• Title/Summary/Keyword: Heat Treatment T6

Search Result 291, Processing Time 0.033 seconds

Studies on the Hydrolysis of the Waste wood of Cortinellus edodes with Trichoderma viride Cellulase (표고재배폐재(栽培廢材)의 당화(糖化)에 관(關)한 연구(硏究))

  • Min, Du Sik
    • Journal of Korean Society of Forest Science
    • /
    • v.43 no.1
    • /
    • pp.31-34
    • /
    • 1979
  • In this study, enzymatic hydrolysis of the substrate of the waste wood of Cortinellus edodes was investigated using crude cellulase preparation of Trichoderma viride Pers. ex. Fr. SANK 16374. The crude cellulase was produced by the submerged culture process and produced in the culture fluid was salted out quantitatively by the use of ammonium sulfate. Reducing sugar was determined by the dinitrosalisylic acid (DNS) method. 1. The chemical composition of the waste wood was crude protein 2.26%, c. fat 2.57%, c. fibre 44.60%, c. ash 5.58% and lignin 13.62%. In amino acid composition, no cystine and methionine was showed, but trace amount of Vitamin A, $B_1$, and $B_2$, niacine and chloride were detected. (Table 1) 2. As heat treatment of the substrate was found to produce the highest reducing sugar yield being reacted for 48hr. with T.v cellulase, the substrate was heated to $190{\pm}5^{\circ}C$. for 45 min. either before or immediately after milling. 3. The substrate heated and ball milled at $190{\pm}5^{\circ}C$. for 45 min. the reducing sugar yield reached to 11.5%. 4. The substrate without any treatment was found to produce the highest reducing sugar yield being reacted 72hr. with T. v cellulase, the reducing sugar yield reached to 10.1%. 5. The rate of reducing sugar per each treated substrate was decreased by the order of the substrated, heated and then ball milled at $190{\pm}5^{\circ}C$. for 45 min. (11.5%)> without any treatment (10.1)> ball milled and heated at $190{\pm}5^{\circ}C$. for 45 min. (6.9%). 6. Saccharification of waste wood has been shown to be possible by heat treated and milling the substrate in contact with cellulase. And it is likely to be recommended that the waste wood may be valuable for raw materials of saccharification.

  • PDF

Clinical Study on 1 Case of patient with Urinary Retention (요폐환자(尿閉患者) 1례(例)에 대한 임상적(臨床的) 고찰(考察))

  • Kim, Jae-Hyeng;Cho, Chung-Sik;Kim, Chul-Jung
    • Journal of Haehwa Medicine
    • /
    • v.14 no.1
    • /
    • pp.43-49
    • /
    • 2005
  • One case of patient with urinary retention was reported in this clinical study. After the study, the results were as follows: 1. Anulesis belongs to l$\acute{o}$ng-bi(癃閉) in oriental medicine and the patient of this case belongs to chronic anulesis. 2. The patient of this case was thought as broke out anuresis by vesical nerve palsy of diabetic bladder pathy and sequela of stroke, and ischuria of long lie down 3. The patient of this case changeable process is supposed to urinary frequency, 'bi(閉)', 'l$\acute{o}$ong(癃)', urinary incontinence and urinary frequency. 4. First time of drug treatment is GAMIPHALJENG-SAN(ji$\bar{a}$-w$\grave{e}$i-b$\bar{a}$-h$\bar{e}$ng-s$\check{a}$n) by oral administration that action of alleviate a fever, water utilization and metaphase, convalescence time of drug treatment is PHALMIWANGAMI (b$\bar{a}$-w$\grave{e}$i-w$\acute{a}$n-ji$\bar{a}$-w$\grave{e}$i), YIKLUENG-TANG(yi-ling-t$\bar{a}$ng), CHUKYOO-TANG(s$\grave{u}$-ni$\grave{a}$o-t$\bar{a}$ng) that action of recreation. 5. Accupuncture treatment is s$\bar{a}$n-x$\bar{i}$ng-xuw$\acute{e}$, zw$\acute{u}$-s$\bar{a}$n-li, qi-h$\check{a}$i, gu$\bar{a}$n-yu$\acute{a}$n, zh$\bar{o}$ng-ji by mild supplementing and reducing manipulation of needle and heat accupuncture is qi-h$\check{a}$i, gu$\bar{a}$n-yu$\acute{a}$n, zh$\bar{o}$ng-ji-xu$\acute{e}$. 6. The other treatment is a sitz bath that prevent of urinary tract infection, and relieve of initial acute auresis by using of urethral catheterization.

  • PDF

Changes in Food Components of Dark, White-Fleshed Fishes by Retort Sterilization Processing -1. Changes in Nitrogenous Extractives and Textures- (레토르트 살균처리가 적색육 및 백색육 어류의 성분변화에 미치는 영향 -1. 함질소엑스분 및 텍스튜어의 변화-)

  • OH Kwang-Soo;SUNG Dae-Whan;CHOI Jong-Duck;LEE Eung-Ho
    • Korean Journal of Fisheries and Aquatic Sciences
    • /
    • v.24 no.2
    • /
    • pp.123-129
    • /
    • 1991
  • The skipjack and Alaska pollack meat were packed in square No. 3B can, and thermally processed at $121.1^{\cir}C$ so far as to reach Fo values of 5, 10 and 20, respectively. Also the another samples which were heated at $98^{\cir}C$ for 30 minutes were prepared. We have examined the changes of nitrogenous extractives and texture by thermal processing at high temperature in both fish meats. Moisture contents of both fish meats decreased slightly with the increasing of Fo values. When the samples were heated at $98^{\cir}C$ and $121.1^{\cir}C$, pH and VBN contents increased markedly in both fish meats; increasing ratio of pH and VBN contents in skipjack meat was larger than those of Alaska pollack meat. Histamine were detected in concentration of 6.1mg/100g, 0.1mg/100g in raw skipjack and Alaska pollack meat, 8.2mg/100g, 0.1mg/100g in Fo 20 samples of these fish meats, respectively. The contents of total free amino acids in skipjack and Alaska polack meat were 984.8mg/100g, 282.3mg/100g, and these total contents decreased slightly with increasing of Fo values. Little changes were observed in free amino acid composition, but only His, Tau, Ala in skipjack meat and Tau in Alaska pollack meat decreased significantly by heat treatment. Also the degredation of IMP were Proceeded during Preparation and heat treatment of samples, and TMAO changed into TMA almost equivalently. In changes of textures, as compared with heating of 98t for 30 minutes; Fo 5 heat treatment became more softened these fish meats.

  • PDF

고강도 및 파괴인성을 갖는 AI-Li-Cu 합금 개발

  • Kim, Song-Hui;Yun, Yeo-Beom;Hwang, Yeong-Hwa;Choe, Chang-U;Hong, Jun-Pyo;Lee, Eung-Jo
    • Korean Journal of Materials Research
    • /
    • v.3 no.3
    • /
    • pp.253-260
    • /
    • 1993
  • High strength and fracture toughness of Al-Li-Cu alloy(2090 Al alloy) have been achieved by the improvement of melting and casting, extrusion and heat treatment techniques. To establish the sucessful process for semi-industrial scale ingot(20Kg) the following areas have been investigated: (1) Improvement of melting and casting techniques for ingot by introducing atmospheric modifications, vacuum and rotary degassing, and deslagging. (2) The effect of heat treatment on mechanical properties (3) Mechanical characterization by tensile test, fracture toughness test and fatigue crack propagation test. High mechanical properties were found to be intimately related with ingot soundness. Tensile strength of final products varied from 534MPa to 566MPa in peak aged condition while elongation/ductility ranged from 9.0% to 11.9%. From the fracture toughness test with using compact tensile specimen, plane strain fracture toughness($K_{Ic}$) appeared to be 39MPa${\surd}$m in peak aged condition and 23MPa${\surd}$ m in underaged condition. When load ratios of 0.1, 0.3 and 0.5 were given ${\Delta}K_{th}$ was 6.0MPa${\surd}$ m, 5.3MPa${\surd}$ m and 4.3MPa${\surd}$ m respectively.

  • PDF

INVESTIGATIONS OF OXIDATIONS OF SnOx AND ITS CHANGES OF THE PROPERTIES PREPARED BDEPOSITIONY REACTIVE ION-ASSISTED

  • Cho, J.S.;Choi, W.K.;Kim, Y.T.;Jung, H.J.;Koh, S.K.
    • Journal of the Korean institute of surface engineering
    • /
    • v.29 no.6
    • /
    • pp.766-772
    • /
    • 1996
  • Undoped $SnO_x$ thin films were deposited on Si(100) substrate by using reactive ioassisted deposition technique (R-IAD). In order to investigate the effect of initial oxygen content and heat treatment on the oxidation state and crystalline structure of tin oxide films, $SnO_x$ thin films were post-annealed at 400~$600^{\circ}C$ for 1 hr. in a vacuum ~$5 \times 10^{-3}$ -3/ Torr or were directly deposited on the substrate of $400^{\circ}C$ and the relative arrival ration ($Gamma$) of oxygen ion to Sn metal varied from 0.025 to 0.1, i.e., average impinging energy ($E_a$) form 25 to 100 eV/atom. As $E_a$ increased, the composition ratio of $N_ON{sn}$ changed from 1.25 to 1.93 in post-annealing, treatment and 1.21 to 1.87 in in-situ substrate heating. In case of post-annealing, the oxidation from SnO to $SnO_2$ was closely related to initial oxygen contents and post-annealing temperature, and the perfect oxidation of $SnO_2$ in the film was obtained at higher than $E_a$=75 eV/atom and $600^{\circ}C$. The temperature for perfect oxidation of $SnO_2$ was reduced as low as $400^{\circ}C$ through in-situ substrate heating. The variation of the chemical state of $SnO_x$ thin films with changing $E_a$'s and heating method were also observed by Auger electron spectroscopy.

  • PDF

Purification of Antioxidant substance from the stem bark of Rhus verniciflua

  • Kim, Jung-Bae
    • Proceedings of the Korean Journal of Food and Nutrition Conference
    • /
    • 2001.12a
    • /
    • pp.126-126
    • /
    • 2001
  • The Rhus verniciflua contains alkly(en)-catechol type allergens with a saiurated or unsaturated alkly chain of 15 or 17 carbon atoms. It has been recognized as an extremely active allergen causing skin reactions similar In poison ivy. The allergic contact dermatitis induced by the urushiol is known to be mediated be T lymphocytes whicht specifically recognize the hepten urushiol. Therefore. direct use of this plant as a medicinal purpose might imply a considerable hazard in Korea. In this study, using the established method for the detoxification from the stem bark of Rhus verniciflua, an strong antioxidant substance was isolated and characterized DPPH (diphenypricryl hydrazyl) assay measures hydrogen atom-donating activity and hence provides a measure of free radical scavenging antioxidant activity. DPPH, a purple-colored stable free radical, is reduced to yellow-colored diphenylpicryl hydrazine by antioxidants to deducing agents. Antioxidative effects of the water extract from RV were measured by DPPH assay. Twenty microliters of the extract was added to 1ml of 100mM DPPH solution in ethanol The mixture was shaken and left to stand for 10min at room temperature. The crude water extracts was purified by using HPLC method with a DEAE (anionic type), CN, ODS column. The purified compound remained stable at pH 3.0-6,0, but unstable above pH 6.5. It was stable heat at 10$0^{\circ}C$ for 4 hours, but still had about 80% of residual activity after treatment at 10$0^{\circ}C$ for 5 hours. The elemental composition of the HR-EI mass spectrum at m/z 170.02 was estimated the empirical formula as $C_{7}$ $H_{6}$ $O_{5}$. $C_{10}$ $H_4$ $O_2$N$_1$, $C_{5}$ $H_4$ $O_4$N$_3$, $C_{8}$$H_2O$$_1$N$_4$. In antimicrobial test, no inhibition was observed against Gram-positive and negative bacteria. This compound was stronger than that of commercial antioxidant by DPPH test, such as BHT, BHC at the same concentration (20$\mu$g/ml).ml).

  • PDF

Cloning and Expression of a Chitinase Gene from Thermoactinomyces vulgaris KFB-C100

  • Yooh, Ho-Geun;Kim, Hee-Yun;Lim, Young-Hee;Cho, Hong-Yon
    • Journal of Microbiology and Biotechnology
    • /
    • v.8 no.6
    • /
    • pp.560-567
    • /
    • 1998
  • We have found that Thermoactinomyces vulgaris KFB-Cl00 produces a chitinase. The optimum temperature and pH of the enzyme activity were $55^{\circ}C$ and 6.5. The enzyme was stable after heat treatment at $80^{\circ}C$ for 30 min and stable in acidic and basic conditions (PH 6.0~11.0). The thermostable endo-chitinase from Thermoactinomyces vulgaris KFB-C100 was cloned into the plasmid pBR322 by using E. coli DH5$\alpha$ as a host strain. The positive clone carrying a recombinant plasmid (PKCHI23) with a 4.1-kb fragment containing the chitinase gene was found. The recombinant plasmid was analyzed to determine the essential region for chitinase activity and obtained a 2.3-kb fragment, which was sub cloned into pTrc99A using the PstI and SalI sites to construct pTrc99A/pKCHI23-3. The resulting plasmid exerted high chitinase activity upon transformation of E. coli XL1-Blue cells. Chitinase was overproduced 14 times more in the clone cells than in the wild-type cells and the enzyme was purified to homogeneity. The purified enzyme showed the similar properties as the native chitinase from T. vulgaris in terms of molecular weight and substrate specificity. The catalytic action of the cloned enzyme was an endo type, producing chitobiose as a major reaction product.

  • PDF

Investigation on the Sintering Behavior and Mechanical Properties of Al-Zn-Mg Alloy Powders Mixed with Al-Si-SiC Composite Powders (Al-Si-SiC 복합분말과 Al-Zn-Mg계 합금분말이 혼합된 분말의 소결 거동 및 기계적 특성연구)

  • Jang, Gwang-Joo;Kim, Kyung Tae;Yang, Sangsun;Kim, Yong-Jin;Park, Yong-Ho
    • Journal of Powder Materials
    • /
    • v.21 no.6
    • /
    • pp.460-466
    • /
    • 2014
  • Al-Si-SiC composite powders with intra-granular SiC particles were prepared by a gas atomization process. The composite powders were mixed with Al-Zn-Mg alloy powders as a function of weight percent. Those mixture powders were compacted with the pressure of 700 MPa and then sintered at the temperature of $565-585^{\circ}C$. T6 heat treatment was conducted to increase their mechanical properties by solid-solution precipitates. Each relative density according to the optimized sintering temperature of those powders were determined as 96% at $580^{\circ}C$ for Al-Zn-Mg powders (composition A), 97.9% at $575^{\circ}C$ for Al-Zn-Mg powders with 5 wt.% of Al-Si-SiC powders (composition B), and 98.2% at $570^{\circ}C$ for Al-Zn-Mg powders with 10 wt.% of Al-Si-SiC powders (composition C), respectively. Each hardness, tensile strength, and wear resistance test of those sintered samples was conducted. As the content of Al-Si-SiC powders increased, both hardness and tensile strength were decreased. However, wear resistance was increased by the increase of Al-Si-SiC powders. From these results, it was confirmed that Al-Si-SiC/Al-Zn-Mg composite could be highly densified by the sintering process, and thus the composite could have high wear resistance and tensile strength when the content of Al-Si-SiC composite powders were optimized.

Korean Red Ginseng improves atopic dermatitis-like skin lesions by suppressing expression of proinflammatory cytokines and chemokines in vivo and in vitro

  • Kee, Ji-Ye;Jeon, Yong-Deok;Kim, Dae-Seung;Han, Yo-Han;Park, Jinbong;Youn, Dong-Hyun;Kim, Su-Jin;Ahn, Kwang Seok;Um, Jae-Young;Hong, Seung-Heon
    • Journal of Ginseng Research
    • /
    • v.41 no.2
    • /
    • pp.134-143
    • /
    • 2017
  • Background: The prevalence of allergic inflammatory diseases such as atopic dermatitis (AD), asthma, and allergic rhinitis worldwide has increased and complete recovery is difficult. Korean Red Ginseng, which is the heat-processed root of Panax ginseng Meyer, is widely and frequently used as a traditional medicine in East Asia. In this study, we investigated whether Korean Red Ginseng water extract (RGE) regulates the expression of proinflammatory cytokines and chemokines via the mitogen-activated protein kinases (MAPKs)/nuclear factor kappa B ($NF-{\kappa}B$) pathway in allergic inflammation. Methods: Compound 48/80-induced anaphylactic shock and 1-fluoro-2,4-dinitrobenzene (DNFB)-induced AD-like skin lesion mice models were used to investigate the antiallergic effects of RGE. Human keratinocytes (HaCaT cells) and human mast cells (HMC-1) were also used to clarify the effects of RGE on the expression of proinflammatory cytokines and chemokines. Results: Anaphylactic shock and DNFB-induced AD-like skin lesions were attenuated by RGE administration through reduction of serum immunoglobulin E (IgE) and interleukin (IL)-6 levels in mouse models. RGE also reduced the production of proinflammatory cytokines including $IL-1{\beta}$, IL-6, and IL-8, and expression of chemokines such as IL-8, thymus and activation-regulated chemokine (TARC), and macrophage-derived chemokine (MDC) in HaCaT cells. Additionally, RGE decreased the release of tumor necrosis $factor-{\alpha}$ ($TNF-{\alpha}$), $IL-1{\beta}$, IL-6, and IL-8 as well as expressions of chemokines including macro-phage inflammatory protein $(MIP)-1{\alpha}$, $MIP-1{\beta}$, regulated on activation, normal T cell expressed and secreted (RANTES), monocyte chemoattractant protein (MCP)-1, and IL-8 in HMC-1 cells. Furthermore, our data demonstrated that these inhibitory effects occurred through blockage of the MAPK and $NF-{\kappa}B$ pathway. Conclusion: RGE may be a useful therapeutic agent for the treatment of allergic inflammatory diseases such as AD-like dermatitis.

Effect of titanium powder on the bond strength of metal heat treatment (티타늄 파우더가 금속의 열처리 시 결합강도에 미치는 영향)

  • Kim, Sa-Hak;Kim, Wook-Tae
    • Journal of Dental Rehabilitation and Applied Science
    • /
    • v.33 no.2
    • /
    • pp.71-79
    • /
    • 2017
  • Purpose: Ni-Cr alloy does not contain Beryllium, causing the metal compound to form oxides in the furnace but by using Titanium as a chemical catalyst the forming of the oxides can be controlled, and by controlling the impurities formed on the metal surface, the possibility of the Ni-Cr alloy bond strength being increased can be analysed. Materials and Methods: Titanium was used as a chemical catalyst in the porcelain for the oxidation of beryllium-free metal (Ni-Cr) alloy. The T1 group, which does not use Titanium power as a chemical catalyst is a reference model for comparison. The T2 group and T3 group used 10 g and 20 g of Titanium power, respectively. They are fabricated to observe the shear bond strength and surface properties. There was no significance when One-way ANOVA analysis/Tukey Honestly Significant Difference Test was conducted for statistical analysis among groups (P > 0.05). Results: Results of measuring the three-point flexural bond strength of the Ni-Cr alloy and thickness of the oxide film. Experiment T3 using 20 g Titanium chemical catalyst: $39.22{\pm}3.41MPa$ and $6.66{\mu}m$, having the highest bond strength and thinness of oxide film. Experiment T2 using 10 g Titanium chemical catalyst: $34.65{\pm}1.39MPa$ and $13.22{\mu}m$. Experiment T1 using no Titanium chemical catalyst: $32.37{\pm}1.91MPa$ and $22.22{\mu}m$. Conclusion: The T2 and T3 experiments using Titanium chemical catalyst showed higher bond strength for the Ni-Cr alloy and lower thickness of oxide film than experiment T1, and the titanium catalyst being able to increase bond strength was observed.