temperature on the structural properties and hydrogen gas sensitivity of the films. The films that annealed at $300^{\circ}C$ show the higher sensitivity than the other films annealed at $150^{\circ}C$. From atomic force microscope observation, it is supposed that post deposition annealing promotes the rough surface and also, increase gas sensitivity of $SnO_2$ films for hydrogen gas. These results suggest that the vacuum annealed $SnO_2$ thin films at optimized temperatures are promising for practical high-performance hydrogen gas sensors.

• 대한기계학회논문집B
• /
• 제32권10호
• /
• pp.800-809
• /
• 2008

Scanning Thermal Microscope (SThM) is the tool that can map out temperature or the thermal property distribution with the highest spatial resolution. Since the local temperature or the thermal property of samples is measured from the extremely small heat transferred through the nanoscale tip-sample contact, improving the sensitivity of SThM probe has always been the key issue. In this study, we develop a new design and fabrication process of SThM probe to improve the sensitivity. The fabrication process is optimized so that cantilevers and tips are made of thermally grown silicon dioxide, which has the lowest thermal conductivity among the materials used in MEMS. The new design allows much higher tip so that heat transfer through the air gap between the sample-probe is reduced further. The position of a reflector is located as far away as possible to minimize the thermal perturbation due to the laser. These full $SiO_2$ SThM probes have much higher sensitivity than that of previous ones.

• 방사성폐기물학회지
• /
• 제21권3호
• /
• pp.359-370
• /
• 2023

The thermal integrity of spent nuclear fuels has to be maintained during their long-term dry storage. The detailed temperature distributions of spent fuel assemblies are essential for evaluating the integrity of their dry storage systems. In this study, a subchannel analysis model was developed for a canister of a single fuel assembly using the COBRA-SFS code. The thermal parameters affecting the peak cladding temperature (PCT) of the spent fuel assembly were identified, and sensitivity analyses were performed based on these parameters. The subchannel analysis results indicated the presence of a recirculation flow, based on natural convection, between the fuel assembly and downcomer region. The sensitivity analysis of the thermal parameters indicated that the PCT was affected by the emissivity of the fuel cladding and basket, convective heat transfer coefficient, and thermal conductivity of the fluid. However, the effects of the wall friction factor of the canister, form loss coefficient of the grid spacers, and thermal conductivities of the solid materials, on the PCT were predominantly ignored.

• 한국재난정보학회 논문집
• /
• 제11권2호
• /
• pp.203-209
• /
• 2015

열감지기는 화재시 발생되는 열을 감지하는 것으로 모든 소방대상물에 일반적으로 사용되는 자동화재탐지설비의 중요한 핵심 요소이다. 열감지기는 스포트(spot)형과 분포형으로 구분되며, 스포트형에는 차동식과 정온식이 있다. 이러한 열감지기는 실제 화재시 작동시간 및 작동온도 등 반응의 민감도에 따라 인명과 재산 손실에 큰 영향을 준다. 국내에서는 스프링클러 헤드제품에 응답시간지수를 도입하여 사용하고 있으나, 열감지기에 대해서는 현재 적용이 되어지지 않고 있으며, 반응의 민감도를 표시하는 응답시간지수의 도입이 필수적으로 본 연구에서는 국내 생산된 정온식 스포트형 열감지기와 다이아프램형 및 반도체 형식의 차동식 스포트형 열감지기에 대하여 풍동실험 및 화재실험을 통하여 응답시간지수, 작동시간, 작동온도 등에 대하여 연구하였다. 응답시간지수를 적용한 열감지기를 설치하여 신속한 경보로 인한 국민의 생명과 재산손실을 줄이는데 도움을 주고자 한다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1219-1224
• /
• 2004

The objective of this study is to propose an experimental calibration facility in which a heat flux sensor can be calibrated under conductive condition by using helium gas. The heat flux calibration facility was designed, simulated and manufactured for use in a high heat transfer condition. It delivers heat fluxes up to a maximum of 35 KW $m^{-2}$. A copper block heated electrically with 3.5 KW power is designed to produce uniform temperature up to 600 K across its face. High heat fluxes are provided between hot plate and cold plate by 1 mm height helium filled gap. A cold plate is maintained around 300 K through pool boiling using a refrigerant and water-cooled heat exchanger. A simulation was conducted to verify the design of the main test section. To verify the performance of calibration facility, a heat flux sensor was examined. The measured heat fluxes were compared to the calculated one.

• 한국환경보건학회지
• /
• 제39권6호
• /
• pp.492-504
• /
• 2013

Objectives: This analysis seeks to evaluate the impact of environmental health factors (EHF; e.g. hospital beds per capita, employees of medical institutions) on extreme-heat vulnerability assessment in Busan Metropolitan City during 2006-2010. Methods: According to the vulnerability concept suggested by the Intergovernmental Panel on Climate Change (IPCC), extreme-heat vulnerability is comprised of the categories of Exposure, Sensitivity, and Adaptive Capacity (including EHF). The indexes of the Exposure and Sensitivity categories indicate positive effects, while the Adaptive capacity index indicates a negative effect on extreme-heat vulnerability. Variables of each category were standardized by the re-scaling method, and then each regional relative vulnerability was computed with the vulnerability index calculation formula. Results: The extreme-heat vulnerability index (EVI) excepting EHF was much higher in urban areas than in suburban areas within the metropolitan area. When EHF was considered, the difference in the EVI between the two areas was reduced due to the increase of the Adaptive capacity index in urban areas. The low EVI in suburban areas was induced by a dominant effect of natural environmental factors (e.g. green area) within the Adaptive capacity category. Conclusions: To reduce the vulnerability to extreme heat in urban areas, which were more frequently exposed to extreme heat than others areas, public health and natural environments need to be improved in sensitive areas.

• 대한기계학회논문집
• /
• 제12권3호
• /
• pp.622-629
• /
• 1988

본 연구에서는 박판형 열유속 센서의 감도를 높임과 동시에 두께와 면적을 줄 이기 위한 방안으로서 시벡 계수(Seebeck doefficient)가 일반 열전대재료보다 월등히 큰 반도체 열전재료를 이용하여 박판형 센서를 제작하고 그 성능을 조사하였다. 센 서의 제작에 사용한 열전재료는 Melcor 사에서 열전 열펌프 생산에 사용하기 위하여 개발한 소자로서 통상 텔루루화 비스무스(bismuth telluride)라 불리우며 그 조성은 비스무스, 텔루륨, 셀레늄, 안티몬의 4가지 합금에 미량의 불순물(dopent)이 첨가된 것으로 불순물의 종류에 따라 전기적인 P형 또는 N형의 반도체가 되는 것으로 알려져 있으며 Table 1에 물성치가 나타나 있다.

• Journal of Acupuncture Research
• /
• 제31권4호
• /
• pp.133-141
• /
• 2014

Objectives : The purpose of this study is reporting to compare the preference of combustible moxibustion and electronic moxibustion. Methods : 31 patients were treated by combustible moxibustion in the morning and electronic moxibustion in the afternoon for 1 day. After they were treated by each moxibustions treatment, filled out questionnaire. We repeated the above process for 3 days. And we analyzed questionnaire statistically. Results : Heat sensitivity of electronic moxibustion has statistical significance. Sex and age have no statistical significances. Heat sensitivity and persistency of combustible moxibustion, heat persistency of electronic moxibustion also have no statistical significances. Satisfaction and smoke of moxibustion have correlation to moxibustion preference. Conclusions : Heat sensitivity of electronic moxibustion, satisfaction and smoke of moxibustion have correlation to moxibustion preference.

• 센서학회지
• /
• 제9권5호
• /
• pp.357-364
• /
• 2000

R.F. magnetron sputtering에 의해 $Al_2O_3$ 기판상에 $LaFeO_3$ 박막을 증착하고 막의 구조적, 전기적 및 가스감도 특성을 조사하였다. $600^{\circ}C$ 이상에서 열처리 된 박막에서 (121) 방향의 주결정상을 확인할 수 있었고 가스감지특성에서 박막은 p형 반도체의 특성을 보였다. 박막의 두께 및 열처리 온도의 변화에 대하여, 감도는 박막의 두께변화에는 둔감하였지만 열처리온도에는 큰 변화를 보였다. $800^{\circ}C$에서 열처리된 두께 400 nm의 박막에서 동작온도가 $300^{\circ}C$일때 5000 ppm의 CO 가스에 대해서는 약 400%, 350 ppm의 $NH_3$ 가스에서는 약 60%의 감도를 보였다.