• Journal of the Korean institute of surface engineering
• /
• v.40 no.4
• /
• pp.170-174
• /
• 2007

High Velocity Oxygen Fuel (HVOF) thermal spray coating of nano size WC-Co powder (nWC-Co) has been studied as one of the most promising candidate for the possible replacement of the traditional hard plating in some area which causes environmental and health problems. nWC-Co powder was coated on Inconel 718 substrates by HVOF technique. The optimal coating process obtained from the best surface properties such as hardness and porosity is the process of oxygen flow rate (FR) 38 FMR, hydrogen FR 57 FMR and feed rate 35 g/min at spray distance 6 inch for both surface temperature $25^{\circ}C\;and\;500^{\circ}C$. In coating process a small portion of hard WC decomposes to less hard $W_2C$, W and C at the temperature higher than its decomposition temperature $1,250^{\circ}C$ resulting in hardness decrease and porosity increase. Friction coefficient increases with increasing coating surface temperature from 0.55-0.64 at $25^{\circ}C$ to 0.65-0.76 at $500^{\circ}C$ due to the increase of adhesion between coating and counter sliding surface. Hardness of nWC-Co is higher or comparable to those of other hard coatings, such as $Al_2O_3,\;Cr,\;Cr_2O_3$ and HVOF Tribaloy 400 (T400). This shows that nWC-Co is recommendable for durability improvement coating on machine components such as high speed spindle.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.4.1-4.1
• /
• 2010

In the first part, after discussing works on nacre, a soft-hard composite found in nature, including a simulation on network mimicking nacre [1-4], we talk on a simple model of spider webs, another example of natural soft-hard structure [5]. We demonstrate that the web network is free of stress concentrations because the radial threads are stronger than the spiral threads. In the second part, after reviewing our works on wetting on textured surfaces [6-8], we discuss penetration into textured surface and instability of a liquid film on textured substrates during spin coating [9,10].

• Tribology and Lubricants
• /
• v.16 no.6
• /
• pp.415-424
• /
• 2000

The use of magnetoresistive (MR) head requires much tighter control of particle contamination in a drive since loose particles on the disk surface will generate thermal asperities (TA). In this study, a spinoff test was performed to investigate the adhesion and removal capability of a particle to disk surface. Numerical simulation was also performed to investigate dominant factor of particle detachment and to support experimental results. It was shown that particles are detached from the disk surface by the moment derived from the centrifugal force and the drag force and that the centrifugal force and capillary force are the dominant force, which determines spin-off of a particle on the disk surface. Removal of particles smaller than several micrometers, which are the main source of TA generation, is extremely difficult since the adhesion forces exceed the centrifugal force. Lubricant types and manufacturing process also influence the particle removal. Lower bonding ratio and lower viscosity of the lubricant will help to increase the removal rate of the particles from the disk surface.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.11a
• /
• pp.63-63
• /
• 2001

As a new approach to substitute for a hard alloy of stellite 6B containing Co which is radioactive in nuclear system, a hard-phase coating of CrN will be applicable to protect 12Cr steel from erosion at leading edge on steam turbine blade. The CrN coating was prepared by arc ion plating on 12 Cr steel and was undertaken in liquid impact test at the velocity of 35Om/sec, which simulate the environment in the last stage of blade. The erosion resistance of coating was evaluated by optical observation on damaged surface. The threshold number of impact was closely related with surface hardness. And thus, it was confirmed that surface hardening improves the life time of steam turbine blade.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.10
• /
• pp.869-875
• /
• 2015

In this paper, the surface wave that caused the isolation problem when the design of the array antenna is studied. The grounded dielectric slab model is used in order to simulate in the similar environment with the surface wave of the microstrip patch antenna. The propagation of the surface wave on the various types of grounds which are defected ground structure(DGS), perfect magnetic conductor(PMC), Soft-surface, and Hard-surface is simulated. As a result, 25 % power is blocked by the DGS when the TM-wave incident. Also, 95 % power is blocked by the PMC and Soft-surface. This study will be very useful to increase the gain of an array antenna by improving the isolation between the antenna elements.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.53-60
• /
• 1999

As the flying height decreased, it is essential that hard disk drives perform reliable under various environmental conditions. In this paper the tribological characteristics of a head/disk interface are investigated under various temperature, relative humidity, altitude and outgas conditions. Specially, Contact-Start-Stop(CSS) tests were performed to assess the stiction, acoustic emission, slider take-off behavior, and track average amplitude(TAA). It is shown that the surface damage and head failure are accelerated by high temperature and humidity as well as low ambient pressure.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.131-138
• /
• 1998

It is essential that hard disk drives perform reliable under various temperature, humidity, and ambient pressure conditions. In this paper the tribological characteristics of a head/disk interface are investigated under various environmental conditions. Specially, Contact-Start-Stop(CSS) tests were performed to assess the stiction and slider take-off behavior. It is shown that the surface damage is accelerated by high temperature and humidity as well as low ambient pressure.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.4
• /
• pp.291-295
• /
• 2003

Many steam turbine components encounter solid particle erosion damage. It has been reported that particle erosion damage is caused by oxide scale exfoliation from boiler tubes. One of the most effective solutions to combat the erosion damage is the application of erosion resistant coatings on the turbine components. In this study, particle erosion resistance for various hard coatings such as nitride, Cr carbide and boride coatings was evaluated under the simulated erosion conditions of steam turbines. Based on the particle erosion tests, the boride coating was found to be more superior to others.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.11
• /
• pp.55-63
• /
• 2003

In this study, an experimental research of grinding characteristics using super-abrasives for surface carburized and heat treated SCM415 materials, which were usually used to make a linear motion guide block and were comparatively hard-to-machine materials, was carried out. In order to conduct a high efficiency and a accuracy grinding of such materials, grinding processes using CBN (Cubic boron nitride) and 38P grinding wheels have been attempted on a surface grinding machine. The grindability according to each grinding conditions was evaluated by means of a grinding force, a surface roughness and a residual stress. The experimental methods and results were presented in this paper. And also, from a proposed truing method the CBN wheels that combined a copper and a break truer gave a full scope to the wheel's performance.

• Journal of the Korean Ceramic Society
• /
• v.42 no.10 s.281
• /
• pp.645-648
• /
• 2005

To fabricate a (100) silicon hard master, we used anisotropic wet etching for the embossing. The etching chemical for the sili­con wafer was a TMAH 25$\%$ solution. The anisotropic wet etching produces a smooth sidewall surface inclined at 54.7°, and the surface roughness of the fabricated master is about 1 nm. After spin coating an organic-inorganic sol-gel hybrid resin on a silicon substrate, we used the fabricated master to form patterns on the silicon substrate. Thus, we successfully obtained patterns via the hot embossing technique with the (100) silicon hard master. Moreover, by using a single hydrophobic surface treatment of the master, we succeeded in achieving uniform surface roughness of the embossed patterns for more than ten embossments.